Red Dragon patio light User manual

Flame Engineering Inc. • PO Box 577 • LaCrosse KS 67548 • 800-255-2469 • 785-222-2873 • 785-222-3619 Fax • www.FlameEngineering.com
Owner Manual/Assembly Instructions
Red Dragon Patio Lights
NOTE: Unpack and inspect for damage. Retain this information sheet for future reference.
FOR YOUR SAFETY...
DO NOT use this Patio Light in areas where gasoline
or other flammable liquids are stored or used.
Intended for outdoor use only.
Check with local
natural gas or propane
supplier for ordinances,
requirements, etc. prior
to installation of your
new Patio Light. Check
all gas connections
prior to lightup,
ensuring a safe and
operative unit.
• Visually inspect Patio Light prior to each use. Ask a qualified service person to
inspect hose assembly annually for evidence of abrasion, wear or cuts. Replace hose
assembly if any of these conditions are present.
• Read all instructions and warnings contained in this manual.
• Follow procedures step by step.
ALWAYS
Cylinder not included!
Temperatures near Patio Light Head will ignite
combustible materials. Use only on level and
stable surfaces. Keep Patio Lite Head at least 6’
away from any combustible materials.
WARNING

ASSEMBLY INSTRUCTIONS FOR PORTABLE PATIO LIGHTS
1. Remove parts from carton and check against parts list. If all
parts are not located please call our toll free number -
1-800-255-2469.
2. Assemble axle (E) and both wheels (D) on cart frame (C).
Be sure extended side or hub of wheel (D) is toward cart
frame (C). Place axle caps on outside of wheels. Firmly tap
axle caps with hammer.
3. Feed the 3/8 inch female flare fitting of hose through the
hole in the side of the lower post section (B2) and on
through the upper post section (B1). Connect 3/8 inch
female flare fitting to the 3/8 inch male flare fitting located
on the Patio Light head (A). Tighten the connection with a
wrench (no need for tape or pipe compound).
4. Insert upper post section (B1) into Patio Light head collar.
Insert 3/8 inch x 1/4 inch set screws (2) tighten securely
with allen wrench. Insert lower post section (B2) into upper
post section (B1) making sure to align set screw hole.
Insert 5/16 inch button head cap screw and tighten with
Part Numbers
PT 300-6 C
PT 301-6 C
PT 302-6 C
PT 311-6 C
PT 411-6 C
Package Includes: Owner Manual/Assembly Instructions, Cylinder
Strap, Axle Caps (2), 3/8 inch x 1/4 inch long set screws (2), 5/16
inch button head cap screws (2) and allen wrench.
You will need: Hammer & an adjustable end wrench.
C
Cart Rear View
DD
E
Axle Caps
3/8" x 1/4"
Set Screws
Valve
F
A
B1
B2
CD
5/16" Button Head
Cap Screw
5/16" Button Head
Cap Screw
Flame Engineering Inc. • PO Box 577 • LaCrosse KS 67548 • 800-255-2469 • 785-222-2873 • 785-222-3619 Fax • www.FlameEngineering.com
Turn all valves to an off position. Head valve must be turned
clockwise to be in an off position. Open source/cylinder valve
slowly, open head valve slightly and light with a long grill or
fireplace lighter. Adjust to desired flame using head valve. DO
NOT LEAVE UNATTENDED. When Patio Light is not in use,
be sure source/cylinder valve is closed.
LIGHTING INSTRUCTIONS
allen wrench. Place assembled post and head into post
cuff of cart frame (C). Be sure to align the set screw hole.
Gently pull hose through exit hole to prevent kinking. Insert
button head cap screw and tighten with allen wrench.
5. Position cylinder on cart frame (C) and secure with
enclosed strap. Attach inlet fitting (P.O.L.) to cylinder. This
is a left handed fitting and requires no pipe compound.
CLOSE HEAD VALVE. Head valve must be turned
clock-wise to be in an off position. Using soapy water,
open cylinder valve slowly and check all connections for
gas leaks. Correct any leaks before using. This testing
procedure should be done once a month.
Parts List
A. Patio Light Head w/ valve
B1. Upper Post Section
B2. Lower Post Section w/ Cuff
C. Cart Frame
D. Cart Wheels (2)
E. Axle
F. Hose, Regulator and POL

ASSEMBLY INSTRUCTIONS FOR PERMANENT PATIO LIGHTS
Part Numbers
PT 300-6 PM
PT 301-6 PM
PT 302-6 PM
PT 311-6 PM
PT 411-6 PM
Package Includes: Owner Manual/Assembly Instructions, 3/8 inch x
1/4 inch long set screws (2), 5/16 inch button head cap screws (2)
and allen wrench.
A 3/16 inch allen wrench is provided. You will need an adjustable-end wrench.
1. Remove all parts from carton and check against parts list. If
all parts are not located please call our toll free number -
1-800-255-2469.
2. The Patio Light base (A) is manufactured with two supply
line inlets. Please choose either the side or bottom supply
line as your fuel i nlet and remove the plug accordingly in
order to connect to gas supply. The rubber grommet (H)
provided, will protect the fuel line should you decide to use
the side supply inlet. Be certain to use thread compound
provided on gas supply connection. Section (A) should be
set in concrete a minimum of 12 inches for maximum
stability. Please allow sufficient time for concrete to set
and cure.
3. When concrete is dry and the base section (A) is secure,
proceed with Patio Lite assembly. Feed fuel supply hose
(D) through lower post section (B). Connect lower post
section (B) to base section (A) and tighten with 5/16inch
button head cap screw (G) provided.
4. Feed fuel supply hose (D) through upper post section (C).
Insert lower post section (B) into upper post section (C)
making sure to align the set screw hole. Insert 5/16 inch
button head cap screw (G) and tighten with allen wrench
provided.
5. Connect fuel supply hose (D) to Patio Light head (E). No
pipe compound is necessary on this connection as this is a
flare fitting. Tighten with wrench.
6. Insert upper post section (C) into Patio Light head collar (E).
Insert the 3/8 inch x 1/4 inch set screws (F) and tighten
with allen wrench provided.
7. When installation is complete, open gas supply valve and
test all gas connections with soapy water before lighting.
Do not use a match or open flame to check for leaks.
Correct all leaks and test with soapy water before lighting.
SEE THE BACK PAGE FOR INSTALLATION PLUMBING EXAMPLES.
A
B
C
D
F F
E
G
G
H
Remove Plug
If Fuel Source
Will Connect Here
Remove Plug If Fuel
Source Will Connect Here
Bury Below Ground
Level 12" Minimum
Valve
Flame Engineering Inc. • PO Box 577 • LaCrosse KS 67548 • 800-255-2469 • 785-222-2873 • 785-222-3619 Fax • www.FlameEngineering.com
Turn all valves to an off position. Head valve must be turned
clockwise to be in an off position. Open source/cylinder valve
slowly, open head valve slightly and light with a long grill or
fireplace lighter. Adjust to desired flame using head valve. DO
NOT LEAVE UNATTENDED. When Patio Light is not in use,
be sure source/cylinder valve is closed.
LIGHTING INSTRUCTIONS
Parts List
A. Patio Light Base w/ Pipe Insert
B. Lower Post Section w/ Cuff
C. Upper Post Section
D. Fuel Supply Hose - connected to A
E. Patio Light Head w/valve
F. (2) 3/8 inch x 1/4 inch Set Screws
G. (2) 5/16 inch Button Head Cap Screws
H. Rubber Grommet
I. (2) Pipe Compound Capsule

PERMANENT PATIO LIGHTS INSTALLATION SUGGESTIONS:
Flame Engineering Inc. • PO Box 577 • LaCrosse KS 67548 • 800-255-2469 • 785-222-2873 • 785-222-3619 Fax • www.FlameEngineering.com
ALWAYS
• This Patio Light is designed and intended for outdoor use only.
•DO NOT place under a covered or enclosed patio or the eaves of your home.
•DO NOT place under low hanging trees or close to evergreens or shrubs.
•DO NOT move, handle or service Patio Light while it is in operation or hot.
•DO NOT allow children to play on or around the Patio Light. It could cause a fire or
bodily burns. Place in a low traffic area.
•DO NOT leave unattended. Close gas valves when unattended or not in use.
• Installation must comply with all applicable codes.
• Patio Light must be set level and comply with minimum clearance of 6' from all sides.
• Using soapy water, check all gas connections for leaks and test function of all moving
parts. Perform these checks and tests prior to initial use and after periodic use.
• Follow safety, maintenance and operating instructions contained in this owner manual.
8-2010
®
Example 2
Example 1
Example 3
Example 4