red roo DHS9-5 User manual

SAFETYPRECAUTIONS
AND OPERATING
INSTRUCTIONS
™
DHS
HYDRAULIC POST
HOLE DIGGER
6. GETTING STARTED: Push machine tothe
location of the first hole. Start engine and allow to
reach operating temperature. Standing at the rear
of the machine at the control handle. To begin
digging a hole, pull the right hand side of the
control lever. This will cause the auger to turn in a
clockwise direction. Apply downward pressure to
begin digging the hole. If dirt remains in the hole
use an up and down motion toclear excess dirt.
Release the control lever tostop auger. To
reverse the auger rotation (counter-clockwise),
pull the left hand side of the control lever.
7. The amount of force exerted will depend on
the hardness and type of ground conditions.
8. Remember, the DHS is a single person operation,
designed for earth drilling. There may be holes that
will be extremely difficult,if not impossible, to drill.
9. If ground is too hard to drill or the auger is jamming
on ground conditions or foreign objects (eg. wire,
tree roots, etc.), the pressure relief will function,
stalling the auger rotation. Clear auger and start
again. The operator presence control will ensure
quick stop if hand is removed from control lever.
NEVER TIE OR JAM LEVER INTO THE ON
POSITION (FORWARD OR REVERSE).
REVERSE (COUNTER CLOCKWISE) MAY
BE REQUIRED TO UNSCREW JAMMED AUGERS.
10. Do not attempt to drill auger to full depth in one
operation. Continually clearing the hole in an up
and down motion will facilitate a much easier
drilling operation. It may be necessary to clear
cutters and auger flighting from time to time to
ensure quicker and easier cutting.
11. Remember, as in drilling a hole in steel, one needs a
sharp drill. Auger, teeth and pilot MUST be in good
condition if the auger is to work correctly. See wear
parts section for more information.
12. Auger motor head assembly may be
tilted as per incline when drilling on
slopes. DO NOT change the digger
position during drilling. DO NOT operate on a
slope that exceeds 15˚
13. DO NOT over reach. Ensure proper footing and
balance when working with this machine.
WARNING! –Keep hands and feet
clearof all moving parts at all times!
WARNING! –Keep hands and
feet clear of exhaust muffler during
or soon after operation.
14. WARNING! –in case of difficulty,
release the control lever to stop
the auger. All digging action stops.
Press the engine "STOP" button located on
the engine. (See illustration)
15. DO NOT OPERATE
CLOSE TO EDGES
OR EXCAVATIONS ETC.
CHECK FOR ELECTRICAL AND GAS LINES
BEFORE DIGGING
AFTER USE
1) Turn fuel tap to "OFF" position.
2) Allow machine to cool down. Wash mud
and dirt off of the hydraulic post hole digger.
Ensure no water enters the carburettor.
3) Remove any objects that may have wrapped
around the auger.
© Copyright 2012, Red Roo Sales & Service Company Pty. Ltd. 1301-0025-A
Commercial Outdoor Power Equipment
5.
a.
b.
STARTING THE ENGINE:
c.
d. Turning the engine switch
to the ON position.
To start a cold engine, move the choke
lever or choke rod (applicable types) to
the CLOSED position. To restart a warm
engine,leave the choke lever or choke
rod in the OPEN position.
Move the fuel valve lever to ON position.
Move the throttle lever away from
the MIN position,about 1/3 of the
way toward the MAX position.
RECOIL STARTER
Pull the starter grip lightly until you
feel resistance, then pull briskly.
Return the starter grip gently.
a.
Shut off switch on
console should be
used, not shut off
switch on engine.
b. Turn the engine switch
to the OFF position.
c. Turn the fuel
valve lever to the
OFF position.
16. STOPPING THE ENGINE:
Move the throttle lever
to the MIN position.
Some engine applications use a
remote-mounted throttle control
rather than the engine-
mounted lever shown here
SAFETYPRECAUTIONS
AND OPERATING
INSTRUCTIONS
™
DHS9-5
HYDRAULIC POST
HOLE DIGGER
OPERATION
1) Remove the garden tiller
from its trailer/carrier. Use caution.
2) Familiarize yourself with the machine and its
controls.
3) Ensure the safety clutch control lever is in the
disengagedposition. The safety clutch
control lever is located on the left handle bar.
The disengaged position of the lever is down.
4) Remove the shaft locking pin located behind
the wheel axle. Store pin in hole provided on
left hand side of handle bar.
5) The wheel axle will now pivot. Lift up on the
handle to allowwheelaxle to pivot. For
transport, keep the wheel axle forward. When
cultivating, keep the wheel axle rearward for
added stability and control.
DO NOT transport the tillerwith the wheel
axle in the rear position.
6) Adjust depth shoe(ifequipped) by removing
shaft locking collarand slidingdepth shoe to
desired position. Replace shaft locking collar.
7) Open fuel shut-off valve. Set choke
control to Choke or Start position.
Set throttle control to Run or Fast
position. Set engine
stop switch to On or
Run position. Pull
starter cord rapidly.
Repeat (if necessary)
with choke off.
8) When in position to begingarden tilling,
engage the safety clutch controllever. The
tyneswillbeginrotating. Wheel axle must be in
the rearpositionwhile tilling.Release the
safety clutch controllever to stop the tynes
rotating. Tynespeed is governed by engine
throttle setting.
WARNING! –KEEPHANDSAND
FEET CLEAR OF TYNES AT ALL
TIMES!
9) Do not hurry the job. Proceed slowly and allow
the machine time to do the job. When ground
is extremely hard, reduce engine speed.
WARNING! –IN CASE OF DIFFICULTY,
DISENGAGE THE SAFETY CLUTCH
CONTROL LEVER. ALL TILLING ACTION
STOPS.Press the engine"STOP"button
located on the engine.
10) Stop Engine: Release the safety clutch control
lever.Move throttle to Slowposition. Set engine
stop switch to Stop or Offposition.DO NOT move
choke control to Choke
or Start position to stop
engine.Backfire or
enginedamagemay
occur.
AFTER USE
1) Turn fuelshut off valve to the "OFF"
position.
2) Allow machine to cool down.
3) Wash mud and dirt off of the garden tiller.
Ensure no water enters the carburettor.
4) Removeanyweeds,wire,rope or other
material thatmayhavewrappedaround the
tynes and rotor assembly.
5) Returnwheelaxle to forwardposition for
transport. Replace shaft locking collar.
6) Returndepth shoe(ifequipped) to full Up
position.
© Copyright 2001, Red Roo Sales & Service Company Pty. Ltd. 1301-0018
Commercial Environmental Equipment
Online Demonstration Available at:
www.redroo.com/products/postholediggers
SAFETYPRECAUTIONS
AND OPERATING
INSTRUCTIONS
™
GT622
GARDEN
TILLER
OPERATION
1) Remove the garden tiller
from its trailer/carrier. Use caution.
2) Familiarize yourself with the machine and its
controls.
3) Ensure the safety clutch control lever is in the
disengagedposition. The safety clutch
control lever is located on the left handle bar.
The disengaged position of the lever is down.
4) Remove the shaft locking pin located behind
the wheel axle. Store pin in hole provided on
left hand side of handle bar.
5) The wheel axle will now pivot. Lift up on the
handle to allowwheelaxle to pivot. For
transport, keep the wheel axle forward. When
cultivating, keep the wheel axle rearward for
added stability and control.
DO NOT transport the tillerwith the wheel
axle in the rear position.
6) Adjust depth shoe(ifequipped) by removing
shaft locking collarand slidingdepth shoe to
desired position. Replace shaft locking collar.
7) Open fuel shut-off valve. Set choke
control to Choke or Start position.
Set throttle control to Run or Fast
position. Set engine
stop switch to On or
Run position. Pull
starter cord rapidly.
Repeat (if necessary)
with choke off.
8) When in position to begingarden tilling,
engage the safety clutch controllever. The
tyneswillbeginrotating. Wheel axle must be in
the rearpositionwhile tilling.Release the
safety clutch controllever to stop the tynes
rotating. Tynespeed is governed by engine
throttle setting.
WARNING! –KEEPHANDSAND
FEET CLEAR OF TYNES AT ALL
TIMES!
9) Do not hurry the job. Proceed slowly and allow
the machine time to do the job. When ground
is extremely hard, reduce engine speed.
WARNING! –IN CASE OF DIFFICULTY,
DISENGAGE THE SAFETY CLUTCH
CONTROL LEVER. ALL TILLING ACTION
STOPS.Press the engine"STOP"button
located on the engine.
10) Stop Engine: Release the safety clutch control
lever.Move throttle to Slowposition. Set engine
stop switch to Stop or Offposition.DO NOT move
choke control to Choke
or Start position to stop
engine.Backfire or
enginedamagemay
occur.
AFTER USE
1) Turn fuelshut off valve to the "OFF"
position.
2) Allow machine to cool down.
3) Wash mud and dirt off of the garden tiller.
Ensure no water enters the carburettor.
4) Removeanyweeds,wire,rope or other
material thatmayhavewrappedaround the
tynes and rotor assembly.
5) Returnwheelaxle to forwardposition for
transport. Replace shaft locking collar.
6) Returndepth shoe(ifequipped) to full Up
position.
© Copyright 2001, Red Roo Sales & Service Company Pty. Ltd. 1301-0018
Commercial Environmental Equipment
SAFETYPRECAUTIONS
AND OPERATING
INSTRUCTIONS
™
GT622
GARDEN
TILLER
OPERATION
1) Remove the garden tiller
from its trailer/carrier. Use caution.
2) Familiarize yourself with the machine and its
controls.
3) Ensure the safety clutch control lever is in the
disengagedposition. The safety clutch
control lever is located on the left handle bar.
The disengaged position of the lever is down.
4) Remove the shaft locking pin located behind
the wheel axle. Store pin in hole provided on
left hand side of handle bar.
5) The wheel axle will now pivot. Lift up on the
handle to allowwheelaxle to pivot. For
transport, keep the wheel axle forward. When
cultivating, keep the wheel axle rearward for
added stability and control.
DO NOT transport the tillerwith the wheel
axle in the rear position.
6) Adjust depth shoe(ifequipped) by removing
shaft locking collarand slidingdepth shoe to
desired position. Replace shaft locking collar.
7) Open fuel shut-off valve. Set choke
control to Choke or Start position.
Set throttle control to Run or Fast
position. Set engine
stop switch to On or
Run position. Pull
starter cord rapidly.
Repeat (if necessary)
with choke off.
8) When in position to begingarden tilling,
engage the safety clutch controllever. The
tyneswillbeginrotating. Wheel axle must be in
the rearpositionwhile tilling.Release the
safety clutch controllever to stop the tynes
rotating. Tynespeed is governed by engine
throttle setting.
WARNING! –KEEPHANDSAND
FEET CLEAR OF TYNES AT ALL
TIMES!
9) Do not hurry the job. Proceed slowly and allow
the machine time to do the job. When ground
is extremely hard, reduce engine speed.
WARNING! –IN CASE OF DIFFICULTY,
DISENGAGE THE SAFETY CLUTCH
CONTROL LEVER. ALL TILLING ACTION
STOPS.Press the engine"STOP"button
located on the engine.
10) Stop Engine: Release the safety clutch control
lever.Move throttle to Slowposition. Set engine
stop switch to Stop or Offposition.DO NOT move
choke control to Choke
or Start position to stop
engine.Backfire or
enginedamagemay
occur.
AFTER USE
1) Turn fuelshut off valve to the "OFF"
position.
2) Allow machine to cool down.
3) Wash mud and dirt off of the garden tiller.
Ensure no water enters the carburettor.
4) Removeanyweeds,wire,rope or other
material thatmayhavewrappedaround the
tynes and rotor assembly.
5) Returnwheelaxle to forwardposition for
transport. Replace shaft locking collar.
6) Returndepth shoe(ifequipped) to full Up
position.
© Copyright 2001, Red Roo Sales & Service Company Pty. Ltd. 1301-0018
Commercial Environmental Equipment
SAFETYPRECAUTIONS
AND OPERATING
INSTRUCTIONS
™
GT622
GARDEN
TILLER
OPERATION
1) Remove the garden tiller
from its trailer/carrier. Use caution.
2) Familiarize yourself with the machine and its
controls.
3) Ensure the safety clutch control lever is in the
disengagedposition. The safety clutch
control lever is located on the left handle bar.
The disengaged position of the lever is down.
4) Remove the shaft locking pin located behind
the wheel axle. Store pin in hole provided on
left hand side of handle bar.
5) The wheel axle will now pivot. Lift up on the
handle to allowwheelaxle to pivot. For
transport, keep the wheel axle forward. When
cultivating, keep the wheel axle rearward for
added stability and control.
DO NOT transport the tillerwith the wheel
axle in the rear position.
6) Adjust depth shoe(ifequipped) by removing
shaft locking collarand slidingdepth shoe to
desired position. Replace shaft locking collar.
7) Open fuel shut-off valve. Set choke
control to Choke or Start position.
Set throttle control to Run or Fast
position. Set engine
stop switch to On or
Run position. Pull
starter cord rapidly.
Repeat (if necessary)
with choke off.
8) When in position to begingarden tilling,
engage the safety clutch controllever. The
tyneswillbeginrotating. Wheel axle must be in
the rearpositionwhile tilling.Release the
safety clutch controllever to stop the tynes
rotating. Tynespeed is governed by engine
throttle setting.
WARNING! –KEEPHANDSAND
FEET CLEAR OF TYNES AT ALL
TIMES!
9) Do not hurry the job. Proceed slowly and allow
the machine time to do the job. When ground
is extremely hard, reduce engine speed.
WARNING! –IN CASE OF DIFFICULTY,
DISENGAGE THE SAFETY CLUTCH
CONTROL LEVER. ALL TILLING ACTION
STOPS.Press the engine"STOP"button
located on the engine.
10) Stop Engine: Release the safety clutch control
lever.Move throttle to Slowposition. Set engine
stop switch to Stop or Offposition.DO NOT move
choke control to Choke
or Start position to stop
engine.Backfire or
enginedamagemay
occur.
AFTER USE
1) Turn fuelshut off valve to the "OFF"
position.
2) Allow machine to cool down.
3) Wash mud and dirt off of the garden tiller.
Ensure no water enters the carburettor.
4) Removeanyweeds,wire,rope or other
material thatmayhavewrappedaround the
tynes and rotor assembly.
5) Returnwheelaxle to forwardposition for
transport. Replace shaft locking collar.
6) Returndepth shoe(ifequipped) to full Up
position.
© Copyright 2001, Red Roo Sales & Service Company Pty. Ltd. 1301-0018
Commercial Environmental Equipment
SAFETYPRECAUTIONS
AND OPERATING
INSTRUCTIONS
™
DHS
HYDRAULIC POST
HOLE DIGGER
6. GETTING STARTED: Push machine tothe
location of the first hole. Start engine and allow to
reach operating temperature. Standing at the rear
of the machine at the control handle. To begin
digging a hole, pull the right hand side of the
control lever. This will cause the auger to turn in a
clockwise direction. Apply downward pressure to
begin digging the hole. If dirt remains in the hole
use an up and down motion toclear excess dirt.
Release the control lever tostop auger. To
reverse the auger rotation (counter-clockwise),
pull the left hand side of the control lever.
7. The amount of force exerted will depend on
the hardness and type of ground conditions.
8. Remember, the DHS is a single person operation,
designed for earth drilling. There may be holes that
will be extremely difficult,if not impossible, to drill.
9. If ground is too hard to drill or the auger is jamming
on ground conditions or foreign objects (eg. wire,
tree roots, etc.), the pressure relief will function,
stalling the auger rotation. Clear auger and start
again. The operator presence control will ensure
quick stop if hand is removed from control lever.
NEVER TIE OR JAM LEVER INTO THE ON
POSITION (FORWARD OR REVERSE).
REVERSE (COUNTER CLOCKWISE) MAY
BE REQUIRED TO UNSCREW JAMMED AUGERS.
10. Do not attempt to drill auger to full depth in one
operation. Continually clearing the hole in an up
and down motion will facilitate a much easier
drilling operation. It may be necessary to clear
cutters and auger flighting from time to time to
ensure quicker and easier cutting.
11. Remember, as in drilling a hole in steel, one needs a
sharp drill. Auger, teeth and pilot MUST be in good
condition if the auger is to work correctly. See wear
parts section for more information.
12. Auger motor head assembly may be
tilted as per incline when drilling on
slopes. DO NOT change the digger
position during drilling. DO NOT operate on a
slope that exceeds 15˚
13. DO NOT over reach. Ensure proper footing and
balance when working with this machine.
WARNING! –Keep hands and feet
clearof all moving parts at all times!
WARNING! –Keep hands and
feet clear of exhaust muffler during
or soon after operation.
14. WARNING! –in case of difficulty,
release the control lever to stop
the auger. All digging action stops.
Press the engine "STOP" button located on
the engine. (See illustration)
15. DO NOT OPERATE
CLOSE TO EDGES
OR EXCAVATIONS ETC.
CHECK FOR ELECTRICAL AND GAS LINES
BEFORE DIGGING
AFTER USE
1) Turn fuel tap to "OFF" position.
2) Allow machine to cool down. Wash mud
and dirt off of the hydraulic post hole digger.
Ensure no water enters the carburettor.
3) Remove any objects that may have wrapped
around the auger.
© Copyright 2012, Red Roo Sales & Service Company Pty. Ltd. 1301-0025-A
Commercial Outdoor Power Equipment
5.
a.
b.
STARTING THE ENGINE:
c.
d. Turning the engine switch
to the ON position.
To start a cold engine, move the choke
lever or choke rod (applicable types) to
the CLOSED position. To restart a warm
engine,leave the choke lever or choke
rod in the OPEN position.
Move the fuel valve lever to ON position.
Move the throttle lever away from
the MIN position,about 1/3 of the
way toward the MAX position.
RECOIL STARTER
Pull the starter grip lightly until you
feel resistance, then pull briskly.
Return the starter grip gently.
a.
Shut off switch on
console should be
used, not shut off
switch on engine.
b. Turn the engine switch
to the OFF position.
c. Turn the fuel
valve lever to the
OFF position.
16. STOPPING THE ENGINE:
Move the throttle lever
to the MIN position.
Some engine applications use a
remote-mounted throttle control
rather than the engine-
mounted lever shown here

9) NEVERoperate the hydraulic post hole digger
when fatigued. ALWAYS BE ALERT! If you get
tired while operating the hydraulic post hole digger,
take a break. If you have any type of physical or
mental condition that may be aggravated by
strenuous work, check with your physician before
you operate this equipment. NEVERoperate the
hydraulic post hole digger under the influence of
medication, alcohol or drugs.
10) ALWAYS KEEP YOUR HANDS, FEET
AND BODY AWAY FROM THE AUGER
WHILE THE MACHINE IS IN USE.
11) DO NOT leave the machine unattended while
the engine is running.
12) DO NOT overspeed the engine or alter the
governor settings. Excessive speed is
dangerous and will shorten engine life.
13) WARNING: Keep away from exhaust
muffler during or soon after operation.
14) NEVERoperate the hydraulic post hole
digger in an enclosed area. Engine
exhaust contains carbon monoxide, an
odourless and tasteless poison.
15) WARNING: Hydraulic oil is under
extreme pressure and can get under skin
and burn or poison. DO NOT operate
unit with leaking or faulty hose connections or
worn, cut hydraulic lines.
16) STOPthe engine and disconnect the
spark plug lead(s) and allow engine to
cool before inspecting or performing
maintenance on the hydraulic post hole digger.
17) REFUELLING
*Shut off engine. DO NOT REFUEL
AN ENGINE WHILE OPERATING!
*Allow engine tocool. Minimum 5 mins.
*USE UNLEADED FUEL ONLY. Use
clean, fresh unleaded fuel.
*Do not mix oil with unleaded fuel.
* Do not over-fill fuel tank. Allow space
for fuel expansion.
* Do not smoke near equipment.
* Allow no naked flame or hot material
in refuelling area.
* Use only approved fuel containers and
funnels. Remember, fuel is a potential hazard.
*Refer to engine owners manual for full details.
SAFETY PRECAUTIONS FOR DHS 9-5 USER
S
“STAY ALERT – DON’T GET HURT”
Engine
Exhaust
Pressure
Relief Valve
Lifting Point
Lifting Point
Digging Angle Adjustment
Foward/Reverse Handle
Operator Presence Control
Height
Adjustment
OPERATOR ZONE
DIGGING ZONE
Engine
Auger
safety
IS EVERYBODY’S BUSINESS
...now
safety
IS EVERYBODY’S BUSINESS
...now
safety
IS EVERYBODY’S BUSINESS
...now
safety
IS EVERYBODY’S BUSINESS
...now
USE COMMON SENSE
AND PLENTY OF IT
1) DO NOT allow any person to operate
the hydraulic post hole digger without
first reading and understanding the
safety precautions and operating instructions.
KNOW THE CONTROLS AND HOW TO STOP
THE HYDRAULICPOST HOLE DIGGER
QUICKLY IN AN EMERGENCY. RELEASE
CONTROL LEVERTO STOP AUGER.
2) NEVER allow children or untrained adults to
operate the hydraulic post hole digger.
3) ALWAYS wear
protective clothing
when operating the
hydraulic post hole
digger. This includes, but is not limited to: safety
glasses, hard hat, loose fitting gloves, steel
capped boots and hearing protection. NEVER
wear loose fitting clothing or jewellery when
operating the hydraulic post hole digger. Keep all
clothing away from moving parts. Items could
become caught in the machine, resulting in injury.
4) ALWAYS use hydraulic post hole digger in a
well lit area.
5) ALWAYS make certain the hydraulic couplings
are properly connected prior tostarting the engine.
6) NEVERoperate hydraulic post hole
digger on a slope that exceeds 15˚.
Digging holes on an incline is dangerous
and not recommended.
7) Police the area before
digging. Remove any
foreign objects in the
digging area eg bricks, rocks, wire and sticks.
Locate and mark any sprinkler heads, water pipes,
gas lines, electrical and telephone cables or any
other hazard either below or above ground.
8) DO NOT allow other persons near the
hydraulic post hole digger. It is up to
the operator tokeep bystanders and
animals a minimum of 6 metres away from the
machine while in operation.
SAFETY PRECAUTIONS FOR DHS 9-5 USER
OPERATING
INSTRUCTIONS
OPERATION
1. Familiarize yourself with the
machine and its controls.
2. The hydraulic post hole digger is designed to
dig vertical and selected offset holes.
3. Make sure the fasteners are properly secured,
hydraulic hoses properly connected, and digger
frame completely assembled prior to use
DO NOT ATTEMPTTO START ORRUN
ENGINE WITHOUT HYDRAULIC COUPLINGS
CONNECTED. DO NOT DISCONNECT
HYDRAULIC CONNECT QUICK COUPLINGS
WHILE THE ENGINE IS RUNNING.
4. Auger Installation a) Remove shaft locking
collar b) Insert Auger c) Replace shaft
locking collar.