Red Sea Max 130D User manual

Installation Instructions
MAX®130D Upgrade Circulation Pump
13
4
2
Familiarize yourself with the multidirectional outlet by disassembling
and reassembling it a few times.
When dry the nozzle does not rotate freely in the socket. Once
assembled in the aquarium it will move as required and will remain in
the desired position.
Insert the pump into the pump chamber
so that the threaded connector goes
through the hole on the right when
viewed from the front.
(picture shows view from the rear)
Assemble the Pipe set to the pump so
that the threaded connector for the outlet
nozzle is perpendicular to the pump as
shown in the drawing.
Ensure that the rubber washer is in place
on the connector.
Check that the pump is assembled correctly
and that the pump and power cable are
not damaged.
Screw the outlet onto the threaded
connector and tighten against the
glass. Initially adjust the nozzle to the
downward position.
Installation Instructions
MAX®130D Upgrade Circulation Pump
13
4
2
Familiarize yourself with the multidirectional outlet by disassembling
and reassembling it a few times.
When dry the nozzle does not rotate freely in the socket. Once
assembled in the aquarium it will move as required and will remain in
the desired position.
Insert the pump into the pump chamber
so that the threaded connector goes
through the hole on the right when
viewed from the front.
(picture shows view from the rear)
Assemble the Pipe set to the pump so
that the threaded connector for the outlet
nozzle is perpendicular to the pump as
shown in the drawing.
Ensure that the rubber washer is in place
on the connector.
Check that the pump is assembled correctly
and that the pump and power cable are
not damaged.
Screw the outlet onto the threaded
connector and tighten against the
glass. Initially adjust the nozzle to the
downward position.

Maintenance:
To ensure proper function the pump it should be cleaned on a
regular basis.
1. Unplug the power cord of the pump from the electric supply and
remove it from the aquarium
2. Remove the impellor chamber cover and take out the impellor.
3. Clean all of the parts, impellor chamber cover, impellor and the
impellor chamber of the motor by wiping with a soft cloth or brush.
To remove calcium carbonate deposits soak the parts in a week
acidic solution (vinegar, citric acid) until deposits have dissolved.
4. Rinse all parts thoroughly, reassemble the pump and return to
the aquarium before reconnecting the power cable to the electric
supply.
NOTE: Aquariums with higher levels of Calcium and Alkalinity will
require more frequent maintenance.
Troubleshooting:
If the pump stops working or makes mechanical noise, disassemble
and clean the pump as instructed above. If the pump makes mechanical
noise after cleaning replace the impellor. The impellor is a wear item
and may need to be replaced periodically.
Before carrying out this upgrade refer to
the safety instructions in the MAX®130
/ 130D
instruction manual.
1. The pump in this upgrade kit must be submersed
in water and is only for use in the MAX®130
/ 130D
aquarium. Operation without water can damage
the motor.
2. ATTENTION: Before doing any maintenance to
any appliance in the aquarium, disconnect the
power cord of the MAX®Power Center from the
wall outlet.
3. CAUTION: The MAX®Power Center must be
connected to a circuit that is protected by
a Ground Fault Circuit Interupter.
Installation Instructions
MAX®130/130D Upgrade Circulation Pump
Notice:
Maintenance:
To ensure proper function the pump it should be cleaned on a
regular basis.
1. Unplug the power cord of the pump from the electric supply and
remove it from the aquarium
2. Remove the impellor chamber cover and take out the impellor.
3. Clean all of the parts, impellor chamber cover, impellor and the
impellor chamber of the motor by wiping with a soft cloth or brush.
To remove calcium carbonate deposits soak the parts in a week
acidic solution (vinegar, citric acid) until deposits have dissolved.
4. Rinse all parts thoroughly, reassemble the pump and return to
the aquarium before reconnecting the power cable to the electric
supply.
NOTE: Aquariums with higher levels of Calcium and Alkalinity will
require more frequent maintenance.
Troubleshooting:
If the pump stops working or makes mechanical noise, disassemble
and clean the pump as instructed above. If the pump makes mechanical
noise after cleaning replace the impellor. The impellor is a wear item
and may need to be replaced periodically.
Before carrying out this upgrade refer to
the safety instructions in the MAX®130
/ 130D
instruction manual.
1. The pump in this upgrade kit must be submersed
in water and is only for use in the MAX®130
/ 130D
aquarium. Operation without water can damage
the motor.
2. ATTENTION: Before doing any maintenance to
any appliance in the aquarium, disconnect the
power cord of the MAX®Power Center from the
wall outlet.
3. CAUTION: The MAX®Power Center must be
connected to a circuit that is protected by
a Ground Fault Circuit Interupter.
Installation Instructions
MAX®130/130D Upgrade Circulation Pump
Notice: