Reddot Mobile R-888 User manual

BluetoothV3.0+EDRBluetoothV3.0+EDR
USER’S MANUAL
BLUETOOTH STEREO HEADSET
SPECIFICATIONS
Model NO BluetoothV.3.0+EDR
Bluetooth profiles HSP,HFP,A2DP,AVRCP Effective Range 10Meters
Music Time 6-8Hours Talk Time 7Hours
Standby Time Up to 65 Hours Input DC:5V/130mAh
Charge Time 3Hours Dimensions 14.5*10*6CM
About R-888
R-888 is a stereo headset with Bluetooth technology.It supports the following Bkyetooth profiles:
HSP-Headset Profile
HFP —— Hands-free Profile
A2DP—— Advanced Audio Distribution Profile
AVRCP——Audio/Video Remote Control Profile
Overview
1 Built-in microphone 2 3.5mm audio line
3 LED Indicator 4 +key:volume up/next song
5 Mulfifunction button:answer,and reject call,pause and play
6 -key:volume down 7 Charging port
(如下图)
Charging the battery with Micro USB cable
1
2
5
4
6
3
7

• Step1: Insert USB charging cable into USB port which have support 5V power
(such as AC/DC USB adapter or PC USB port)
• Step2: Connect charging cable to the charging port of headset.
• When the red light is on, the headset is in charging.
• When the red light is off, the headset is fully charged.
• It takes about almost 3 hours to charge the headset fully.
Warning:
• The battery is rechargeable.
• First time charging : first time charger battery ,please be sure the battery has been
charged fully before use.
How to use
1) Switching on / off headset
Functio
n
Operation LED indicator Voice
prompt
Switch
on
Press . ） button for 2
seconds, and release it till the
blue LED is on
Blue LED blink 3 times. Power On
Switch
off
Press .） button for 4
seconds, and release it till the
red LED is on
Red LED blink 3 times Power Off
Pairing the headset with Bluetooth devices
A. How to enter pairing mode
Function Operation LED indicator Voice
prompt
Enter pairing
mode
Make sure the headset is
off. Press and hold . ）
button for 6 seconds, and
release it till the red and
blue LEDS blink alternately
Red and blue LED
blink alternately.
Pairing
B. Pairing the headset with Bluetooth mobile phone
Please make sure your mobile phone has Bluetooth function that can be used.
Notes: Specific pairing procedures may vary with different mobile phone. Please refer
to your mobile phone manual for further information. Steps as follows:

• Please keep the headset and mobile phone in the range of 1 meter when
pairing.
• Make the headset enter into pairing mode (LED is red and blue blinking)
• Start the Bluetooth function of mobile phone and search for new Bluetooth
devices.
After searched, select “R-888”in the Bluetooth device list.
• According to indication, enter password or PIN No:”0000”, and press the key
of” Yes” or “confirmed”. ( it depends on the Bluetooth device setting )
• After successful pairing, select “R-888" in the Bluetooth device list, and
press “connect”.
• After connect successfully, the blue LED of the headset will keep blinking.
Notes:
• If the pairing is not successful, please switch off headset firstly, and then
re-pair again.
• After pairing is successful, paired devices will remember each other. Unless
pairing information is deleted because of new pairing, no need to pair when
use next time. If you want to pair the headset with other devices, please pair it
with the new device according to steps 1～6 mentioned above.
• Multilink technology allows simultaneous connection to two different devices,
just simply repeat the pairing process on both devices.
• Although WIN7 is a superior operating system with most drivers already
built-in, in some cases this does not cover the various hardware configurations
built into the device (e.g. PC, Note book, Net book etc) from the manufacturer.
In this case, please visit the manufacturer’s web site for the latest Bluetooth
drivers for your onboard Bluetooth device.
3) Re-connecting to a Bluetooth device
•Automatic connecting
Every time the headset is switched on, it will connect to last connected device
automatically, of course the source device Bluetooth must be on “on” states
•Manual connecting to last connected HFP device
When the headset is in standby mode and doesn’t connect to any HFP devices,
short press . ） button once, it will connect to last connected source device

automatically.
Notes:
- Before connecting to a Bluetooth device, please turn on the Bluetooth device’s
Bluetooth function.
- On some Bluetooth devices, take some Nokia mobile phones for example, you
have to allow automatic connecting in the mobile phone’s settings. Please refer to
your mobile phone’s manual for further information.
4) Making calls with the headset
Function Status of headset Operation
Voice dial Standby mode
Press and hold .） button for 1 second, release
it till hearing indication sound ,then speak the call
you want to.
Redial last
number Standby mode Short press .） twice quickly
Volume up Conversation mode Short press + key
Volume down Conversation mode Short press - key
Answer
calling Ringing Short press .）
Reject calling Ringing
Press and hold . ） button for 1 second, and
release until you hear indication sound
•Not all the mobile phones support all the functions listed above. Please refer to
the instruction of your mobile phone.
• Some functions and indication tones may vary with different mobile phones.
• When the volume is adjusted to max or min, you will hear a indication tone.
• For some mobile phones, when you press the key of accepting on the phone,
the conversation will be sent to the mobile phone. At this time, you can switch
the call to headset by using the conversation switch button or through
operating on the mobile phone. Please refer to the instruction of your mobile
phone for further information.
5) Playing music
When the headset connects with the mobile phone or Bluetooth transmitter , you
can enjoy music through headset wirelessly.
Function Status of headset Operation
Pause Playing music Short press .）

Play Pausing Short press .）
Next song Playing music Short press ▶▶▏ key
Last song Playing music Short press ▕◀◀ key
Volume up Playing music Short press + key
Volume down Playing music Short press - key
Notes:
• For some of mobile phones, when they are playing music, the music will
transmit to the speaker of mobile phone, you have to choose “transmit the
sound through Bluetooth” in the “setting” of music play interface, and then
choose “R-888” in the device list, the music will be transmitted to the
headset. Please refer to the instruction of your mobile phone for further
information.
• When the volume of headset is adjusted to max. or min, you will hear a
indication DU DU tone.
• Remote control the function of last song/next song/pause, it needs your mobile
phone or Bluetooth transmitter supports AVRCP. Please refer to the instruction
of your mobile phone or Bluetooth transmitter for further information.
6) LED
1) Battery Charging mode
LED indicator Status of the headset
Red LED is on Charging
Red LED is off Finish charging
2) Operation mode
LED Indicator Status of the headset
Red and blue LEDs blink alternately Pairing mode
Blue LED quickly blinks twice every 1 seconds. Not connected to a device
Blue and Red LED quickly blinks three times every 2
seconds
Set up HFP and A2DP
connection
Red LED blinks twice every 20 seconds Low power

Re-connecting to a Bluetooth device
A) Automatic connecting
Every time the headset is switched on,it will connet to the nearest,and last connected
device automatically.
B) Manual connecting to last connected device
When the headset is in standby mode and doesn’t connect to any device,short press .）
button once,it will connect to last connected device automatically.

FCC Information and Copyright
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
FCC RF warning statement: the device has been evaluated to meet general RF exposure
requirement , The device can be used in portable exposure condition without restriction.