RedNeck DELUXE RD-PLSTAIR-10 User manual

RD-PLSTAIR-10
REDNECK DELUXE 10FT STAIRWAY ASSEMBLY
INSTRUCTIONS
READ THESE INSTRUCTIONS IN THEIR ENTIRETY PRIOR TO ASSEMBLING THIS PRODUCT
WARNING! Do not remove, modify and/or omit any portion or otherwise mechanically
modify this product(s) or its assemblies in any manner. Modification, misuse and/or
part substitution shall immediately void your factory warranty. If you suspect that a
part(s) is missing and/or defective, immediately discontinue all use of the product and
contact Redneck Outdoor Products at 877-523-9986 for replacement of missing or
defective parts.
NOTE: Some parts of this product are manufactured to be universal in use, so there
may be some parts containing holes that will not be used in the assembly of this
particular model. To minimize confusion in the assembly process, please read these
instructions in their entirety before beginning.
Should you have any questions about the assembly, installation or use of this product,
or any other Redneck Outdoor Products, please call one of our customer service
representatives toll free at 877-523-9986.
1

FIGURE 1.1
TURN STAND PARTS INVENTORY
RIGHT CORNER HANDRAIL
QTY 2
LEFT CORNER HANDRAIL
QTY 2
LEG
QTY 4
WELDED PLATFORM ASSEMBLY
QTY 1
SMALL LEG STEM
QTY 4
LEG FOOT
QTY 4
CROSS BRACE
QTY 4
2

FIGURE 1.2
LADDER PARTS INVENTORY
UPPER LADDER
QTY 1
RIGHT ADAPTOR PLATE
QTY 1
TREAD ASSY.
UPPER LADDER
CONNECTOR PLATE
QTY 1
TREAD ASSY
QTY 1
LEFT ADAPTOR PLATE
LOWER LADDER
RIGHT ADAPTOR PLATE
LOWER LADDER
QTY 1
QTY 1
LEFT ADAPTOR PLATE
UPPER LADDER
LOWER LADDER
QTY 1
LANDING LEFT
LADDER FOOT
QTY 2
LANDING RIGHT
CONNECTOR PLATE
QTY 1
LADDER HAND RAIL
QTY 2
LADDER HAND RAIL
QTY 2
3

FIGURE 1.3
HARDWARE INVENTORY
ACTUAL SIZE
3/8" FLANGE NUT
QTY 75
3/8" x 2 1/4" CARRIAGE BOLT
QTY 19
3/8" x 1.00" CARRIAGE BOLT
QTY 42
3/8" x 3.00" CARRIAGE BOLT
QTY 12
3/8" x 2 1/4" FLANGE BOLT
QTY 2
4

8 - 3/8" FLANGE NUT
3/8" FLANGE NUT
8 - 3/8" x 2 1/4" CARRIAGE BOLTS
3/8" x 2 1/4" CARRIAGE BOLT
FIGURE 2.2
ASSEMBLE STEM LEG AS
4 - STEM LEGS SHOWN IN (FIGURE 2.2) REPEAT
PROCESS FOR OTHER 3 STEM LEGS.
PARTS & HARDWARE:
1 - PLATFORM
STEP 2: STEM LEGS AND PLATFORM
PLATFORM
STEM LEG
FIGURE 2.1
5

3/8" x 3.00"
CARRIAGE BOLT
3/8" FLANGE NUT
3/8" x 2 1/4" CARRIAGE BOLT
HANDRAILS + TOP BOLTS FOR STEM LEGS
FIGURE 3.2
ASSEMBLE RIGHT FRONT CORNER
STEP 3:
FIGURE 3.1
RIGHT CORNER HANDRAIL
ORIENT PLATFORM AS SHOWN.
NOTE: THIS IS ONLY SIDE WITH
4 HOLES IN THE SIDE
5 - 3/8" x 3" CARRIAGE BOLTS
10 - FLANGE NUTS
5 - 3/8" x 2 1/4" CARRIAGE BOLTS
PARTS & HARDWARE:
2 - RIGHT CORNER HANDRAIL
NOTE: DO NOT
INSTALL THIS BOLT
AS IT WILL BE DONE
IN A LATER STEP
6

3/8" x 3" CARRIAGE BOLT
3/8" FLANGE NUT
LEFT CORNER
HANDRAILS AS SHOWN
ASSEMBLE LEFT CORNER
:
FIGURE 4.1
HANDRAIL
STEP 4
LEFT CORNER
HANDRAIL
7 - 3/8" x 3" CARRIAGE BOLTS
7 - 3/8" FLANGE NUTS
PARTS & HARDWARE:
2 - LEFT CORNER HANRAIL
7

24 - 3/8" x 1" CARRIAGE
24 - 3/8" FLANGE NUT
4 - FEET
:
4 - LEGS
PARTS & HARDWARE
NOTE: IN THIS STEP ALL CARRIAGE
BOLTS ARE INSTALLED FROM THE
INSIDE WITH THE THREADS FACING
OUTWARD. THEREFORE THE FLANGE
NUT IS ON THE OUTSIDE MAKING IT
EASIER TO TIGHTEN WITH EITHER A
DRIVE SOCKET OR A WRENCH.
3/8" x 1.00" CARRIAGE BOLT
3/8" FLANGE NUT
FIGURE 5.3
FIGURE 5.1
FEET
LEG
PROCESS FOR THE OTHER 3 LEGS AND
FIGURE 5.2
FEET (FIGURE 5.3) AS SHOWN. REPEAT
STEP 5: LEGS & FEET
ASSEMBLE LEGS (FIGURE 5.2) AND
FEET
8

3/8" x 1.00" CARRIAGE BOLTS
3/8" FLANGE NUTS 8
4 CROSS BRACES
PARTS & HARDWARE:
8
NOTE: IN THIS STEP ALL CARRIAGE
BOLTS ARE INSTALLED FROM THE
OUTSIDE WITH THE THREADS FACING
INWARD. THIS IS TO INSURE THE
CARRIAGE BOLT IS SEATED IN THE
SQUARE HOLE IN THE CROSSBRACE.
3/8" x 1.00" CARRIAGE BOLT
3/8" FLANGE NUT
FIGURE 6.2
TO LEGS AS SHOWN IN FIGURE 6.2
ASSEMBLE CROSS BRACES
FIGURE 6.1
STEP 6: CROSS BRACES
9

3/8" 1.00" CARRIAGE BOLT
3/8" FLANGE NUT
3/8" 2 1/4" CARRIAGE BOLT
FIGURE 7.2
3/8" x 1" CARRIAGE BOLTS
3/8" X 1" CARRIAGE
BOLT
3/8" X 1" CARRIAGE BOLT
3/8" FLANGE NUTS
3/8" FLANGE NUT
3/8" FLANGE NUT
3/8" FLANGE NUT
3/8" x 2 1/4" CARRIAGE BOLTS
3/8" X 2 1/4" CARRIAGE BOLT
4
4
2 UPPER STAIR CONNECTOR PLATES
8
2 STAIR HAND RAILS
2 UPPER STAIR TO PLATFORM CONNECTOR
PARTS & HARDWARE
FIGURE 7.1
STEP 7: UPPER STAIR ASSY
ASSEMBLE UPPER STAIR ADAPTOR PLATES TO•
STAIR SIDE RAILS USING
AND . (FIGURE 7.2)
ASSEMBLE LANDING CONNECTOR PLATES TO STAIR•
SIDE RAILS USING AND
. (FIGURE 7.3)
ASSEMBLE HAND RAILS TO STAIR SIDE RAILS USING•
AND .
SEE DETAIL (FIGURE 7.2 & FIGURE 7.3)
LEFT UPPER STAIR
LEFT UPPER
STAIR ADAPTOR
PLATE
LANDING PLATFORM
CONNECTOR PLATE
HAND RAIL
RIGHT UPPER
STAIR ADAPTOR
CONNECTOR PLATE
PLATE
RIGHT UPPER STAIR
LANDING PLATFORM
STAIR SIDE RAIL
3/8" x 1.00" CARRIAGE BOLT
3/8" FLANGE NUT
3/8" x 2 1/4" CARRIAGE BOLT
FIGURE 7.3
10

MORE THAN 58" APART.
•
YOU WILL NEED 3 PEOPLE AND TWO 10ft A-FRAME STYLE LADDERS.
• PROCEED TO FIGURE 8.2
59" APART AS SHOWN IN FIGURE 8.1
ONCE CONNECTED THEY SHOULD END UP APPROXIMATELYNOTE:
START BY PLACING THE TURN STAND APPROXIMATELY 54" TO NO
STEP 8.1:
CONNECT 10ft STAND TO TURN PLATFORM WITH UPPER STAIR.
PARTS
1 10' STAND
1 TURN PLATFORM
1 UPPER STAIR
FIGURE 8.1
UPPER STAIR 10' STANDTURN PLATFORM
59" BETWEEN
THE FEET
APPROXIMATE
11

3/8" x 1.00" CARRIAGE BOLT
3/8" FLANGE NUT
FIGURE 8.2
EXTENSION
UPPER STAIR
NOTE: INSERT BOLTS FROM
BACKSIDE, THREADS TOWARD STAIR
PORCH
CONNECTING BRACKET
3/8" x 1.00" CARRIAGE BOLTS
3/8" FLANGE NUTS
3/8" x 1.00" CARRIAGE BOLTS
AS IT IS BEING LIFTED.SHOULD NOT STAND UNDERNEATH THE STAIR
THE 3/8" FLANGE NUTS AS SHOWN IN FIGURE 8.2
NEXT ASSEMBLE UPPER STAIR TO 10' STAND USING THE AND•
•
STEP 8.2
POSITION THE UPPER STAIR BETWEEN THE 10' STAND AND THE TURN PLATFORM ON THE GROUND. •
WITH TWO PEOPLE USING THE TWO 10' A-FRAME LADDERS ON EACH SIDE OF THE UPPER•
STAIR, GRAB THE UPPER STAIR ON EACH SIDE AND WALK IT UP THE LADDERS AND HOOK THE
CONNECTING BRACKETS OVER THE PORCH EXTENSION.
THE THIRD PERSON WILL NEED TO GUIDE THE BOTTOM PORTION OF THE STAIR UP AND ONTO THE•
TURN PLATFORM (RESTING THE LANDING BRACKETS, THAT ARE CONNECTED TO THE BOTTOM
OF THE UPPER STAIR, ONTO THE TURN PLATFORM LANDING.)
IMPORTANT! THIRD PERSON
HARDWARE
2
2
12

FIGURE 8.3
3/8" x 2 1/4" CARRIAGE BOLTS
3/8" FLANGE NUTS
LANDING CONNECTING
BRACKET
STEP 8.3
ADJUST POSITION OF TURN PLATFORM TO ALIGN HOLES ON TURN PLATFORM WITH THE•
HOLES IN LANDING CONNECTING BRACKETS ON UPPER STAIR.
ASSEMBLE THE UPPER STAIR TO TURN PLATFORM USING 3/8" x 2 1/4" CARRIAGE BOLTS AND•
3/8" FLANGE NUTS AS SHOWN IN FIGURE 8.3
HARDWARE
2 3/8" FLANGE NUTS
2 3/8" x 2 1/4" CARRIAGE BOLTS
13

3/8" X 1" CARRIAGE BOLTS
3/8" X 1" CARRIAGE
BOLT
3/8" X 1" CARRIAGE BOLT
FLANGE NUTS
3/8" FLANGE NUT
3/8" FLANGE NUT
3/8" FLANGE NUT
3/8" X 2 1/4" CARRIAGE BOLTS
3/8" X 2 1/4" CARRIAGE BOLT
PARTS & HARDWARE
2 LOWER PLATFORM CONNECTOR BRACKET
2 STAIR HAND RAILS
2 FEET
4
8
4
STEP 9: LOWER STAIR ASSY
ASSEMBLE LOWER STAIR ADAPTOR PLATES TO•
STAIR SIDE RAILS USING
AND .
ASSEMBLE FEET TO STAIR SIDE RAILS USING•
AND .
(SEE FIGURE 9.3)
ASSEMBLE HAND RAILS TO STAIR SIDE RAILS USING•
AND .
(SEE FIGURE 9.2)
ADAPTOR PLATE
FIGURE 9.1
HAND RAIL
STAIR SIDE RAIL
LEFT LOWER STAIR
RIGHT LOWER STAIR
ADAPTOR PLATE
3/8" X 1"
CARRIAGE BOLT
3/8" FLANGE
NUT
3/8" X 2 1/4"
CARRIAGE BOLT
FIGURE 9.2
PLATFORM
CONNECTOR
BRACKET 3/8" x 1.00" CARRIAGE BOLT
3/8" FLANGE NUT
FIGURE 9.3
FOOT
14

3/8" FLANGE
NUT
3/8" x 2 1/4"
FLANGE BOLT
ASSEMBLY
STAND
FIGURE 10.1
BRACKET
LOWER STAIR
CONNECTING
TURN
PLATFORM
3/8" FLANGE NUT
3/8" FLANGE NUTS
3/8" x 2 1/4" FLANGE BOLT
3/8" x 2 1/4" FLANGE BOLTS
2
1 LOWER STAIR ASSEMBLY
1 TURN PLATFORM STAND
2
PARTS & HARDWARE
STEP 10
WITH TWO PEOPLE (ONE ON EACH SIDE OF THE LOWER STAIR) LIFT THE LOWER STAIR
AND HOOK THE CONNECTING BRACKETS OVER THE TURN PLATFORM ALIGNING HOLES
AND ASSEMBLE USING AND AS SHOWN
IN FIGURE 10.1
15

95.381" O.D. STAND FEET
95.381" O.D. STAND FEET
217.256" OVERALL STAND
117.575" OVERALL STAND
63.067"
O.D. PLATFORM FEET
63.068"
O.D. PLATFORM FEET
107.692" O.D. PLATFORM & 5' STAIR
121.875" O.D. STAND FEET TO PLATFORM FEET
92.581" C/C STAND FEET HOLES
92.581" C/C STAND FEET HOLES
60.267" C/C HOLES
60.268" C/C HOLES
16

BOX 1:
Ladder, Handrails, Brackets
& Feet
RD-PLSTAIRS-5
NOTE: Can be used as a 5’ Stairway or
Bottom Section of a 10’ Stairway.
BOX 2:
Upper Stairway, Platform &
Handrails
RD-PLS-BOX 2
NOTE: To complete a 10ft Stairway,
BOX 1 (RD-PLSTAIRS-5), BOX 2 (RD-PLS-BOX 2)
& BOX 3 (RD-PLS-BOX 3) are requried.
BOX 3:
Legs & Braces for 10’ Stairway
RD-PLS-BOX 3
NOTE: To complete a 10ft Stairway,
BOX 1 (RD-PLSTAIRS-5), BOX 2 (RD-PLS-BOX 2)
& BOX 3 (RD-PLS-BOX 3) are requried.