RedPlate BlackVerbDue User manual

RedPlate BlackVerbDuo Operations Guide
1
BlackVerbDuo
Operations Manual
Welcome to the RedPlate Family, thank you for your purchase of a RedPlate
BlackVerbDuo amplifier. Please take a moment and review this manual for an understanding
of all the available features (or just put all the knobs at noon and play).
This Manual applies to BlackVerbDuo models produced after 01/21/2012. Check the
Addendum Section for model differences.
Signal Path Block Diagram:
FRONT PANEL:
Input Jack –Typical High impedance input to the amplifier. Designed to be “Pedal Friendly” in
the unlikely event you will ever use a pedal in front of the BlackVerbDuo.

RedPlate BlackVerbDuo Operations Guide
2
CLEAN PREAMP SECTION
The Clean Preamp is designed to imitate (and surpass) all of the “classic” guitar amp preamps.
The BlackVerbDuo gives the player the ability to do two unique things:
1. Shift the midrange center point frequency.
2. Select the amount of Bass gain appropriate to your guitar choice (via Humbucker/Single coil
switch covered in the Rear Panel Section of this manual).
Bright Switch –Center = OFF, Down = sound of new strings, Up = normal Bright response.
Volume –Typical setting is between 3 and 5 but experimentation is encouraged. Pulls to
switch the Tweed Boost to a more conventional Mid Boost (this topic is covered in the Other
Features Section of this manual).
Treble Control - Adjusts highs (also upper midrange when the Tweed Boost is engaged).
Middle Control –Controls the amount of Midrange frequencies, somewhat interactive with
the Bass Control. Pulls to enable “Deep” which scoops some midrange frequencies and
emphasizes Bass (makes your electric sound more like an acoustic).
Bass Control –Sets the amount of low end. Can be rotated to zero where it clicks off for a full
tone stack lift.
Mode Selector –A six position rotary switch, it steps through 5 progressively fatter positions of
the midrange center frequency and achieves maximum fat midrange by engaging Tweed Boost in
position 6 (see the Other Features section of this manual for details).
EDGE DRIVE SECTION
The EDGE Drive section is used to add character to the clean tone. The section’s range of
effect can be just a hint of early break up or a full on aggressive heavy metal rock style distortion.

RedPlate BlackVerbDuo Operations Guide
3
Gain Control –Bypasses the section when rotated to zero, this control sets the amount of
signal for the first gain stage of the section. Low settings are smoother and higher settings are
more aggressive.
Drive Control –Sets the amount of distortion by controlling the level between the 2 gain
stages of the section.
Level Control –Sets the output volume of the section. Higher settings are “bigger” and more 3
dimensional.
BODY DRIVE SECTION
The BODY Drive section can also add character to the clean tone. The section’s range of effect
can be just a hint of early break up to full on aggressive distortion.
Gain Control –Bypasses the section when rotated to zero, this control sets the amount of
signal for the first gain stage of the section. Low settings are smoother and higher settings are
more aggressive.
Drive Control –Sets the amount of distortion by controlling the level between the 2 gain
stages of the section. Pull this control to shift into more gain and girth for the distortion.
Level Control –Sets the output volume of the section. Higher settings are “bigger” and more 3
dimensional. Pull this control to engage a high frequency roll off.
MASTER SECTION
Reverb Control - Sets the amount of reverberation effect, takes the reverb out of circuit when
rotated to zero (there will be a slight volume and tone change).
Presence Control –The presence circuit uses global negative feedback to remove low
frequencies which frees up bandwidth for more midrange and highs. Think of it as a tone control to
balance the relationship between highs and lows, especially when the amplifier is naturally

RedPlate BlackVerbDuo Operations Guide
4
producing increased low end at louder volumes. The control clicks off when rotated to zero for no
presence.
Master Volume –This is an active control and actually adds gain at the higher settings. The
cleanest tones are achieved at settings below 7.
REAR PANEL SECTION
Domestic (USA):
Rear Panel Export:
IEC Module –contains the main power switch, power cord inlet connector and the fuse drawer
which doubles as the voltage selector on export models. To access the fuse(s) use a small flat
blade screwdriver in the notch at the bottom of the power cord inlet connector, the drawer snaps
out in a rearward direction. The BlackVerbDuo can accept both the larger (3AG footprint) or smaller
European (5mm X 20mm) fuses. A time delay variety (SLO-BLO) is recommended. Follow the
recommended amperage ratings on the panel. The fuse drawer can be rotated on the export
models for voltage selection, make sure the correct value fuse is located on the same side of the
fuse drawer as the desired selection arrow. Line up the appropriate arrow on the fuse drawer with
the arrow on the bottom right of the module for the proper VAC selection.
Standby Switch –This switch allows the tubes to warm up before operating the amplifier. Wait
1 minute after power on to move it up to the operate position. For improved tube life and
performance do not leave the amplifier in Standby position for longer than 20 minutes (better to just
leave it in operate mode during performance intermissions).
50 WATT / 40 WATT Switch or Fixed/Cathode Switch –(2 6L6 models) This switch changes
the bias architecture of the output tubes from fixed bias (50 WATT) to cathode biased (40 WATT).
The 40 WATT position allows the use of 6V6 tubes for less power output (~18 Watts with 6V6).
Bias adjustment and bias test point –Allows external access for bias adjustment (see bias
procedure in the Maintenance section).
Impedance Selector Ω - Set this to the total impedance of all attached speakers. When 6V6
tubes are used, set to the next lower number (50 Watt 2 6L6 models only).
Speaker Jacks –The MAIN and EXT jacks are wired in parallel. The MAIN jack must be used
first because it has a protection device. ALWAYS HAVE A SPEAKER CONNECTED TO AVOID
PERMANENT AMPLIFIER AND OUTPUT TUBE DAMAGE.
LINE OUT –A line level signal jack derived from the speaker output which contains the whole
tone of the amplifier. Example usage would be for recording or connection to a PA or slave amp.

RedPlate BlackVerbDuo Operations Guide
5
SEND and RETURN Jacks –The send jack connects to the input of an external effects device
and the return jack connects to the output of an external effects device. The return jack interrupts
the signal path so the external effects unit must mix the wet and dry signals.
Footswitch Jack - This is a standard 180 degree 5 pin DIN jack for footswitch connection. If a
replacement cable is needed, make sure all 5 wires are supported. The pinout is conveniently
located on the rear panel for use with automated switcher conversion boxes.
SMOOTH Switch –Employs local negative feedback in the clean preamp for a hint of
compression.
Humbucker / Single coil Switch –Sets the amount of bass gain in the input stage, useful for
matching the amplifier to the guitar type.
OTHER FEATURES
The BlackVerbDuo comes complete with a 4 button footswitch and a footswitch cable. The
cable used is a regular MIDI cable and is readily available in any length at most music stores.
FOOTSWITCH
TWEED –Midrange Boost feature. When engaged the size of the treble capacitor is increased
to allow for more upper midrange, at the same time it does a lift of the midrange control for
maximum midrange. The effect can be lessened by pulling the front panel Volume control which
eliminates the midrange control lift. The footswitch button does not work when position 6 of the
rotary MODE switch on the front panel is selected because it is a duplicate function.
EDGE –Character Boost feature. When lit, the Drive section of the amplifier is active, not lit,
means the section is bypassed. The footswitch button does not work when the front panel EDGE
Gain control is rotated to zero because it is a duplicate function.
BOOST –Girth Boost feature. When lit, adds volume and tone by doing a partial tone stack lift.
The footswitch button does not have any affect when the front panel Bass control is rotated to zero
because it is partially a duplicate function.
BODY –Overdrive Section. When lit, the Body section of the amplifier is active, not lit, means
the section is bypassed. The footswitch button does not work when the front panel BODY Gain
control is rotated to zero because it is a duplicate function.
THE EDGE AND BODY SECTIONS CAN BOTH BE ENABLED FOR EVEN MORE GAIN.
POWER ON/OFF PROCEDURE

RedPlate BlackVerbDuo Operations Guide
6
1. Check the Standby switch to make sure it is toggled downward for Standby operation (the
Standby switch is located just to the right side of the power cord/IEC).
2. Toggle the main power switch to the up position (this switch is located at the top of the IEC
input module). The front panel pilot light should be lit.
3. Wait one minute and then toggle the Standby switch upwards to the Operate position.
4. POWER OFF –Toggle the main power switch downward, there is no need to go into
standby first although it will not hurt anything.
MAINTENANCE SECTION
Your BlackVerbDuo amp has been designed for years of trouble free operation. The vacuum
tubes will need to be replaced over time. We recommend new output tubes every 160 - 240 hours
and new preamp tubes every 320 - 480 hours.
The front and rear panels have a protective finish that can be easily scratched with abrasives
so always use a damp soft cloth to clean them (never use paper towels). The cabinetry can be
cleaned with our super secret tolex cleaner (on a paper towel - 2 squirts of WD-40 and 4 squirts
window cleaner), let your keyboard player try it on his plastic keys, it replicates the feel of a brand
new keyboard.
TUBE LAYOUT
All tube brands are acceptable, a long plate is preferred in the V7 (Phase Inverter) position.
Warning –No user serviceable parts inside so unless you know what you’re
doing please refer to a qualified service person only.
BIAS PROCEDURE
1. When new output tubes are installed it is important to re-bias the amp for optimal
performance. No biasing needed for 6V6 tubes because they can only be used in cathode
bias position.(50 Watt 6L6 amp only)
2. ALWAYS HAVE A SPEAKER CONNECTED.
3. Use a digital volt meter set to DC volts at lowest scale (MV). Makes sure the black lead is
the common terminal of the meter and the read lead is the DC voltage terminal of the
meter.
4. Place the Amplifier in operate mode with the Master Volume and Reverb controls set to
zero.
5. Set the 50 WATT/ 40 WATT switch to the 50 WATT position. (ex. 50 Watt 6L6 amp)
6. Place the red meter lead in the test point hole (red tip jack) And touch (or clip) the black
meter lead on one of the metal output tube retainer clips.

RedPlate BlackVerbDuo Operations Guide
7
7. Use a small flat blade screwdriver to adjust the bias pot for a reading to match the
recommended value printed on the rear panel ± 5 MV . The reading is the sum of the idle
current for both tubes.
8. Recheck the reading after 10 minutes of operation, and again after a week or two of
operation.
INTERNAL TRIM POT
The BlackVerbDuo has an internal trim pot for the Phase Inverter tube balance –Useful for
working with unmatched 12AX7 tubes in the phase inverter position. Refer to qualified personnel
for proper setting.
ADDENDUM
Re: Model BlackVerbDuo88 (with 80 watt KT-88 output section) and BlackVerbDuo24 (6V6
output section)
This manual is applicable for the above 2 models with the following changes:
1. BVD88 can use 6L6GC with no change in the impedance selector. (see note)
2. BVD24 is output tube type 6V6 only. (see note)
NOTE: Observe the Bias settings and Fuse ratings written on the rear panel(s) for operating
and biasing these amps.
RedPlateAmps Warranty
At RedPlateAmps we pride ourselves making products that are built to last. The workmanship in
your RedPlate amplifier is warranted to be problem free for the lifetime of the original owner, or in
the event of resale a onetime transfer to a new owner for coverage for 3 years from the original
manufacture date (please inform us of an ownership change to insure coverage). The actual
electrical components in your amplifier are warranted for a period of 3 years. Exclusions are
vacuum tubes, reverb tanks, cables, speakers and cosmetics which are warranted for 30 days.
Improper handling or product misuse or product abuse or unauthorized repair work or
unauthorized modifications may nullify your warranty. Eligibility for coverage and covered items
are at the sole discretion of RedPlateAmps.
RedPlateAmps
1812 W Cinnabar AVE
Phoenix AZ 85021
www.RedPlateAmps.com
email: [email protected]m
Thanks again for joining the RedPlate Family –Henry
Blank Template:
Copy or print the next page to record your own favorites. Once you’ve zeroed in on your
signature setting please email the completed template to [e-mail] –we may
include your favorite in the online version of this manual.

RedPlate BlackVerbDuo Operations Guide
8