REED R450+ Chain Vise Tripod User manual

1A R450+ Base with Wear Plate and Screws 99050 41170 / 72097* —
1B R470+ Base with Wear Plate and Screws 99403 — —
——15099esaBmooRnaelCC054RC1
2 X-7002-B5190425099ylbmessAyarT&geL
3 T 844-C0421440099yarTloo
4 Tray Support Clamp w/screw & nut 99054 41235 D-488-X
5 W 9331-E5590422099etalPrae
6 Screw for wear plate (2) 5 Pk=99069 39002 40960 E-75-X
7 868-E076647810308099=kP5)3(tloBgeL
8 4901-E522442300317099=kP5)3(tuN
9 Lock Washer (5) 5 Pk=99072 30033 40930 E-1095
X-5731-E5621435099)6(srehsaW"X"/w)3(sniPyarT01
11 "X" Washers (6) 5 Pk=99073 99010 41270 E-1377
X-5831-E5521475099)2(ylbmessAgeLtnorF21
X-9831-E0521485099ylbmessAgeLraeR31
——38104pirGeldnaH41
X-4441-E5490455099ylbmessAniahCgeL51
——5209957099=riaP)2(swaJ61
Ref. Description REED (pack) REED
N/PdlO.oNtaCedoCmetIedoCmetI.oN
A
A
1C
11
15
5
617
8
9
29
29
4
14
16
26
25
17
24
23
28
22
21
18
20
12
10
13
16C or 16P
30C
27
3
19
2
Chain Vise Tripod (R450+, R45OC, R45OP, R470+)
Replacement Parts
Capacity: 1/8" Through 6"
Parts List
Ref. Description REED (pack) REED
N/PdlO.oNtaCedoCmetIedoCmetI.oN
ININ8209967099=riaP)2(C054RC61
3209977099=Pair)2(P054RP61
17 Jaw Screws & Nuts (2) 5 Pk=99059 99084 NI NI
ININ70029eldnaH81
X-1713-E0501406099ylbmessAwercS&eldnaH91
ININ16099rehsaW&tuNhtiweldnaH02
ININ42099rehsaWtsurhT12
ININ02099wercSniahC22
ININ65029niPrelloR32
8842-E0990401029relloR42
—*29027/5701431099ylbmessAniahC52
1872-E0401422129niPwercSniahC62
—*20127/0321446099ylbmessAwercSkcaJ72
3874-E0561363439niPgnikcoLtuN82
29 Grommet (3) 40171 40940 F-532
30C R450C Chain Cover for clean rooms 99030 — —
Replaces Ridgid®
Replaces Ridgid®
Patented
NI - Not Interchangable with Ridge Tool Co. parts. ® Ridgid is a registered trademark of Ridge Tool Co.
*First number is for Ridgid 450, second number for Ridgid 460.
R450+
R470+

R450+ & R40+ Series Tripods
Operation & Instructions For Assembling Legs & Tray
R450+ Chain Vise Tripod
R450P Plastic Pipe Tripod
R450C Clean Room Tripod
R40+ Yoke Vise Tripod
R470+ Chain Vise Tripod
Patented
1) For easier assembly, place the base upside down on a flat surface.
2) Insert rear leg in base with foot pointing outward as shown. Secure to base with bolt, nut, and washer. Tray support is pre-
set with a clamp collar for approximate position and is adjustable. (see "Tray Adjustment" note below).
3) Insert front legs so feet are pointing outward and secure to base with bolts, washers, and nuts.
4) To assemble tray, open tray so that side of flanges are facing bottom of base. Attach the rear leg first with tray pin
then proceed to front legs.
5) Push "X" washers in pin grooves and pinch long ends together with pliers.
6) Stand tristand on legs. If you have a yoke vise tripod, assemble yoke to base. The hook on the yoke can either be
on the right or left side depending on operator.
Operation and Maintenance
JAWS — To renew teeth—remove jaw screws and nuts, rotate jaws in either direction, replace jaw screws and nuts and tighten.
TRAY ADJUSTMENT— If folding tray does not snap into position and hold legs rigid when tripod is set up, loosen
clamp screw in rear leg tray support and slide support clamp upward — tighten clamp screw securely.
JACK SCREW — Used with a length of 1" pipe as an adjustable ceiling brace to anchor tripod, but for large heavy
pipe, fasten feet of tripod to floor securely.
BENDERS — Place pipe, conduit, or tubing into holes provided on base and pull down into grooves.
HANDLE GRIP — To install new handle grip over top of rear leg, insert compressed air hose nozzle under bottom edge
and pull down while expanding with air flow.
LUBRICATION — Perodically lubricate the tray hinge, vise screw, jack screw, and chain with oil or spray silicone.
Replacement Parts Assembly
A
A
BASE
FOOT
6" PIPE REST
HANDLE GRIP
TRAY PIN
TRAY
BOLT, NUT &
WASHER
BENDING
GROOVES
VISE SCREW
SUPPORT CLAMP
CHAIN
CHAIN
CLAMP SCREW
"X" WASHER
JACK SCREW
REAR LEG
ADJUST CLAMP
RUBBER OPTIONAL-
ROTATE TO RENEW TEETH