REED Muse3C User manual

Reed
Muse3C
turntable
User manual

Figure 1
1. Put the box into position shown by
the markings on the side of the
packaging. (Figure 1).
Figure 2
2. Unbox the turntable while reading
the User Manual. (Figure 2).
Figure 3
3. Take out the top packaging layer
(Figure 3).

Figure 4
4. Take out all the accessories except
the big box. (Figure 4).
Figure 5
5. Take out the turntable platter.
(Figure 5).
Figure 6
6. Take out the middle layer of
packaging (Figure 6).

Figure 7
7. Take out the big cardboard box
(Figure 7).
Figure 8
8. Take out the turntable and put it to
a designated place close to
dedicated audio equipment (Figure
8).
ATTENTION! Turntable is heavy
(25 kg / 55 pounds), so don’t
hesitate to ask your friend for help.
Figure 9
9. When ordering friction drive option
(Figure 9),
a) unscrew transportation screws
(with red caps) for both motors
b) check if motor levers can move
freely

Figure 10
c) check if Belt / Friction switch is
set to Friction position, if not –
set it to Friction (Figure 10).
Figure 11
10. When ordering belt drive option (Figure
11):
a) check if levers of both motors are
securely fastened by transportation
screws (red caps); if not, fasten it by
hand
b) take a belt from the box and put it on
the pulleys of both motors and the
drive wheel (Figure 11)
Figure 12
c) check if Belt / Friction switch is set to
Belt position, if not –set it to Belt
(Figure 12).
Link to view how to change transmission
options from belt to drive (and opposite):
https://www.youtube.com/watch?v=ijYZlNEBO
60

Figure 13
11. Put the platter on the turntable axis
(Figure 13).
Figure 14
12. Dot-marks on the turntable platter and
axis must be aligned (Figure 14).
Figure 15
13. Connect the power supply to a turntable
and plug it into a power socket:
- 220V –240V, 50Hz or
- 110V –130V, 60Hz (on request).
14. After connecting turntable to the power
source:
a) red-colored LED next to 0is turned on
(Figure 15).

Figure 16
b) green light appears through the disc
holes (Figure 16)
Figure 17
c) any combination of LEDs in the
inclinometer (digital level) is turned
on (Figure 17).
d) to toggle turntable inclinometer
between on and off, please press the
"0" button and the "33" button at the
same time.
e) inclinometer is not operation when
platter is moving.
Figure 18
15.By adjusting turntable feet up or down,
set the turntable to a horizontal position,
i.e. until all level LEDs will come off
(Figure 18). LEDs next to arrows show
the direction of adjustment (up or down)
of the left or right foot.

Figure 19
16. Turntable is turned on by pressing
appropriate turntable speed button (33 or
45). Then:
a) red LED 0goes off and green LED
turns on next to selected speed
button (Figure 19),
Figure 20
b) platter rotation stability is
indicated by steady green-lit hole
pattern (Figure 20)
c) if platter does not start to move or
its rotation is obstructed, after 5
seconds turntable turns off; if
rotation speed is unstable, both
green and red speed LEDs are on at
the same time.
Figure 21
17. Tonearms (one or two) are mounted by
using protractor (Figure 21).

Figure 22
18. Tonearm mounting position, depending
on its length, is changed by turning
(relatively to each other) two tonearm
mount base discs –outer (big), which is
fixed using a screw (Figure 22) and inner
(small), depicted in Figure 23. For a
screw fastening please use s=1,5mm hex
(Allen) key (included).
Figure 23
19.To mount tonearms with different
mounting patterns, please use different
inner tonearm mount base discs (small).
20.If turntable is not used for more
than 7 minutes, it goes to sleep
mode –just the red 0 LED indicates
that turntable is connected to the
power supply. Turntable returns to
operation mode after pressing any
of the buttons or moving the
platter.
21.To toggle turntable speed indication
(green light from under the platter)
between on and off, please press the "0"
button and the "45" button at the same
time.