Regent Lighting Solutions Sliver Bollard User manual

1
www.regentlight.co.za
INSTALLATION INSTRUCTIONS
ALL CONNECTIONS TO BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
ALL CONNECTIONS TO BE CARRIED OUT BY A QUALIFIED ELECTRICIAN
1
PLEASE READ CAREFULLY BEFORE STARTING INSTALLATION.
PLEASE READ CAREFULLY BEFORE STARTING INSTALLATION.
Regent Lighting reserves the right to change specifications modify designs
and discontinue items without incurring obligation and whilst every effort is
made to ensure that descriptions, specifications and other information in
this catalogue are correct, no warranty is given in respect thereof and the
company shall not be liable for any error therein.
WARNING: TO AVOID FIRE, SHOCK OR DEATH
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS
OFF BEFORE WIRING
ALL LUMINAIRES SUPPLIED AND TO BE INSTALLED ABOVE AND BELOW 5 METERS
ARE IN COMPLIANCE WITH SANS 60598 SECTION 3.5.6 ACCORDING TO THE
MANUFACTURER GUARANTEE AND WARRANTY
Electrical products can cause death, injury, or
damage to property. Installation of this
product must be carried out by a qualified
electrician, in compliance with SANS 10142 or
corresponding regulations of the country of
installation. On completion of installation, the
Certificate of Compliance must be updated.
Sliver Bollard - Plinth Mounted
Electronic Control Device
WARNING
Electronic Control Device
WARNING
3 - 13 MAIN REEF SERVICE ROAD, CORNER
SPRINGBOK AND MAIN REEF ROAD, INDUSTRIA,
JOHANNESBURG. SOUTH AFRICA.
TEL : [phone]
www.regentlight.co.za
RE GENT L I GHT ING A D IVIS ION OF WAH L
IN DUST RIES.
DO NOT CONNECT THE FITTING LIVE
November 2017
Requirements:
Be sure the electricity to the system you are
working on is isolated.
If the main supply power (live) is on, it will cause
damage to the luminaire.
1. Ensure the pole is installed correctly.
A. Ensure the electrical cable is fed through the 250mm deep
hole.
B. Insert and secure the bolt cage into the hole and feed the
electrical cable through the bolt cage towards the surface,
ensuring the cable is fed parallel to the pathway.
C. Feed the cable through the stubby to the cable joint kit.
Save These Instructions for Future Reference
Save These Instructions for Future Reference
ELECTRIC SHOCK
HAZARD
This equipment is to be
serviced by trained
personnel only.
ELECTRIC SHOCK
HAZARD
This equipment is to be
serviced by trained
personnel only.
Sliver Bollard - Plinth Mounted
Ground Level
Bolt Cage
Stubby
LIGHT SOURCE
LIGHT SOURCE
Ground Level
DO NOT PLUG
(CONNECT) WHEN
LIVE AS IT WILL CAUSE
DAMAGE TO THE
LUMINAIRE. A
B
C
5
5. Switch on the power
supply.
250mm
390mm
25mm

www.regentlight.co.za
www.regentlight.co.za
2
7
8
3
4
This product should be installed by a competent person i.e. Qualified electrician.
This product requires a constant stable electrical supply 220V - 240V VAC 50Hz - alternating current.
The product must be regularly maintained, including the replacement of lamps/LED timeously.
This product could be HAZARDOUS if not used correctly, it could cause electric shock, serious bodily harm or death.
This product is not a toy, please keep away from children.
This product may contain small parts that can be swallowed.
Use only the correct light bulbs/LED as stipulated on the carton for the product.
Any modifications of this product after supply will result in the guarantee being void.
Spare parts may become unavailable over time.Items can vary slightly from the picture on the carton
Coastal humidity can affect the longevity of the light fitting over time.
Be sure to follow the steps in the order given.
Read instructions carefully.
Important Safety Instructions
4. A. Slide the fitting onto the
stubby already secured to the
bolt cage.
B: If the mounting positions
provided are not sufficient
according the ground/surface
level, drill the extrusion, using
the mounting holes as a
reference.
Ensure that there are no
exposed conductors, loose
strands or trapped/pinched
insulation.
C. Align and fasten the fitting
to the stubby through the
selected mounting holes,
using the 4 stainless steel bolts
supplied.
D. Slide in gear tray and
diffuser.
E. Align and fasten the end
plate, ensuring the gasket is
securely in place.
F. Finish the ground/surface as
desired.
Ensuring the surface does not
intersect the fitting.
Ensure the finished floor is
level.
2. Ensure the cable is fed through the bolt cage and
stubby.
Ensure that there are no exposed conductors, loose
strands or trapped/pinched insulation.
Ensure that the stubby is installed in the correct
position/direction, and is installed at the correct level
according to the ground/surface & is correctly
aligned to the base.
Using the electrical cable from the bolt cage, fed
through the stubby A. connect the electrical supply
tail from the bollard B. to the IP rated cable joint kit.
SWITCHED LIVE – (Red or Brown) to terminal marked L
NEUTRAL – (Black or Blue) to terminal marked N
EARTH – (Green/Yellow) to terminal marked
C. Connect the electrical cables in the IP rated
cable joint kit.
D. Pour epoxy resin into the cable joint in the opening
and allow to set, refer to instructions on the epoxy
resin bag. Once completed align and fasten the lid
to the cable joint.
E. Once connected and the resin has cured, push
the cable joint into the bollard extrusion.
3. A. Loosen and remove the end plate on the
top of the fitting through the four stainless steel
fasteners.
B. Slide out the diffuser from the fitting on both
sides.
C. Slide out the gear tray with the light source
from the fitting.
A
B
C
Mains to
Luminaire
Earth Loop
Green/Yellow
Switch
Wire Red
Neutral loop
Black or Blue
(L) Brown
(E) Green/Yellow
(N) Blue
DO NOT PLUG
(CONNECT) WHEN
LIVE AS IT WILL CAUSE
DAMAGE TO THE
LUMINAIRE.
C
A
B
D
Cable Joining kit
Stubby
E
A
D
E
OPTION 1 OPTION 2 OPTION 3
1
2
3
50mm
B
C
70mm 90mm
Finish the
floor
F
Finished Floor Level
Ground Level
Finished Floor Level
390mm
25mm
25mm
Ground Level
FFL
FFL
iiiiii