Rehabmart SAT-1065 User manual
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
3. PRODUCT STRUCTURE
Motion Sensor User Manual
SAT-1065
·
·
·
·
·
·
(1) Power on (battery or USB).
(2) Install the sensor's holder in desired lth crews or 3M glue.
(3) Insert the mulnto its holder.
LED INDICATOR MICRO USB PORT BUTTON
Definition of LED Indicator
AP Mode LED indicator blink slow in red
EZ Mode LED indicator blink fast in red
Bun Instruction
In the network
Press and hold the Button for 5s then release,
resume to default set, then it enters into
EZ inclusion mode
Out of the
network
Press and hold the Button for 5s then release
to switch EZ/AP mode
Note:
1. In the network: Device has been included into the network.
2. Out of the network: Default seter configured for Wi-Fi
40mA
40uA
Battery Capacity
Dettance 8m
Det
2.4 GHz-2.484GHz
IEEE802.11b/g/n
Power Supply
4. Specifications
6V 2*CR123A or 5V 1A USB DC power
Working current
Standby current
1300mAh
120°
Wireless transmit
receiving frequency
Network protocol supported
5. INSTALLATION 6. Download app
7. Add Devices
WEP/TKIP/AES,WPS
En
2
3 4 6 7 8
9
5
11
Transmit
R
Working temperature
Storage temperature
Re humidity
-10 ~ +40℃
-20 ~ +60℃
8～80%RH
10 12 13 14 15 16
1. PRODUCT OVERVIEW
SAT-1065 is a Wi-Fi based PIR sensor. You can check the device
via APP when it detects someone moving within the
2. PRODUCT FEATURES
7.2 Add the device to the network.
EZ Mode
Power on, the red LED indicator will blink fast, then enter the EZ
mode. Click the "Confirm indicator is blinking rapidly ", and click
the “Next”, it will add device, once it is connected successfully,
click “Done” upper right and switch to the device main interface.
8. Delete devices
8.1 Click the upper right on the device main interface, and click
“Remove Device”, select “Disconnect” and then click “Confirm” to
remove this device from APP. Select “Disconnect and wipe data”
and then click “Confirm” to remove this device from APP and all
related data will be wiped.
finished.
6.1 Scanning following QR codes to download APP for Android and
IOS System
AP Mode
Mode” upper right, click "Confirm the indicator is blinking slowly "
and click the “Next”,then click “Go to Connect”.
12. FCC NOTICE
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including
The manufacturer is not responsible for any radio or tv interference
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
generates, uses and can radiate radio frequency energy and, if not
If this equipment does cause harmful interference to radio or
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
6.2 Start the APP and register an account with your email address
then login APP with your account;
Open the APP and type your mobile number or email address, and
；
methods for Wi-Fi inclusion, EZ and AP;
Compliant with CE,FCC and RoHS；
；
；
；
802.11b: +14dBm@ 11Mbps
802.11g: +13.5dBm@ 54Mbps
802.11n: +13dBm@ MCS7_HT20
802.11b: +17dBm@ 11Mbps
802.11g: +15dBm@ 54Mbps
802.11n: +13dBm@ MCS7
Please do not use the DC power exceeding 5V 1A to power the device
Android iOS
9. ALARM FUNCTION
The SAT-1065 is equipped to support alarms on a 24 hour
(military time) based clock. Users can set scheduled
alarms and receive text alerts if the device does not
detect motion within the time period specified.
•To set an alarm, tap "Manage Alarm" and tap "add."
•The start time must be earlier than the end time for the
timer to set successfully.
10. PIR SETTINGS
The SAT-1065 allows users to be notified of motion,
tamper detection, and alarms. The smart sensor also
contains technology to monitor battery charge, and alert
when it detects the battery is low. These notifications can
be toggled on and off within the settings panel of the
SAT-1065.
11. Motion Detection History
The SAT-1065 keeps a running log of activity, showing
when the device has detected motion. This information
can be viewed by tapping "History" on the main sensor
panel.
Table of contents
Popular Accessories manuals by other brands
Fencing SmartBox
Fencing SmartBox SmartBox user manual
Century
Century SENSORE PIR SENS3-36044 quick start guide
Extron electronics
Extron electronics OCS 100C Setup guide
Petzl
Petzl VULCAN TRIACT-LOCK quick start guide
Flybar
Flybar ipogo jr. owner's manual
Grandview
Grandview LF-MixxFII Installation and operation manual
Servodan
Servodan 23-570 user manual
PCB Piezotronics
PCB Piezotronics IMI SENSORS 641B10 Installation and operating manual
Lightolier
Lightolier 1101HCB specification
brennenstuhl
brennenstuhl Premium-PROTECT-Line Directions for use
OJ Electronics
OJ Electronics ETOG-55 instructions
Interlogix
Interlogix RF711I4 Installation sheet
