Rehabmart ACC 314 Guide

ISSUED: 01-25-07 SHEET NO: 009-9035-1
1 of 3
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
Model:ACC314
Installation&Assembly-LaptopArm
LAPTOPARM
IMPORTANT! Read entire instruction sheet before you start assembly and installation.
Some parts may appear slightly different than illustrated.

ISSUED: 01-25-07 SHEET NO: 009-9035-1
2 of 3
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
PART # QTY. DESCRIPTION
A009-1227 1 laptop tray
B009-1020 1 laptop tray clamp
C590-1057 1 T-knob
D520-1017 1 1/4" - 20 x 1 3/4" carriage bolt
E590-1074 2 plastic grommet
F201-1156 1 screen mount bracket
G009-1230 1 shelf support
H520-2325 7 1/4 x 12 mm decorative screw
I530-1022 4 1/4 - 20 mm square nut
J540-9406 4 washer
K590-1209 5 button bumper
L560-9646 1 allen wrench
Parts List
Some parts may appear slightly different than illustrated.
Before you start make sure all parts
listed are included with your product.
F
G
K
JI
H
D
A
B
C
Slide screen mount bracket (F) onto upright so
that 1/4-20 nuts (I) slide into slots of upright as
shown in figure 2 and detail 1. Slide screen
mount bracket to desired position, level, then
tighten 1/4-20 x 12 mm screws (H) using 4 mm
allenwrench(L).
F
SLOT
fig 2
H
I
H
12
NOTE:Ifyouareaddingnewshelftoanalreadyassembledproduct,reversestepsuptotheshelf
installationstep(removingscreenandadapterplatefromcart)followingthemaininstructionsheet.
L
E
H
J
I
UPRIGHT
Loosely attach four 1/4-20 x 12 mm screws (H),
washers (J), and 1/4-20 nuts (I) to screen mount
bracket(F).
F
detail 1

ISSUED: 01-25-07 SHEET NO: 009-9035-1
3 of 3
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
DETAIL 2
Attach self support (G) to screen bracket bracket (F) as shown in fig. 3.1. Insert three 1/4-20 x 12 mm
screws (H) into screen mount bracket (F), leaving 1/8" of exposed thread as shown in fig. 3.2 and detail 2.
3
4
G
F
fig 3.1
H
1/8"
fig 3.2
Attach laptop tray (A) to shelf support (G) using clamp (B),
carriage bolt (D) and T-knob (C). Hook tabs of clamp (A) into
slots of laptop tray (A) as shown in fig. 5.1, then secure
clamp and tray around shelf using carriage bolt (D) and
T-knob (C) as shown fig.5.2.
Attach two grommets (E) to back of laptop tray (A), and
attach five button bumper (K) to the top of laptop tray (A)
as shown below. 5
A
E
©2007PeerlessIndustries,Inc.Allrightsreserved.
PeerlessisaregisteredtrademarkofPeerlessIndustries,Inc.
AB
D
C
fig 5.1 fig 5.2
CLAMP CARRIAGE
BOLT
T-KNOB