Rejuvenation ELKTON User manual

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2018.03.20 www.rejuvenation.com 1/8
ELKTON DOUBLE SINK VANITY

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2018.03.20 www.rejuvenation.com 2/8
BEFOREYOUBEGIN
Marbletopisbothheavy,anduntilinstalled,fragile.Pleasehaveahelperandusecautionwhenmovingmarble
top.
Makesuretoobservealllocalplumbingcodes.
Priortoinstallation,unpackandinspectboththeconsoleandmarbletopandporcelainlavatoryfordamage.
Locatetheinstallationpartspackageandputinasafeplace—youwillneedthisforinstallation.
Donotdisposeofanypackagingorcontentsoftheshippingcartonuntilassemblyiscompletedtoavoidaccidentally
discardingsmallpartsorhardware.
Installationassumesthatwallsandfloorareplumbandlevel.Pleasemakeappropriateadjustmentsforother
conditions.
Removeanymoldingthatmaypreventtheconsolefrombeingsetflushtothefinishedwall.
TOOLSANDMATERIALS
Tapemeasure
Pencil
Level
Drillwithappropriatedrillanddriverbits
Eyeprotection
Clear100%siliconeadhesivecaulk
Woodscrews(forsecuringconsoletowoodframing)
CAREINSTRUCTIONS
Dustoftenusingaclean,soft,dryandlint‐freecloth.
Immediatelyblotupspills,thenwipewithaclean,dampcloth.
Wedonotrecommendtheuseofchemicalcleansers,abrasivesorfurniturepolishonourlacqueredfinish.
Hardwaremayloosenovertime.Periodicallychecktomakesureallconnectionsaretight.Re‐tightenifnecessary.

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2018.03.20 www.rejuvenation.com 3/8
A
B
4x
D
C
∅8 x 2 3/4" – 4x

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2018.03.20 www.rejuvenation.com 4/8
TEST FIT THE VANITY BASE
•Remove the drawer:
1. Pull openthe drawer.
2. Remove the 4 screws on the underside of the drawer that attach drawer slide to the
drawer .
3. Lift up the front ofthe drawer aninch and pull forward to disengage the tabs at the
back of the drawer.
4. Set aside ina safe place and push the drawer slides back into the vanity.
4x

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2018.03.20 www.rejuvenation.com 5/8
TEST FIT THE VANITY BASE (cont’d)
Position the vanity base in the desired location against the finished wall.
Verify that the vanity base is level: front to back and side to side. Adjust the levelers at the
bottom of the legs as necessary.
5x

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2018.03.20 www.rejuvenation.com 6/8
INSTALL THE VANITY BASE AND MARBLE TOP
•Locate two wall studs to secure thevanity base. Mark these locations on the back rail
of the vanity base. Drill pilot holesthrough the back rail and into the studs. If necessary
provide shims between vanity and back rail so the back rail is not distorted.
•Using wood screws, secure the vanity to the wall.
•Apply a bead of clear 100% silicone adhesive caulk around perimeter ofconsole top.
•With the help of an assistant, carefully lift the marble top into position. Check carefully
for fit and alignment.
A
B

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2018.03.20 www.rejuvenation.com 7/8
INSTALL THE SINK AND FAUCET
•Temporarily position the sinksover the cutout and make sure thatit is aligned properly.
•Apply several pieces of bluepainters tape on both the countertop and sink. Make marks
on tape as an alignment guide for final installation.
•Referring to the faucet manufacturer’s instructions, install the drain and faucet
assemblies onto the sink.
•Turn the sinkson one side and apply a small bead ofclear 100% silicone adhesive caulk
around the bottom edge of the sink.
•Holding the sinksslightly abovethe desired location, aligning it with the guide marks.
Gently lower the sink into place. Carefully check placement and alignment.
•Press down on sinksto ensure atight seal. Let the sealant set, as stated in the silicone
adhesive caulking label’s instructions.
•Connect the supply lines and drain pipes.
A

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2018.03.20 www.rejuvenation.com 8/8
REINSTALL THE DRAWER
1. Extend the drawer slides and note the alignment hook on the back of each slide.
2. Note the notchedholes at the back of the drawer.
3. Set the drawer onto the slides so that the drawer slide hook fit into the notches.
4. Reinstall the 4screws on the underside of the drawer that attach drawer slide to
the drawer sides.
4x