REMEHA Quinta Ace 135 User manual

United Kingdom
en
Service Manual
High-efficiency wall-hung gas boiler
Quinta Ace
135
160
HMI T-control

Dear Customer,
Thank you very much for buying this appliance.
Please read through the manual carefully before using the product, and keep it in a safe place for later reference. In order to
ensure continued safe and efficient operation we recommend that the product is serviced regularly. Our service and customer
service organisation can assist with this.
We hope you enjoy years of problem-free operation with the product.

Contents
1 About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Additional documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Symbols used in the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2 Description of the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2.2 Operating principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.1 Gas/air regulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.2 Combustion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.3 Control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.2.4 Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.5 Regulating the water temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2.6 Protection against shortage of water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.7 Water flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.8 Hydraulic pressure sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.9 Air pressure differential switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.2.10 Circulating pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.11 Calorifier connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.12 Cascade system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Main components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Introduction to the e-Smart controls platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3 Use of the control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 Control panel components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Description of the home screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 Description of the main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.4 Description of the icons in the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
4 Installer instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.1 Accessing the user level menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2 Accessing the installer level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.3 Commissioning the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.3.1 Chimney sweep menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3.2 Saving the commissioning settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.4 Configuring the installation at installer level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.4.1 Changing the control panel settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.4.2 Setting the installer details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4.4.3 Setting the parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.4.4 Setting the heating curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
4.4.5 Increasing the domestic hot water temperature temporarily . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.5 Maintaining the installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.5.1 Viewing the service notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.5.2 Reading out measured values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
4.5.3 Viewing production and software information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.5.4 Manual deaeration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
4.6 Resetting or restoring settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.6.1 Resetting the configuration numbers CN1 and CN2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.6.2 Carrying out an auto detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.6.3 Restoring the commissioning settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.6.4 Resetting to factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5 Installation examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
5.1 The SCB-01 expansion PCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.1 Introduction to parameter codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.2 Searching the parameters, counters and signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
6.3 List of parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.3.1 CU-GH06c control unit parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6.3.2 SCB-01 expansion PCB parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
6.4 List of measured values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.4.1 CU-GH06c control unit counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6.4.2 SCB-01 expansion PCB counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.4.3 CU-GH06c control unit signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Contents
7701860 - v.10 - 10122021 3

6.4.4 SCB-01 expansion PCB signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
6.4.5 Status and sub-status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.1 Maintenance regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
7.2 Maintenance message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7.3 Standard inspection and maintenance operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7.3.1 Checking the water pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
7.3.2 Checking the water quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
7.3.3 Checking the ionisation current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
7.3.4 Checking the flue gas discharge/air supply connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.3.5 Checking the combustion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
7.3.6 Checking the air pressure differential switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
7.3.7 Checking the automatic air vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
7.3.8 Checking the burner and cleaning the heat exchanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7.3.9 Cleaning the condensate collector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
7.3.10 Cleaning the siphon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
7.4 Specific maintenance work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
7.4.1 Replacing the ionisation/ignition electrode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
7.4.2 Checking the non-return valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
7.5 Finalising work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
8.1 Error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.1.1 Display of error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
8.1.2 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
8.1.3 Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
8.1.4 Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
8.2 Error history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
8.2.1 Reading out and clearing the error history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
9 Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
9.1 Electrical diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
10 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
10.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
10.2 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Contents
4 7701860 - v.10 - 10122021

1 About this manual
1.1 Additional documentation
The following documentation is available in addition to this manual:
Installation and user manual
Water quality instructions
1.2 Symbols used in the manual
This manual contains special instructions, marked with specific symbols. Please pay extra attention when these symbols are
used.
Danger
Risk of dangerous situations that may result in serious personal injury.
Danger of electric shock
Risk of electric shock that may result in serious personal injury.
Warning
Risk of dangerous situations that may result in minor personal injury.
Caution
Risk of material damage.
Important
Please note: important information.
The symbols mentioned below are of lower importance, but they can help you navigate or give useful information.
See
Reference to other manuals or pages in this manual.
Helpful information or extra guidance.
Direct menu navigation, confirmations will not be shown. Use if you are familiar with the system.
2 Description of the product
2.1 General description
The Quinta Ace boiler is a high-efficiency wall-hung gas boiler with the
following properties:
High-efficiency heating.
Limited emissions of polluting substances.
Ideal choice for cascade configurations.
The following boiler types are available:
Tab.1 Boiler types
Name Output(1)
Quinta Ace 135 136 kW
Quinta Ace 160 161 kW
(1) Nominal output Pn 50/30 °C
1 About this manual
7701860 - v.10 - 10122021 5

2.2 Operating principle
2.2.1 Gas/air regulation
The boiler is equipped with a casing that also serves as an air box. The
fan draws in the combustion air. The gas is injected into the venturi and
mixed with the combustion air. The fan speed is controlled on the basis of
the settings, the heat demand and the prevailing temperatures measured
by the temperature sensors. The gas/air ratio control ensures an accurate
mixture of the required amounts of gas and air. This provides optimum
combustion over the entire heat input range. The gas/air mixture goes to
the burner, where it is ignited by the ignition electrode.
Important
The combustion air supply is checked before each burner start,
and at least once every 24 hours. During continuous operation
(e.g. supplying process water), please note that the boiler control
will reset every 24 hours.
2.2.2 Combustion
The burner heats the central heating water flowing through the heat
exchanger. If the temperature of the flue gases is lower than the dew point
(approx. 55°C), the water vapour condenses in the heat exchanger. The
heat released during this condensation process (referred to as the latent
or condensation heat) is also transferred to the central heating water. The
cooled flue gases are discharged through the flue gas discharge pipe. The
condensed water is discharged through a siphon.
2.2.3 Control system
The e-Smart electronic control system ensures that your heating system is
smart and reliable. This means that the boiler responds practically to
negative environmental influences (such as limited water flow and air flow
problems). In the event of such influences, the boiler will not go into
lockout mode, but in the first instance will modulate back. Depending on
the nature of the circumstances, a warning, blocking or lock-out may
occur. The boiler continues to supply heat provided the situation is not
dangerous. With this control system, your boiler is also equipped for
remote control and monitoring.
2.2.4 Control
On/off control
The heat input varies between the minimum and the maximum values
on the basis of the flow temperature set on the boiler. It is possible to
connect a 2-wire on/off thermostat or a power stealing thermostat to the
boiler.
Modulating control
The heat input varies between the minimum and the maximum values
on the basis of the flow temperature determined by the modulating
controller. The boiler output can be modulated with an appropriate
modulating controller.
Analogue control (0 - 10 V)
The heat input varies between the minimum and the maximum values
on the basis of the voltage present at the analogue input.
2.2.5 Regulating the water temperature
The boiler is fitted with an electronic temperature control with a flow and
return temperature sensor. The flow temperature can be adjusted between
20°C and 90°C. The boiler modulates back when the set flow temperature
is reached. The switch-off temperature is the set flow temperature + 5°C.
2 Description of the product
6 7701860 - v.10 - 10122021

2.2.6 Protection against shortage of water
The boiler is fitted with low water level protection based on temperature
measurements. By modulating back when the water flow threatens to
become insufficient, the boiler remains operational as long as possible.
The boiler issues a warning in the event of no or too little water. With an
insufficient flow ΔT ≥ 25 K or too great an increase in the heat exchanger
temperature sensor, the boiler goes into blocking mode.
2.2.7 Water flow
The modulating control of the boiler limits the maximum difference
between the flow temperature and return temperature. In addition, a heat
exchanger temperature sensor is mounted to monitor the minimum water
flow. This limits the maximum increase in the heat exchanger temperature
and monitors the maximum temperature difference between the flow,
return and heat exchanger temperatures. As a result, the boiler is not
affected by low water flow.
2.2.8 Hydraulic pressure sensor
The hydraulic pressure sensor records the water pressure in the boiler.
Change the threshold value for the hydraulic pressure sensor using
parameter AP006.
2.2.9 Air pressure differential switch
The air pressure differential switch is a protection against a blocked trap or
blocked air supply/flue gas outlet.
Before start-up and when the boiler is in operation, the air pressure
differential switch APS measures the difference in pressure between the
measuring points on the condensate collector p+ and the air box p-. If the
pressure difference is greater than 6 mbar, then the boiler will lock out.
After eliminating the cause of the breakdown, the boiler can be unlocked.
2.2.10 Circulating pump
ΔP Boiler resistance (mbar)
QFlow rate (m3/h)
The boiler is supplied without a pump. Take the boiler resistance and
system resistance into account when selecting a pump.
Caution
Maximum power consumption may be 300 VA. Use an auxiliary
relay for a pump with greater power.
2.2.11 Calorifier connection
A calorifier can be connected to the boiler. Our range includes various
calorifiers.
Important
Contact us for more information.
2.2.12 Cascade system
The boiler is ideally suited for a cascade system. There are a number of
standard solutions available.
Fig.1 Water resistance
AD-0000857-02
170
300
250
200
150
100
50
0
0 1 2 3 4 5 6 7 8 9 10
6,5
[m3/h]
Q
T = 20 K
2 Description of the product
7701860 - v.10 - 10122021 7

Important
Contact us for more information.
2.3 Main components
1Air inlet connection
2Casing/air box
3Type plate
4LED interior light
5Flow temperature sensor
6Adapter
7Heat exchanger
8Temperature sensor for heat exchanger
9Ignition transformer
10 Heat exchanger inspection cover
11 Water pressure sensor
12 Return temperature sensor
13 Service connector (PC connection)
14 Control panel
15 On/off switch
16 Condensate collector
17 Air inlet silencer
18 Gas pressure measuring point
19 Main PCB (CU-GH)
20 Gas control valve
21 Venturi
22 Fan
23 Non-return valve
24 Air pressure differential switch
25 Automatic air vent
26 Flue gas measuring point
27 Flue gas connection
2.4 Introduction to the e-Smart controls platform
The Quinta Ace boiler is equipped with the e-Smart controls platform. This
is a modular system, and offers compatibility and connectivity between all
products that make use of the same platform.
Fig.3 Generic example
AD-3001366-02
CB
CU B
A
C
L-Bus
SCB
GTW
GTW
MK
R-Bus
S-Bus
RU
Tab.2 Components in the example
Item Description Function
CU Control Unit: Control unit The control unit handles all basic functionality of the appli
ance.
CB Connection Board: Connection PCB The connection PCB provides easy access to all connectors
of the control unit.
SCB Smart Control Board: Expansion PCB An expansion PCB provides extra functionality, like an internal
calorifier or multiple zones.
Fig.2 Main components
AD-0000218-03
10
9
6
7
8
2
1
5
4
11
13
14
15
12 17
18
19
20
21
22
16
26
25
23
24
27
3
2 Description of the product
8 7701860 - v.10 - 10122021

Item Description Function
GTW Gateway: Conversion PCB A gateway can be fitted to an appliance or system, to provide
one of the following:
Extra (wireless) connectivity
Service connections
Communication with other platforms
MK Control panel: Control panel and display The control panel is the user interface to the appliance.
RU Room Unit: Room unit (for example, a thermo
stat)
A room unit measures the temperature in a reference room.
L-Bus Local Bus: Connection between devices The local bus provides communication between devices.
S-Bus System Bus: Connection between appliances The system bus provides communication between appliances.
R-Bus Room unit Bus: Connection to a room unit The room unit bus provides communication to a room unit.
A Device A device is a PCB, control panel or a room unit.
B Appliance An appliance is a set of devices connected via the same L-
Bus
C System A system is a set of appliances connected via the same S-Bus
Tab.3 Specific devices delivered with the Quinta Ace boiler
Name visible
in display
Software ver
sion
Description Function
FSB-WHB-
HE-150-300
2.1 Control unit CU-GH06c The CU-GH06c control unit handles all basic functionality of
the Quinta Ace boiler.
MK3 1.85 Control panel HMI T-control The HMI T-control is the user interface to the Quinta Ace boil
er.
SCB-01 1.3 Expansion PCB SCB-01 The SCB-01 provides a 0-10 V connection for a PWM system
pump and two potential-free contacts for status notification.
3 Use of the control panel
3.1 Control panel components
1 Rotary knob to select a tile, menu or setting
2 Confirm button to confirm the selection
3 Back button :
Short button press: Return to the previous level or previous
menu
Long button press: Return to home screen
4 Menu button to go to the main menu
5 Display
6 Status LED
3.2 Description of the home screen
This screen is shown automatically after start-up of the appliance. The
control panel automatically enters standby mode (black screen) if the
buttons are not used for 5 minutes. Press one of the buttons on the control
panel to activate the screen again.
You can navigate from any menu to the home screen by pressing the back
button for several seconds.
The tiles on the home screen provide quick access to the corresponding
menus. Use the rotary knob to navigate to the desired item and press the
button to confirm the selection.
Fig.4 Control panel components
AD-3000932-02
4
6
3
2
1
5
3 Use of the control panel
7701860 - v.10 - 10122021 9

1Tiles: the selected tile is highlighted
2Date and time | Name of the screen (actual position in the menu)
3Information about the selected tile
4Icons indicating navigation level, operating mode, errors and other
information.
3.3 Description of the main menu
You can navigate from any menu directly to the main menu by pressing
the menu button . The number of accessible menus depends on the
access level (user or installer).
ADate and time | Name of the screen (actual position in the menu)
BAvailable menus
CBrief explanation of the selected menu
Tab.4 Available menus for the user
Description Icon
Enable installer access
System Settings
Version Information
Tab.5 Available menus for the installer
Description Icon
Disable installer access
Installation Setup
Commissioning Menu
Advanced Service Menu
Error History
System Settings
Version Information
3.4 Description of the icons in the display
Tab.6 Icons
Icon Description
User menu: user-level parameters can be configured.
Installer menu: installer-level parameter can be configured.
Information menu: read out various current values.
System settings: system parameters can be configured.
Error indicator.
Gas boiler indicator.
Domestic hot water tank is connected.
The outdoor temperature sensor is connected.
Boiler number in cascade system.
The solar calorifier is on and its heat level is displayed.
Burner output level (1 to 5 bars, with each bar representing 20% output).
Fig.5 Icons on home screen
AD-3001157-03
All OK
Error Status
i
i
All OK
Home Screen
22/02/2018 11:20
2 43
1
Fig.6 Items in the main menu
AD-3000935-02
........ ....... .......... ... ...... .........
....... ........
........ .......
...... .....11:20
.......... ......... ............
.... ..........
.................. ......
B
C
A
3 Use of the control panel
10 7701860 - v.10 - 10122021

Icon Description
The pump is running.
Three-way valve indicator.
Display of the system water pressure.
Chimney sweep mode is enabled (forced full load or low load for O2 measurement).
Energy-saving mode is enabled.
DHW boost is enabled.
Timer program is enabled: The room temperature is controlled by a timer program.
Manual mode is enabled: The room temperature is set to a fixed setting.
Temporary overwrite of the timer program is enabled: The room temperature is changed temporarily.
The holiday program (including frost protection) is active: The room temperature is reduced during your holiday to
save energy.
Frost protection is enabled: Protect the boiler and installation from freezing in winter.
Service notification: service needed.
Installer contact details are displayed or can be filled in.
Tab.7 Icons - On/off
Icon Description Icon Description
CH operation is enabled. CH operation is disabled.
DHW operation is enabled. DHW operation is disabled.
The burner is on. The burner is off.
Bluetooth enabled and connected (icon is non-trans
parent).
Bluetooth enabled and disconnected (icon is trans
parent).
Heating enabled.
Cooling enabled.
Heating/cooling enabled. Heating/cooling disabled.
Tab.8 Icons - Zones
Icon Description
All zones (groups) icon.
Living room icon.
Kitchen icon.
Bedroom icon.
Study icon.
Cellar icon.
4 Installer instructions
4.1 Accessing the user level menus
The tiles on the home screen provide quick access for the user to the
corresponding menus.
4 Installer instructions
7701860 - v.10 - 10122021 11

1. Use the rotary knob to select the required menu.
2. Press the button to confirm the selection.
The available settings of this selected menu appear in the display.
3. Use the rotary knob to select the desired setting.
4. Press the button to confirm the selection.
All options for change will appear in the display (if a setting cannot
be changed, Cannot edit read-only datapoint will appear in the
display).
5. Use the rotary knob to change the setting.
6. Press the button to confirm the selection.
7. Use the rotary knob to select the next setting or press the button to
return to the home screen.
4.2 Accessing the installer level
Some settings are protected by installer access. Enable installer access in
order to change these settings.
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Access the installer level via the tile:
1.1. Select the tile [ ].
1.2. Use code: 0012.
The tile [ ] shows that the installer access is On, and the
icon in the top right of the display changes into .
2. Access the installer level via the menu:
2.1. Select Enable installer access from the Main Menu.
2.2. Use code: 0012.
When the installer level is enabled or disabled, the status of
the tile [ ] changes into On or Off.
When the control panel is not used for 30 minutes, the installer access is
disabled automatically. You can manually disable installer access by:
Selecting the tile [ ].
Selecting Disable installer access from the Main Menu.
4.3 Commissioning the appliance
At first start-up of the appliance, the display will show the commissioning
wizard. Depending on the appliance, some steps take a few minutes to
complete, for example appliances that need to deaerate after installation
or need to configure a boiler.
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Start up the appliance.
Fig.7 Menu selection
AD-3001387-01
Not set
Home Screen
22/02/2018 11:20
... ...
........ .......
........ .......
......
Fig.8 Confirm menu selection
AD-3001388-01
... ...
........ .......
........ .......
......
Not set
Home Screen
22/02/2018 11:20
Fig.9 Installer level
AD-3001378-02
00:12
0 1 2
3
4
0
1
5
6
2
0
3
4
5
1
2
3
4
1
2
3
4
0
........ .......
........ .......
........ ......... ...
..... ... ....... .... .. ..... ....... .... ..... .......
i
Fig.10 Installer level
AD-3001378-02
00:12
0 1 2
3
4
0
1
5
6
2
0
3
4
5
1
2
3
4
1
2
3
4
0
........ .......
........ .......
........ ......... ...
..... ... ....... .... .. ..... ....... .... ..... .......
i
4 Installer instructions
12 7701860 - v.10 - 10122021

2. Follow the instructions on the display.
Important
The appliance might take a few minutes during certain steps while
commissioning. Do not shut off the appliance or try to bypass
steps, unless stated otherwise on the display.
3. You can access individual commissioning steps:
3.1. Press the button.
3.2. Select Commissioning Menu.
3.3. Select the commissioning step you wish to perform.
4.3.1 Chimney sweep menu
Select the tile [ ] to open the chimney sweep menu. The Change load
test mode menu will appear:
A Change load test mode
B Load test mode
Tab.9 Load tests in the chimney sweep menu
Change load test mode Settings
Off No test
Low power Part load test
Medium power Full load test for Central Heating mode
High power Full load test for Central Heating + Domestic Hot Water mode
Tab.10 Load test settings
Load Test menu Settings
Func. test status Select the load test to start the test.
System Flow Temp Read the central heating flow temperature
T return Read the central heating return temperature
Actual fan RPM Read the actual fan speed
Actual flame current Read the actual flame current
Fan RPM Max CH Adjust the maximum fan speed during Central Heating mode
Fan RPM Min Adjust the minimum fan speed during Central Heating + Domestic Hot Water mode
Fan RPM Start Adjust the start fan speed
Performing the full load test
1. Select the tile [ ].
The Change load test mode menu appears.
Fig.11 Load test
AD-3000941-03
..... ... ....... .... .. ..... .... .........
..... ... ....... ....
..... ... ....... ....
....... .... .. ..... .... .......
....... ...........
......
.....
...
.....
..... ... ....... .... .. ..... ....... .... ..... .......
i
.....
....... .... ....... .... .......
.... ...... ....... ......11:20
A
B
4 Installer instructions
7701860 - v.10 - 10122021 13

2. Select the test Medium power.
AChange load test mode
BMedium power
The full load test starts. The selected load test mode is shown in the
menu and the icon appears in the top right of the screen.
3. Check the load test settings and adjust if necessary.
Only the parameters shown in bold can be changed.
Performing the low load test
1. If the full load test is still running, press the button to change the
load test mode.
2. If the full load test was finished, select the tile [ ] to restart the
chimney sweep menu.
AChange load test mode
B Low power
3. Select the Low power test in the menu Change load test mode.
The low load test starts. The selected load test mode is shown in
the menu and the icon appears in the top right of the screen.
4. Check the load test settings and adjust if necessary.
Only the parameters shown in bold can be changed.
5. End the low load test by pressing the button.
The message Running load test(s) stopped! is displayed.
4.3.2 Saving the commissioning settings
You can save all current settings on the control panel. These settings can
be restored if necessary, for example after replacement of the control unit.
> Advanced Service Menu > Save as commissioning settings
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Press the button.
2. Select Advanced Service Menu.
3. Select Save as commissioning settings.
4. Select Confirm to save the settings.
When you have saved the commissioning settings, the option Revert
commissioning settings becomes available in the Advanced Service Menu.
4.4 Configuring the installation at installer level
Configure the installation by pressing the button and selecting
Installation Setup . Select the control unit or circuit board you want to
configure:
Tab.11
Icon Zone or function Description
CIRCA / CH Central heating circuit
Commercial boiler Gas boiler
Gas fired appliance Gas boiler
Fig.12 Full load test
AD-3000941-03
..... ... ....... .... .. ..... .... .........
..... ... ....... ....
..... ... ....... ....
....... .... .. ..... .... .......
....... ...........
......
.....
...
.....
..... ... ....... .... .. ..... ....... .... ..... .......
i
.....
....... .... ....... .... .......
.... ...... ....... ......11:20
A
B
Fig.13 Low load test
AD-3000941-03
..... ... ....... .... .. ..... .... .........
..... ... ....... ....
..... ... ....... ....
....... .... .. ..... .... .......
....... ...........
......
.....
...
.....
..... ... ....... .... .. ..... ....... .... ..... .......
i
.....
....... .... ....... .... .......
.... ...... ....... ......11:20
A
B
4 Installer instructions
14 7701860 - v.10 - 10122021

Tab.12 Configuring a zone or function of CU-GH08
Parameters, counters, signals Description
Parameters Set the parameters at installer level
Counters Read the counters at installer level
Signals Read the signals at installer level
4.4.1 Changing the control panel settings
You can change the control panel settings within system settings.
> System Settings
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Press the button.
2. Select System Settings .
3. Perform one of the operations described in the table below:
Tab.13 Control panel settings
System Settings menu Settings
Set Date and Time Set the current date and time
Select Country and Language Select your country and language
Daylight Saving Time Enable or disable daylight saving time. When enabled daylight saving time will
update the systems internal time to correspond with summer and winter time.
Installer Details Read out the name and phone number of the installer
Set Heating Activity Names Create the names for the activities of the timer program
Set Screen Brightness Adjust the brightness of the screen
Set click sound Enable or disable the click sound of the rotary knob
License Information Read out detailed license information from the device platform application
4.4.2 Setting the installer details
You can store your name and phone number in the control panel to be
read by the user. When an error occurs these contact details will be
displayed.
> System Settings > Installer Details
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Press the button.
Enable installer access if it is not enabled.
1.1. Select Enable installer access.
1.2. Use code 0012.
2. Select System Settings .
3. Select Installer Details.
4. Enter the following data:
Installer name Your company's name
Installer phone Your company's phone number
4.4.3 Setting the parameters
You can change the settings of the control unit and the connected
expansion boards, sensors etc. to configure the installation. The factory
settings support the most common heating systems. The user or the
installer can optimise the parameters as required.
4 Installer instructions
7701860 - v.10 - 10122021 15

Important
Changing the factory settings may adversely affect the operation
of the installation.
> Installation Setup > select zone or device > Parameters,
counters, signals > Parameters
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Press the button.
2. Select Installation Setup.
3. Select the zone or device you want to configure.
4. Select Parameters, counters, signals.
5. Select Parameters.
A Parameters
Counters
Signals
B List of settings or values
The list of available parameters is displayed.
4.4.4 Setting the heating curve
When an outdoor temperature sensor is connected to the installation, the
relation between the outdoor temperature and the central heating flow
temperature is controlled by a heating curve. This curve can be adjusted
to the requirements of the installation.
Select zone > Heating Curve
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Select the tile of the zone you want to configure.
2. Select Control strategy.
3. Select the setting Outdoor Temp. based or Outdoor & room based.
The option Heating Curve appears in the Zone setup menu.
4. Select Heating Curve.
A graphic display of the heating curve is shown.
5. Adjust the following parameters:
Tab.14 Settings
A Slope: Slope of the heating curve:
Underfloor heating circuit: slope between 0.4
and 0.7
Radiator circuit: slope at approximately 1.5
B Max: Maximum temperature of the heating circuit
C Base: Ambient temperature setpoint
D xx°C ; xx
°C
Relationship between the heating circuit flow
temperature and the outdoor temperature. This
information is visible throughout the slope.
4.4.5 Increasing the domestic hot water temperature temporarily
You can temporary increase the hot water temperature when the time
program is active with the reduced temperature setpoint. Use this to
deviate from the time program or testing of the hot water production.
Fig.14 Parameters, counters, signals
AD-3000936-02
: .... ...... ........ ..............
11:20
..... ... ....... .... .. ..... .... .........
..... ... ....... ....
..... ... ....... ....
....... .... .. ..... .... .......
....... ...........
......
.....
...
........ ....... .....
............................ ..............
A
B
Fig.15 The heating curve
AD-3001402-01
.... ...... ........ ..............
11:20
.... ...
... ....
...... ...
... ...
........ ...................
........ ...................
.... .....
D
B
A
C
4 Installer instructions
16 7701860 - v.10 - 10122021

> Installation Setup > Internal DHW > Hot water boost >
Duration of temporary overwrite
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Press the button.
2. Select Installation Setup.
3. Select Internal DHW.
4. Select Hot water boost.
5. Select Duration of temporary overwrite.
6. Set the duration in hours and minutes.
The hot water temperature is increased to the DHW comfort
setpoint.
You can abort the temporary increase by selecting Reset.
4.5 Maintaining the installation
4.5.1 Viewing the service notification
When a service notification appears on the display, you can view the
details of the notification.
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Select the tile [ ].
The View Service Notification menu opens.
2. Select the parameter or value you want to view.
4.5.2 Reading out measured values
The appliance continually registers various measured values from the
system. You can read these values on the control panel.
> Installation Setup > select zone or device > Parameters,
counters, signals > Counters or Signals
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Press the button.
2. Select Installation Setup.
Enable installer access if Installation Setup is not available.
2.1. Select Enable installer access.
2.2. Use code 0012.
3. Select the zone or device you want to read out.
4. Select Parameters, counters, signals.
5. Select Counters or Signals to read out a counter or signal.
A Parameters
Counters
Signals
B List of settings or values
4.5.3 Viewing production and software information
You can read details about the production dates, hardware and software
versions of the appliance and all connected devices.
Fig.16 Parameters, counters, signals
AD-3000936-02
: .... ...... ........ ..............
11:20
..... ... ....... .... .. ..... .... .........
..... ... ....... ....
..... ... ....... ....
....... .... .. ..... .... .......
....... ...........
......
.....
...
........ ....... .....
............................ ..............
A
B
4 Installer instructions
7701860 - v.10 - 10122021 17

> Version Information
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Press the button.
2. Select Version Information.
3. Select the appliance, control board or any other device you want to
view.
ASelect the appliance, control board or device
BList of information
4. Select the information you want to view.
4.5.4 Manual deaeration
You can manually deaerate your appliance.
> Commissioning Menu > Deaeration program
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Press the button.
2. Select Commissioning Menu.
3. Select Deaeration program.
The manual de-aeration menu opens.
4. Follow the instructions on the display.
You can press and hold to abort the procedure.
4.6 Resetting or restoring settings
4.6.1 Resetting the configuration numbers CN1 and CN2
The configuration numbers must be reset when indicated by an error
message or when the control unit has been replaced. The configuration
numbers can be found on the data plate of the appliance.
Important
All custom settings will be erased when the configuration numbers
are reset. Depending on the appliance, there can be factory set
parameters to enable certain accessories.
Use the saved commissioning settings to restore these settings
after the reset.
If no commissioning settings were saved, write down custom
settings before resetting. Include all relevant accessory related
parameters.
> Advanced Service Menu > Set Configuration Numbers
Use the rotary knob to navigate.
Use the button to confirm your selection.
Fig.17 Version information
AD-3000936-02
: .... ...... ........ ..............
11:20
..... ... ....... .... .. ..... .... .........
..... ... ....... ....
..... ... ....... ....
....... .... .. ..... .... .......
....... ...........
......
.....
...
........ ....... .....
............................ ..............
A
B
4 Installer instructions
18 7701860 - v.10 - 10122021

A Select the control unit
B Extra information
C Configuration numbers
1. Press the button.
2. Select Advanced Service Menu.
3. Select Set Configuration Numbers.
4. Select the device you want to reset.
5. Select and change the CN1 setting.
6. Select and change the CN2 setting.
7. Select Confirm to confirm the changed numbers.
4.6.2 Carrying out an auto detect
The auto detect-function scans the installation for devices and other
appliances connected to the L-Bus and S-Bus. You can use this function
when a connected device or appliance has been replaced or removed
from the installation.
> Advanced Service Menu > Auto Detect
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Press the button.
2. Select Advanced Service Menu.
3. Select Auto Detect.
4. Select Confirm to carry out the auto-detect.
4.6.3 Restoring the commissioning settings
This option is only available when the commissioning settings were saved
on the control panel and allows you to restore these settings.
> Advanced Service Menu > Revert commissioning settings
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Press the button.
2. Select Advanced Service Menu.
3. Select Revert commissioning settings.
4. Select Confirm to restore the commissioning settings.
4.6.4 Resetting to factory settings
You can reset the appliance to the default factory settings.
> Advanced Service Menu > Reset to Factory Settings
Use the rotary knob to navigate.
Use the button to confirm your selection.
1. Press the button.
2. Select Advanced Service Menu.
3. Select Reset to Factory Settings.
4. Select Confirm to restore the factory settings.
Fig.18 Configuration numbers
AD-3001385-01
.... ...... ........ ..............
11:20
........
... .
... .
............ ....... ....... ....
......... ... .............. ...... .. .....
.......
.......
A
B
C
4 Installer instructions
7701860 - v.10 - 10122021 19

5 Installation examples
5.1 The SCB-01 expansion PCB
The SCB-01 has the following features:
Two potential free contacts for status notifications
0–10 V output connection for a PWM system pump
Expansion PCBs are automatically recognised by the control unit of the
boiler. If expansion PCBs are removed, the boiler will show an error code.
To resolve this error, an auto-detect must be carried out after removal.
6 Settings
6.1 Introduction to parameter codes
The controls platform makes use of an advanced system to categorise
parameters, measurements and counters. Knowing the logic behind these
codes, makes it easier to identify them. The code consists of two letters
and three numbers.
The first letter is the category the code relates to.
AAppliance: Appliance
CCircuit: Zone
DDomestic hot water: Domestic hot water
EExternal: External options
GGas fired: Gas-fired heat engine
PProducer: Central heating
Category D codes are appliance controlled only. When the domestic hot
water is controlled by an SCB, it is handled like a circuit, with C-category
codes.
The second letter is the type.
PParameter: Parameters
CCounter: Counters
MMeasurement: Signals
The number is always three digits. In certain cases, the last of the three
digits relates to a zone.
6.2 Searching the parameters, counters and signals
You can search and change data points (Parameters, counters, signals) of
the appliance, connected control boards and sensors.
> Installation Setup > Search datapoints
Fig.19 SCB-01 PCB
AD-3001514-01
NoCNc
Status
NoCNc
Status
+0
0-10
Fig.20 Code on a HMI T-control
AD-3001373-02
00:12 ...... ......
........ .......
........ .......
....................
..... ... ....... .... .. ..... ....... .... ..... .......
..... ... ....... .... .. ..... .... .........
..... ... ....... ....
..... ... ....... ....
....... .... .. ..... .... .......
....... ...........
......
.....
...
CP010
CP010
Fig.21 First letter
AD-3001375-01
CP010
Fig.22 Second letter
AD-3001376-01
CP010
Fig.23 Number
AD-3001377-01
CP010
5 Installation examples
20 7701860 - v.10 - 10122021