Remington BARBER'S BEST PRO User manual

5 YEAR WARRANTY
To register your product go to
remington-products.com.au
remington.co.nz
XR1475AU
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
BARBER’S BEST
PRO POWER SHAVER

2
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should
always be observed, including the following.
READ ALL INSTRUCTIONS BEFORE USING
For additional protection, the installation of a residual
current device (rcd) having a rated residual operating
current not exceeding 30 mA is advisable in the electrical
circuit supplying the bathroom. Ask your installer for advice.
WARNING - TO REDUCE THE RISK OF BURNS,
ELECTROCUTION AND FIRE OR INJURY TO PERSONS
DANGER - As with most electrical appliances, electrical
parts are electrically live even when the switch is off.
• The appliance should never be left unattended when plugged
into a power outlet, except when charging the appliance.
• This appliance should not be used by children or other
persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge unless they have
been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning
and use maintenance shall not be made by children without
supervision.
• Never operate this appliance if it has a damaged cord or
plug, if it is not working correctly, if it has been dropped or
damaged, or dropped into water. If the supply cord or plug
of the appliance is damaged it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard. It cannot be repaired. Keep the
cord away from heated surfaces.
• Charge, use and store the product at a temperature between
0°C and 32°C.

3
• Do not use outdoors or where aerosol (spray) products are
being used, or where oxygen is being administered.
• Do not use this appliance with damaged or broken tracks or
cutters, as injury may occur.
• Do not plug or unplug the appliance with wet hands.
• For household use only.
• Do not place or store the appliance or charging adaptor
where it can fall or be knocked into a sink or bath.
• Do not place in or drop into water or any other liquid.
• If an appliance falls into water, “unplug it” immediately. Do
not reach into the water.
• Unplug the charging adaptor from the electrical outlet
immediately after fully charging.
• Unplug and switch off this appliance before cleaning it.
• Use this appliance only for its intended use as described in
this manual.
• Do not use attachments not recommended by Remington.
• Never drop or insert any object into any opening of this
appliance.
• Always store the charging adaptor in a moisture-free
location.
• Do not use on people who are asleep.
• Do not use an extension cord or a voltage converter with this
appliance.
• Do not wrap the cord around the appliance.
Remington strongly recommends that an approved Safety Switch
(Residual current device) be installed to protect all bathroom
power outlets. Ask an electrical contractor for advice.
SAVE THESE INSTRUCTIONS

4
XR1475AU BARBER’S BEST PRO POWER SHAVER
USE & CARE MANUAL
Thank you for purchasing your new Remington®Barber’s Best Pro Power Shaver.
Inside this manual you will find tips on using and caring for your shaver.
5
6
1
4
3
10
1. 360° Pivoting Neck
2. Full Floating Heads
3. Pop Up Trimmer (not shown)
4. On/Off & Turbo Push Button
5. LED Display
6. Charging Pins (not shown)
7. Beard Trimmer Attachment
8. Adjustable Stubble Comb
9. Daily Cleansing Charcoal
Infused Facial Brush
10. Charging Stand
Also Includes:
• Head Guard
• Premium Storage Pouch
• Cleaning Brush
• Power Adaptor
KEY PARTS
2
7
8
9

5
XR1475AU SPECIFICATIONS
Power System Cordless
Initial Charge Time 24 Hours
Full Charge Time 90 Minutes
Cordless Run Time 60 Minutes
Quick Charge Yes
Turbo Function Yes
Indicators LED Digital Battery Indicator
LED Turbo Function Indicator
Worldwide Voltage Yes
Charging Stand Yes
Travel Lock Yes
Shaver Head Replacement Part No. SPR-XR1475AU
Power System
The XR1475AU shaver can only be used without the power cord. The shaver will not run
while it is charging on its charging stand.
Quick Charge
The quick charge allows placing the shaver on charge for 5 minutes then it will deliver up to
5 minutes of use - approximately one or two shaves.
Turbo Function
Press the power button once to activate standard shave speed. This speed is intended for
daily shaving or finer beards. Press the power button twice to activate the turbo function,
this increases the motor RPM to provide a more powerful shave. The turbo function is
intended for shaving a two or three day beard growth and provide added power to heavier
areas of the beard.
LED Indicator
Displays the number of minutes of remaining battery power and displays when the turbo
function is on.
Worldwide Voltage
Shaver automatically adapts to an outlet voltage between 100V and 240V.
Note: Some countries will require the use of a plug adaptor that is not included
with your shaver.
Folding Charging Stand
Rotate open to hold the shaver while charging. The stand collapses down around shaver
for travel or storage.
Travel Lock
To engage the travel lock press and hold the on/off button for 3 seconds. The LED display

6
will flash 5 times to indicate the lock is set. While the travel lock is set, if the on/off button
is pressed the LED display will flash 3 times to indicate the shaver is on travel lock mode.
To turn the travel lock off, press and hold the on/off button for 3 seconds. The LED display
will flash 3 times while the button is being pressed and then the shaver will turn on.
CHARGING
1. Plug power cord adaptor into the charging stand (Diagram A).
2. Place the shaver into the charge stand (Diagram B).
3. Plug the adaptor into the wall outlet (Diagram C).
4. Charge shaver for 24 hours before its first use. This first charge is important to the
shaver’s battery life.
Note: During the initial charge ignore the electronic indicators as they are
in “Start Up Cycle”.
5.
CAUTION
• Make sure the shaver and your hands are dry when charging the shaver.
• Always charge the shaver in a cool, dry place.
SHAVING
1. Press power button to turn on.
2. Shave face and neck using short, circular strokes.
3. After shaving, turn the shaver off.
SHAVING TIPS
• Remington’s Barber’s Best Pro Power Shaver is showerproof. You may use shaving
foam or gel with your shaver. You may also shave in the shower.
• Wait at least 15 minutes after getting up before shaving, to ensure your face is free
of puffiness that may be present from sleeping.
• Always hold the shaver at a right angle to the skin so that all three heads are
touching the skin with equal pressure.
• Stretch skin with the free hand so hairs stand upright, making it easier for them to
enter the cutting chamber.
• Use moderate to slow, circular stroking movement.
• The use of short, circular motions in stubborn areas may obtain a closer shave,
especially along the neck and chin line.
• Do not press hard against the skin to avoid skin irritation and/or damage to the rotary heads.
Note: When using the shaver with foams or gels it is important to rinse the
cutting head clean after each use. This will avoid having the foam or gel dry in
the cutting head and clogging the shaver.
C

7
TRIMMING
Beard Trimmer:
To remove the shaver head, simply pull upwards from the neck of the shaver for easy
release. To attach the beard trimmer attachment, align it with the neck attachment cavity
so that it clips into position. The beard trimmers micro setting zoom comb can be adjusted
to suit your required length setting, between 2-6mm. The setting can be adjusted by
turning the wheel either left or right.
Without the beard comb attachment, the length of hair cut will be 0.4mm.
Pop-up Trimmer:
1. Push trimmer release button to engage trimmer (Diagram D).
2. Trim sideburns and facial hair.
3. Close trimmer by pressing down (Diagram E).
FACIAL CLEANSING
The daily cleansing facial brush is infused with charcoal to remove impurities and energise
the skin.
TO ATTACH & REMOVE THE FACIAL BRUSH:
• Hold the handpiece with one hand.
• With the other hand, gently pull the shaver head attachment head upwards until it
comes off.
• To attach the facial brush attachment, gently push the brush down aligning it with
the cavity opening until it locks in place. Gently wriggle the attachment head to
ensure it is locked in place, if it comes loose gently remove the head and realign it
until it is snugly attached to the handpiece.
• To remove the facial brush attachment, gently pull the head upwards until it comes off.
CLEANSING TIPS:
Add a drop of facial cleanser to the brush head and dampen under the faucet or shower.
Press on/off button to turn on. Divide your face into 4 main sections; forehead, nose and
chin, left cheek, right cheek. While applying gentle pressure, move the rotating brush in
circular motions over each section for approximately 30 seconds.
D E

Article Price each
AUD
Price each
NZD Qty Amount
$ $ $ $ $
Face Saver: Pre-shave Powder Stick
SP5 $11.95 AUD $14.95 NZD
$ $ $
Sub Total
Postage &
handling
TOTAL
7.50
Replacement
Shaving Heads & Cutters for XR1475AU
SPR-XR1475AU $49.95 AUD
SP4
Shaver Saver: Aerosol Spray Cleaner
$11.95 AUD $14.95 NZD
Daily Cleansing Brush Infused with Charcoal
SPR-XFNAU $14.95 AUD $19.95 NZD
Replacement Beard Trimmer Attachment for XR1475AU
SPR-XTAU $37.95 AUD N/A
$54.95 NZD
Remington is a Registered Trademark of Spectrum Brands, Inc., or one of its subsidiaries.
Spectrum Brands Australia Pty Ltd Locked Bag 3004 Braeside, VIC 3195 AUSTRALIA
IMPORTANT: Pricing in effect at time of publication, inclusive of GST. Subject to change without notice. Postage & handling $7.50 standard for Australia & New Zealand.

CLEANING & CARE
NOTE: When cleaning your shaver, make sure the shaver is turned off and
disconnected from the power cord.
The shaver is a washable appliance. The head and body may be cleaned under warm water.
CAUTION
• When cleaning the external surfaces of the shaver, do not use strong
detergents or other chemicals.
• To dry, wipe the surface of the shaver with a dry towel. Do not use a
hair dryer or heater to dry the shaver.
NOTE: The shaver head and neck assembly is designed to be detachable
from the shaver body. Simply pull upwards from the neck of the shaver for
easy release. To reattach neck, align it with the neck attachment cavity so
that it clips back into position.
SHAVER PARTS
DAILY CLEANING
1. Locate the detachment grooves on the head & cutter assembly. Gently pull to
detach the hair pocket from the neck assembly (Diagram F).
2. Tap out excess hair shavings.
3. Rinse the head of the shaver in running water.
4. Gently reattach the hair pocket to the neck assembly until it locks in place on
all three sides. The hair pocket may be reattached in any configuration.
10
1. Head & cutter (hair pocket) assembly
2. Detachment grooves
3. Neck assembly
4. Neck attachment cavity
5. Beard trimmer attachment
6. Adjustable stubble comb
123
5
4
6