Remington XR1470AU User manual

2 YEAR WARRANTY
To register your product go to
remington-products.com.au
remington.co.nz
XR1470AU
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
ULTRA FLEX
POWER SHAVER

2
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should
always be observed, including the following.
READ ALL INSTRUCTIONS BEFORE USING
For additional protection, the installation of a residual
current device (rcd) having a rated residual operating
current not exceeding 30 mA is advisable in the electrical
circuit supplying the bathroom. Ask your installer for advice.
WARNING - TO REDUCE THE RISK OF BURNS,
ELECTROCUTION AND FIRE OR INJURY TO PERSONS
DANGER - As with most electrical appliances, electrical
parts are electrically live even when the switch is off.
• The appliance should never be left unattended when plugged
into a power outlet, except when charging the appliance.
• This appliance should not be used by children or other
persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge unless they have
been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning
and use maintenance shall not be made by children without
supervision.
• Never operate this appliance if it has a damaged cord or
plug, if it is not working correctly, if it has been dropped or
damaged, or dropped into water. If the supply cord or plug
of the appliance is damaged it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard. It cannot be repaired. Keep the
cord away from heated surfaces.
• Charge, use and store the product at a temperature between
0°C and 32°C.

3
• Do not use outdoors or where aerosol (spray) products are
being used, or where oxygen is being administered.
• Do not use this appliance with damaged or broken tracks or
cutters, as injury may occur.
• Do not plug or unplug the appliance with wet hands.
• For household use only.
• Do not place or store the appliance or charging adaptor
where it can fall or be knocked into a sink or bath.
• Do not place in or drop into water or any other liquid.
• If an appliance falls into water, “unplug it” immediately. Do
not reach into the water.
• Unplug the charging adaptor from the electrical outlet
immediately after fully charging.
• Unplug and switch off this appliance before cleaning it.
• Use this appliance only for its intended use as described in
this manual.
• Do not use attachments not recommended by Remington.
• Never drop or insert any object into any opening of this
appliance.
• Always store the charging adaptor in a moisture-free
location.
• Do not use on people who are asleep.
• Do not use an extension cord or a voltage converter with this
appliance.
• Do not wrap the cord around the appliance.
Remington strongly recommends that an approved Safety Switch
(Residual current device) be installed to protect all bathroom
power outlets. Ask an electrical contractor for advice.
SAVE THESE INSTRUCTIONS

4
XR1470AU ULTRA FLEX POWER SHAVER USE & CARE MANUAL
Thank you for purchasing your new Remington®Ultra Flex Power Shaver.
Inside this manual you will find tips on using and caring for your shaver.
5
6
1
4
3
1. 360° Pivoting Neck
2. Full Floating Heads
3. Pop Up Trimmer
4. On/Off & Turbo Push button
5. LCD Display
6. Charging Pins
Also Includes:
• Charging Stand
• Head Guard
• Storage Pouch
• Cleaning Brush
• Power Adaptor
KEY PARTS
2

5
XR1470AU SPECIFICATIONS
Power System Cordless
Initial Charge Time 24 Hours
Full Charge Time 90 Minutes
Cordless Run Time 60 Minutes
Quick Charge Yes
Turbo Function Yes
Indicators LCD Digital Battery Indicator
LCD Turbo Function Indicator
Worldwide Voltage Yes
Charging Stand Yes
Travel Lock Yes
Shaver Head Replacement Part No. SPR-XR1470AU
Power System
The XR1470AU shaver can only be used without the power cord. The shaver will
not run while it is charging on its charging stand.
Quick Charge
The quick charge allows placing the shaver on charge for 5 minutes and will deliver
up to 5 minutes of use - approximately one or two shaves.
Turbo Function
Press the power button once to activate standard shave speed. This speed is
intended for daily shaving or finer beards. Press the power button twice to activate
the turbo function, this increases the motor RPM by 10% to provide a more
powerful shave. The turbo function is intended for shaving a two or three day beard
growth and provide added power to heavier areas of the beard.
LCD Indicator
Displays the number of minutes of remaining battery power and displays when the
turbo function is on.
Worldwide Voltage
Shaver automatically adapts to an outlet voltage between 100V and 240V.
Note: Some countries will require the use of a plug adaptor that is not
included with your shaver.

6
Folding Charging Stand
Rotate open to hold the shaver while charging. The stand collapses down around
shaver for travel or storage.
Travel Lock
To engage the travel lock press and hold the on/off button for 3 seconds. The LCD
display will flash 5 times to indicate the lock is set. While the travel lock is set, if the
on/off button is pressed the LCD display will flash 3 times to indicate the shaver is
on travel lock mode. To turn the travel lock off, press and hold the on/off button for
3 seconds. The LCD display will flash 3 times while the button is being pressed and
then the shaver will turn on.
CHARGING
1. Plug power cord adaptor into the charging stand (Diagram A).
2. Place the shaver into the charge stand (Diagram B).
3. Plug the adaptor into the wall outlet (Diagram C).
4. Charge shaver for 24 hours before its first use. This first charge is important
to the shaver’s battery life.
Note: During the initial charge ignore the electronic indicators as
they are in “Start Up Cycle”.
CAUTION
• Make sure the shaver and your hands are dry when charging the shaver.
• Always charge the shaver in a cool, dry place.
SHAVING
1. Press power button to turn on.
2. Shave face and neck using short, circular strokes.
3. After shaving, turn the shaver off.
C

7
SHAVING TIPS
• Remington Ultra Flex Power Shavers are showerproof. You may use shaving
foam or gel with your shaver. You may also shave in the shower.
• Wait at least 15 minutes after getting up before shaving, to ensure your face
is free of puffiness that may be present from sleeping.
• Always hold the shaver at a right angle to the skin so that all three heads are
touching the skin with equal pressure.
• Stretch skin with the free hand so hairs stand upright, making it easier for
them to enter the cutting chamber.
• Use moderate to slow, circular stroking movement.
• The use of short, circular motions in stubborn areas may obtain a closer
shave, especially along the neck and chin line.
• Do not press hard against the skin to avoid skin irritation and/or damage to
the rotary heads.
Note: When using the shaver with foams or gels it is important to rinse
the cutting head clean after each use. This will avoid having the foam or
gel dry in the cutting head and clogging the shaver.
TRIMMING
Pop-up Trimmer:
1. Push trimmer release button to engage trimmer (Diagram D).
2. Trim sideburns and facial hair.
3. Close trimmer by pressing down (Diagram E).
D E

Article Price each
AUD
Price each
NZD Qty Amount
$
Face Saver: Pre-shave Powder Stick
SP4 SP5 $11.95 AUD $14.95 NZD $
$ $ $ $
Sub Total
Postage &
handling
TOTAL
7.50
R
Shaver Saver: Aerosol Spray Cleaner
eplacement
Shaving Heads & Cutters for XR1470AU
SPR-XR1470AU
$11.95 AUD $39.95 AUD
$14.95 NZD $49.95 NZD
Remington is a Registered Trademark of Spectrum Brands, Inc., or one of its subsidiaries.

CLEANING & CARE
NOTE: When cleaning your shaver, make sure the shaver is turned off and
disconnected from the power cord.
The shaver is a washable appliance. The head and body may be cleaned under warm water.
CAUTION
• When cleaning the external surfaces of the shaver, do not use strong
detergents or other chemicals.
• To dry, wipe the surface of the shaver with a dry towel. Do not use a
hair dryer or heater to dry the shaver.
NOTE: The shaver head and neck assembly is designed to be detachable
from the shaver body. Simply pull upwards from the neck of the shaver for
easy release. To reattach neck, align it with the neck attachment cavity so
that it clips back into position.
SHAVER PARTS
DAILY CLEANING
1. Locate the detachment grooves on the head & cutter assembly. Gently pull to
detach the hair pocket from the neck assembly (Diagram F).
2. Tap out excess hair shavings.
3. Rinse the head of the shaver in running water.
4. Gently reattach the hair pocket to the neck assembly until it locks in place on
all three sides. The hair pocket may be reattached in any configuration.
10
1. Head & cutter (hair pocket) assembly
2. Detachment grooves
3. Neck assembly
4. Neck attachment cavity
1234