Remocon HCD900 Installation manual

1
REMOCON Duplicator HCD900
Operation manual
HCD-900 Accessories
HCD-900 Console Duplicating Cable(attached)
AC/DC Power Adaptor(attached) Updating Cable (Optional)
Frequency Tuning Bar (Optional)

2
1. Plug in the power adapter into power outlet and push power switch on.(Fig.1)
Caution: Do not put the duplicator on the metal surface while operating, and keep
interference away while operating.
2. LCD screen displays Main Menu.(Fig. 2)
Fig. 1 Fig.2
Remark: Press &to move highlight to desired mode and press Confirm. If you
would like to return to MAIN MENU after entering, press Cancel .
3. Function instruction
3-1. Frequency Meter (Fig. 3)
3-1-1. Func.: Read emitting frequency from remote controls.
3-1-2. Place original remote control on the Test Area of HCD900, and press any key
of remote control. The “Measuring”keeps flashing while reading the
frequency, and then shows the reading of frequency.(Fig. 4)
Fig. 3 Fig. 4
REMOCON
Version 3001.10
MAIN MENU
Frequency Meter
FixedCode Duplicate
HoppingCode Duplicate
REMOCON Read Back
Code Checking
Make Hopping
Setting
Frequency Meter
0.0Mhz
MAIN MENU
Frequency Meter
FixedCode Duplicate
HoppingCode Duplicate
REMOCON Read Back
Code Checking
Make Hopping
Setting
Fn
Confirm
Cancel
Test
Area
Frequency Meter
Measuring
433.7Mhz

3
3-2. Fixed Code Duplicate: No.1 to No. 5 are for frequency band 1, and No. 6 to
No.10 are for frequency band 2(dual frequency). (Fig. 5)
3-2-1. Func.: Read and duplicate fixed
code from original remote control
into REMOCON remote control. It
provides 10 key spaces.(Fig. 5)
3-2-2. Places original transmitter on the
Test Area of HCD900.
Fig. 5
3-2-3. Press and holding 1st button of
original remote control, LCD
displays “Processing”. Releases
the button when beep. Now the
frequency of original remote is
shown above the number 1, and
the code of the 1st button of original
remote has been read
successfully.(Fig. 6)
Fig. 6
3-2-4. Repeat step 3-2-3. until all keys of
original remote control have been
read by HCD900.(Fig. 7)
[Note: for dual frequency remotes
RMC-552, RMC-556 & RMC-558: No.1 to
No. 5 are for buttons 1 to 5 when the
switch position is “Up”, and No. 6 to No. 10
are for buttons 1 to 5 when the switch
position is “Down”; for RMC-558C:
opposite to above]
Fig. 7
3-2-5 (Only for dual frequency remote)
After all keys of 2 remotes with
different frequencies has been read
by HCD-900, press & to move
highlight to No.1 ~ No.5 and No.6 ~
No.10 to choose the right frequency
channels on REMOCON remote by
pressing & .(Fig.8)
Fig. 8 3-2-6. Press Confirm to enter duplicating
mode, the LCD displays as (Fig. 9)
FixedCode Duplicate
12 3 4 5 6 7 8 9 10
10 key spaces remain
Ready
FixedCode Duplicate
433.9
1 23 4 5 6 7 8 9 10
1
9 key spaces remain
Ready
FixedCode Duplicate
433.9
1 2 3 4 56 7 8 9 10
1111
6 key spaces remain
Ready
FixedCode Duplicate
433.9
1 2 3 4 5 6 7 8 9 10
11112222
6 key spaces remain
Ready

4
3-2-7. Connects B or C type REMOCON remote
control & HCD900 by using attached
cable.
Fig. 9
3-2-8. Press Confirm to program the code
into REMOCON remote control.
LCD displays duplication result as
Programming Success or
Programming Failure.(Fig. 10)
Fig.10
3-3. Hopping Code Duplicate:(Fig. 11)
3-3-1. Func.: Read and duplicate hopping
code from original remote controls
into REMOCON remote controls.
Fig. 11
Caution: Some brands of hopping code remote controls were required to input “seed
code”before going to next step. To input “seed code”, please follow the
steps below:
a. Touch Fn & simultaneously.
b. LCD displays “Receiving seed code”.(Fig. 12)
c. You can probably find the seed code button on the rear of original
remote control. It might be hidden in an eyelet. If so, you need a
acicular object to poke it for transmitting the seed code.
d. The LED displays (Fig. 13) when the “seed code”was received.
Fig. 12 Fig. 13
FixedCode Duplicate
433.9
1 2 3 4 56 7 8 9 10
1111
6 key spaces remain
Please Connect Remote
FixedCode Duplicate
1 2 3 4 56 7 8 9 10
1111
6 key spaces remain
Programming success
HoppingCode Duplicate
12 3 4 5 6 7 8 9 10
10 key spaces remain
Please enter 1st code
HoppingCode Duplicate
12 3 4 5 6 7 8 9 10
10 key spaces remain
Receiving seed code
HoppingCode Duplicate
12 3 4 5 6 7 8 9 10
10 key spaces remain
Processing
Please enter 1st code

5
3-3-2. Place the original remote control
on the Test Area of HCD900.
3-3-3. Press and holding 1st button of
original remote control, LCD
displays a serial number(Fig. 14).
Each remote control has its own
series number.
Fig. 14
3-3-4 Press and holding 1st button of
original remote control again. The
LCD displays as Fig. 15.
Fig. 15
3-3-5. Press Confirm , the LCD displays as
Fig. 16. Now the 1st button has been
stored successfully
fig.16
3-3-6. Press and holding 2nd button of original
remote control, LCD displays as (Fig. 17)
3-3-7. Repeat step 3-3-6. to store other keys
of original remote control.
Fig. 17
3-3-8. Connect the H series REMOCON
remote control & HCD900 by using
attached cable.
3-3-9. Press Confirm to program the
code into REMOCON remote control.
3-3-9. LCD displays duplicating result as
Programming Success or
Programming Failure.(Fig. 18)
Fig. 18
HoppingCode Duplicate
12 3 4 5 6 7 8 9 10
10 key spaces remain
Microchip HC5300
2 A72282F 24DC5718
Please enter 2nd code
HoppingCode Duplicate
12 3 4 5 6 7 8 9 10
10 key spaces remain
Serial Number Setting
0022293
HoppingCode Duplicate
123 4 5 6 7 8 9 10
1 9 key spaces remain
Please enter 1stcode
HoppingCode Duplicate
1234 5 6 7 8 9 10
11 8 key spaces remain
Please enter 1stcode
HoppingCode Duplicate
1234 5 6 7 8 9 10
11 8 key spaces remain
Programming success
Please enter 1stcode

6
3-4. REMOCON Read Back (For FixedCode)
3-4-1 Func.: To read the code from REMOCON remote control, and reduplicate the code
into other REMOCON remote controls. 3-4-2. Be sure to connect REMOCON
remote control(existing code) to
HCD900 by using attached cable
before entering “REMOCON
Read Back”mode. (Fig. 19)
Fig. 19
3-4-3. Move highlight to “REMOCON
Read Back”mode, press Confirm
to start reading. The LCD displays
as Fig. 20.
Fig. 20
3-4-4. Replace the remote control by new REMOCON remote control and touch
Confirm. LCD displays duplication result as Programming Success or Programming
Failure.
3-5. Code Checking(Fig. 21)
3-5-1. Func.: There are 2 functions in
this mode: First is to verify
whether the duplication has
been done successfully or not;
Second is to identify your
existing remote control is fixed
code or hopping code.
Fig. 21
3-5-2. To verify if the duplication has
been done successfully, press
1st button of original remote
control till beep.
3-5-3 The LCD appears “Processing”
and goes to Fig. 22.
Fig. 22
MAIN MENU
Frequency Meter
FixedCode Duplicate
HoppingCode Duplicate
REMOCON Read Back
Code Checking
Remote Report
FixedCode Duplicate
1 2 3 4 56 7 8 9 10
1111
6 key spaces remain
Ready
Code Checking
Please Enter 1st Code
Press cancel To Exit
Code Checking
Please Enter 2nd Code
Press cancel To Exit

7
3-5-4. Press 1st button of the duplicate,
HCD900 starts to check the
contrast, and then shows the
similarity percentage.(Fig. 23)
Fig. 23 3-5-5. Follow steps 3-5-2, 3-5-3 &3-5-4 to
verify other buttons.
3-5-6. To identify whether the remote control is fixed code or hopping code, press
1st button of the remote control. (Fig. 21)
3-5-7. The LCD appears “Processing”and goes to Fig. 22.
3-5-8. Press same button again. HCD900 starts to check the contrast, and then
shows the similarity percentage.(Fig. 23)
3-5-9. Hopping code remote control will result 0.0 percent matched.
Caution: The qualified duplication requires at least 90% similarity.
3-6 Make Hopping: Create a duplicate without the existing of original rolling code
remote control. (This function can only be used to create original
remotes with HCSxxx format of IC and the original remotes
without seed code)
3-6-1. Press and to choose the
brand what you would like to
clone. (Fig. 24)
Fig. 24 3-6-2. Press to enter the Reference
Number Setting.
Press and to set up the
reference number. (Only need to
set up for certain brands) (Fig. 25)
Fig. 25
3-6-3. Press Confirm to enter the
Serial Number Setting.
Press and to set up the
serial number. (Fig. 26)
Code Checking
Please Enter 1st Code
99.2
Percent Matched
Press cancel To Exit
Make Hopping
FADIN 00
Make Hopping
FADIN 01
Make Hopping
Serial Number Setting
0000001
FADIN 01

8
Fig. 26
3-6-4. Press Confirm to ready to copy.
Connect REMOCON rolling code
remote to HCD-900 by using
attached cable. (Fig. 27)
Fig. 27
3-6-5. Press Confirm to program the
code into REMOCON remote
control. LCD displays duplication
result as Programming Success or
Programming Failure.(Fig. 28)
Fig. 28
＊＊＊Notice: If the REMOCON remotes you prepare to copy the original remotes are
using 3V battery, please connect it to our HCD-900 by duplicating cable before you read
code from original remote to HCD-900.＊＊＊
Revised at Feb.,25,2016
HoppingCode Duplicate
12 3 4 5 6 7 8 9 10
2 4 9 D D 6 B F D D
0 key spaces remain
Press Confirm To Copy
HoppingCode Duplicate
12 3 4 5 6 7 8 9 10
2 4 9 D D 6 B F D D
0 key spaces remain
Programming Success
Press Confirm To Copy