Remote Control MARANTEC D343 Owner's manual

http://www.remotecontrol-
express.com
Connection of the receiver to the motor:
1. Unplug your motor.
2.
Check that your receiver is supplied with a 12 or 24 power
by the circuit board of your motor is greater (for example, 220 ), you will have to install a
transformer.
3.
Make the following connections with the electric
-Connect channel 1
betwee
the hole under the screws and then screw them to lock the wire).
-
Connect channel 2 between terminals 7 and 8 on the receiver
connection of this channel is not displa
-
Connect the terminal + of the motor (or terminal with a tension indication) to terminal 5 on
the receiver.
-Connect the terminal –
or GMD of the motor to
4.
Your receiver is connected.
Receiver already in use and to be kept
(example of configuration)
Main receiver card
Programming Manual
express.com
- TEL : [phone] - FAX :
44 (0) 207 927 3151
MARANTEC D343 – D344
Connection of the receiver to the motor:
Check that your receiver is supplied with a 12 or 24 power
supply.
If the voltage delivered
by the circuit board of your motor is greater (for example, 220 ), you will have to install a
Make the following connections with the electric
al wires as
indicated in the diagram above
betwee
n terminals 2 and 3 on the receiver
(you have to insert the wire in
the hole under the screws and then screw them to lock the wire).
Connect channel 2 between terminals 7 and 8 on the receiver
(
for more clarity, the
connection of this channel is not displa
yed in the diagram above).
Connect the terminal + of the motor (or terminal with a tension indication) to terminal 5 on
or GMD of the motor to
terminal 4
on the receiver
Your receiver is connected.
Receiver already in use and to be kept
(example of configuration)
Main receiver card
44 (0) 207 927 3151
If the voltage delivered
by the circuit board of your motor is greater (for example, 220 ), you will have to install a
indicated in the diagram above
:
(you have to insert the wire in
for more clarity, the
Connect the terminal + of the motor (or terminal with a tension indication) to terminal 5 on
on the receiver
.

http://www.remotecontrol-
express.com
Programming of the
first remote control with
1.
Open the casing of your receiver.
2.
On the receiver circuit board, press the button
3.
Press a button on your new remote control. Keep it pressed down. The LED light L1
illuminates fixedly. Let the button on your new remote control go.
4. Wait 10 seconds.
5.
Your new remote control is programmed.
Programming of the following remotes:
1.
Connect the old and the new remote control with the supplied broach (diagram above).
2. Press a
button on your old (or already
The LED light on your old remote control illuminates.
3.
While keeping the button on your already
the button you wish to program on
light on
your new remote control blinks and then illuminates fixedly. Let the buttons go.
4.
Repeat this procedure for each button you wish to program.
5. Wait 10 seconds.
6.
Your new remote control is programm
Programming Manual
express.com
- TEL : [phone] - FAX :
44 (0) 207 927 3151
first remote control with
the receiver:
Open the casing of your receiver.
On the receiver circuit board, press the button
CH1
. Let it go. The LED light L1 blinks.
Press a button on your new remote control. Keep it pressed down. The LED light L1
illuminates fixedly. Let the button on your new remote control go.
Your new remote control is programmed.
Programming of the following remotes:
Connect the old and the new remote control with the supplied broach (diagram above).
button on your old (or already
-
programmed) remote control. Keep it pressed down.
The LED light on your old remote control illuminates.
While keeping the button on your already
-programmed remote control
the button you wish to program on
your new remote control. Keep i
t pressed down. The LED
your new remote control blinks and then illuminates fixedly. Let the buttons go.
Repeat this procedure for each button you wish to program.
Your new remote control is programm
ed.
44 (0) 207 927 3151
. Let it go. The LED light L1 blinks.
Press a button on your new remote control. Keep it pressed down. The LED light L1
Connect the old and the new remote control with the supplied broach (diagram above).
programmed) remote control. Keep it pressed down.
pressed down, press
t pressed down. The LED
your new remote control blinks and then illuminates fixedly. Let the buttons go.