Renkus-Heinz PF1-500 User manual

Instruction Manual
Installing
PF1-500 & PF1-500R Ampli ers
Into CFX Series Subwoofers
19201 Cook Street, Foothill Ranch, CA USA
Phone: [phone] • Fax: [phone]
[email protected] • www.renkus-heinz.com
RH 734 August 2011

Photos of the CFX15S were used in
these instructions. The procedure for
installing these ampliers into CFX12S
and CFX18S subwoofers is the same.
Step 1
Use a Phillips screwdriver to remove the
screws holding the connector plate in
place and carefully remove the connec-
tor plate. Save the screws. You’ll need
them to install the amplier.
Step 2.
Disconnect the white 2-pin connector
from the connector plate by squeezing
the sides of the connector and pulling.
Step 3
Set the connector plate aside and save
it in case you ever need to switch the
subwoofer back to a non-powered unit
Step 4
If you are installing a PF1-500, set the
slide switch on the top of the amplier
case to “100 Hz Filter”. to activate the
amplier’s electronic crossover network
(100 Hz lo-pass lter) and protective
circuitry.
Connect the white 2-pin connector to
the amplier.
Step 5.
If you are installing a PF1-500R locate the
Crossover Network and the white 4-pin con-
nector that connects it to the woofer. You will
nd the crossover attached to the bottom of
the cabinet.
Step 6
Disconnect the white 4-pin connector from the
Crossover Network by squeezing the sides of
the connector and pulling.
Step 7.
Connect the white 4-pin connector to the
amplier. Make sure that both sides of the
connector latch into place.
Note that this bypasses the Crossover Net-
work and it no longer will have any effect on
the subwoofer’s performance. The output of
the amplier is now connected directly to the
woofer and RHAON is now in control of the
subwoofer’s performance.
Step 8.
Carefully slide the amplier into the cabinet
and use the Phillips head screws to secure it
in place.
Page 2 Page 3
CF/CFX15S CF/CFX15S

Photos of the CFX15S were used in
these instructions. The procedure for
installing these ampliers into CFX12S
and CFX18S subwoofers is the same.
Step 1
Use a Phillips screwdriver to remove the
screws holding the connector plate in
place and carefully remove the connec-
tor plate. Save the screws. You’ll need
them to install the amplier.
Step 2.
Disconnect the white 2-pin connector
from the connector plate by squeezing
the sides of the connector and pulling.
Step 3
Set the connector plate aside and save
it in case you ever need to switch the
subwoofer back to a non-powered unit
Step 4
If you are installing a PF1-500, set the
slide switch on the top of the amplier
case to “100 Hz Filter”. to activate the
amplier’s electronic crossover network
(100 Hz lo-pass lter) and protective
circuitry.
Connect the white 2-pin connector to
the amplier.
Step 5.
If you are installing a PF1-500R locate the
Crossover Network and the white 4-pin con-
nector that connects it to the woofer. You will
nd the crossover attached to the bottom of
the cabinet.
Step 6
Disconnect the white 4-pin connector from the
Crossover Network by squeezing the sides of
the connector and pulling.
Step 7.
Connect the white 4-pin connector to the
amplier. Make sure that both sides of the
connector latch into place.
Note that this bypasses the Crossover Net-
work and it no longer will have any effect on
the subwoofer’s performance. The output of
the amplier is now connected directly to the
woofer and RHAON is now in control of the
subwoofer’s performance.
Step 8.
Carefully slide the amplier into the cabinet
and use the Phillips head screws to secure it
in place.
Page 2 Page 3
CF/CFX15S CF/CFX15S

Instruction Manual
Installing
PF1-500 & PF1-500R Ampli ers
Into CFX Series Subwoofers
19201 Cook Street, Foothill Ranch, CA USA
Phone: [phone] • Fax: [phone]
[email protected] • www.renkus-heinz.com
RH 734 August 2011