Renu Electronics WP6 Plus Web HMI Series User manual

User Manual
WP6 Plus Web HMI Series®

WP6 Plus Web HMI Series
© RENU Electronics Pvt. Ltd. Page 2of 23
Table of Contents
INTRODUCTION...............................................................................................................................................................3
BEFORE YOU START .....................................................................................................................................................3
SAFETY PRECAUTIONS.................................................................................................................................................4
PRODUCT OVERVIEW....................................................................................................................................................5
INSTALLATION OF THE WEB HMI PRODUCTS......................................................................................................................5
PRODUCT SPECIFICATIONS...............................................................................................................................................8
PRODUCT NOMENCLATURE /ORDERING PART NUMBER.....................................................................................................8
DISPLAY SPECIFICATIONS.................................................................................................................................................8
CPU, MEMORY AND POWER SUPPLY................................................................................................................................9
COMMUNICATION INTERFACES........................................................................................................................................10
DEFAULT PRODUCT SETTINGS..................................................................................................................................11
ENVIRONMENTAL SPECIFICATIONS AND APPROVALS ........................................................................................................11
POWERING UP THE WEB HMI SERIES.......................................................................................................................12
GETTING STARTED WITH THE WEB HMI...................................................................................................................12
MAIN SETTINGS .............................................................................................................................................................12
ENTERING INTO DEVICE SETTINGS...................................................................................................................................13
ON-SCREEN KEYBOARD SETTING...................................................................................................................................18
WEB APPLICATION.........................................................................................................................................................19
REVISION HISTORY......................................................................................................................................................22
NOTES............................................................................................................................................................................23

WP6 Plus Web HMI Series
© RENU Electronics Pvt. Ltd. Page 3of 23
Introduction
The Web HMI is a ThinClient with an inbuilt browser which connects to a remote web server on
its network.
All WP6 Plus devices are compliant with EMC directive 2014/30/EU and LVD directive
2014/35/EU and certified for UL Class I Div. 2.
This user manual gives a detailed information regarding the hardware specifications, operating
conditions, installation, mounting and wiring. All the information published in this manual is
produced and governed by RENU Electronics Pvt. Ltd. and is protected by Indian Copyright Act.
Before you start
RENU Electronics Pvt. Ltd is not responsible or liable for any indirect or consequential
damage resulting from the use of this product.
The user should check and confirm the suitability of the product before using in any specific
application.
The diagrams and examples in this manual are included for illustration purposes only. RENU
Electronics assume no responsibility or liability regarding actual use based on the diagrams
or examples shown.
Reproduction of the contents of this manual, in any form (in part or in whole), is strictly
prohibited.
Following table shows various symbols that may be used in this manual to provide information
regarding safety, precautions and usage of the product:
WARNING: Indicates circumstances that may cause an explosion in hazardous
environment, which may lead to injury or death, damage or economic loss
CAUTION: Indicates specific precautions to be taken by user during installation,
operation and maintenance of the product
ATTENTION
ATTENTION: Indicates important information regarding application and functions of
the product

WP6 Plus Web HMI Series
© RENU Electronics Pvt. Ltd. Page 4of 23
Safety Precautions
This section of the manual provides information which is critical regarding safety and therefore
the user is advised to go through the information in detail before installing the product. User may
contact RENU Electronics’technical support team at [email protected] for any
specific question(s) related to safety.
WARNING: EXPLOSION HAZARD
Do not disconnect equipment unless power has been removed or the area is known
to be non-hazardous.
Substitution of any component may impair suitability for Class I, Division 2.
Secure any external connections that are made to this equipment by using screws,
sliding latches, threaded connectors or any other means provided with this product.
If this product contains batteries, they must only be changed in an area known to be
nonhazardous.
CAUTION: GENERAL PRECAUTIONS
Do not use this product for emergency stop. A separate physical switch, outside the
product must be used for any emergency stop operations.
Do not use the external power supply source that does not comply with the specified
power requirements of the product, it may cause malfunction or permanent damage
to the product.
Do not attempt to open, dismantle or modify the product, doing so will void the
warranty.
This product is supplied as open-type equipment and it must be mounted within an
enclosure, suitably designed for specific environmental conditions.
When used in Class I, Division 2 hazardous location, the product must be mounted
in a suitable enclosure with proper wiring method that complies with the governing
electrical codes.
The USB port is intended for temporary local programming purposes only and not
intended for permanent connection. If you connect or disconnect the USB cable with
power applied to this product or any other device on USB network, and electrical arc
can occur, which could cause explosion in hazardous location installations.
Make sure that connectors are securely tightened to properly seal the connections
against leaks.
Do not place the product in direct sunlight. Prolonged exposure to sunlight may
degrade the LCD and housing.

WP6 Plus Web HMI Series
© RENU Electronics Pvt. Ltd. Page 5of 23
Product Overview
This section of the manual provides an overview of Web HMI series products, its front and back view, installation
details, dimensional details, mounting method and details.
Installation of the Web HMI products
Web HMI series products are designed for front panel mounting. Before installing the products, user should review
the panel guidelines, panel cutout dimensions, product dimensions and minimum clearances.
Panel Guidelines
The panel must be at least 2mm (12 gauge), in order to provide the required support and proper sealing against
water and dust. The panel surface must be flat, devoid of any imperfection, to maintain adequate seal and IP rating.
The maximum panel thickness on which this HMI can be mounted is 6mm (±0.2mm).
Panel Cutout Dimensions
Model
Height (mm)
Width (mm)
WP6043TN Plus
80
111
WP6070TN Plus
127
175
WP6101TN Plus
178
256
ATTENTION
ATTENTION: Panel cutout
Before cutting out the panel, disconnect all electrical power from the panel.
Make sure that the area surrounding the panel cutout is clear.
Make sure that metal cutting chips do not enter any other component, already
installed in the panel.
Product Dimensions
This section of the manual provides dimensional details of Web HMI series products. All the dimensions shown
below are measured in mm.
WP6043TN Plus

WP6 Plus Web HMI Series
© RENU Electronics Pvt. Ltd. Page 6of 23
WP6070TN Plus
WP6101TN Plus

WP6 Plus Web HMI Series
© RENU Electronics Pvt. Ltd. Page 7of 23
Minimum Clearances
Maintain minimum clearance of 2” from enclosure walls, wires and other adjacent devices on all sides for adequate
ventilation. Plan for adequate space around the product and inside the enclosure for ventilation and cabling. Take
into consideration the heat produced by other devices in the enclosure. The operating temperature for this product
is between 0° to 50°C. Care should be taken in-order to maintain the ambient temperature around the Web HMI
within this range.
Mounting Web HMI Products
Web HMI series products must be installed on the front panel, using the clamp accessories shipped with the product.
Before mounting, make sure that sealing gasket is properly positioned. This gasket forms a compression type of
seal. Do not use sealing compounds. Place the unit in the panel cutout and tighten the mounting screws evenly
(torque 0.4Nm) to maintain water and dust resistance.
ATTENTION
ATTENTION: Mounting Web HMI on Panel
Do not push directly on the LCD display of the HMI when placing the unit into the
panel as it may damage the display. Push on the bezel or the border of the LCD
display.
Connecting Power
Web HMI series require 24VDC to operate. Follow the steps mentioned below to connect a power supply to the
device:
Make sure that terminal is not connected to power source.
Secure the 24VDC power wires.
Secure the functional earth ground wire to the functional earth ground terminal screw on terminal block.
Apply 24VDC power to the terminal.
Grounding
The optimum method for grounding electronic equipment is to ground it separately from other high-power systems
and to ground more than one unit of electronic equipment with a single-point ground. Following marked terminal is
provided with the unit for grounding:

WP6 Plus Web HMI Series
© RENU Electronics Pvt. Ltd. Page 8of 23
Product Specifications
This section of the manual provides detailed specifications of Web HMI series products, ordering part numbers,
operating conditions, environment and approvals.
Product Nomenclature / Ordering Part Number
Web HMI series has three models, depending on the display size. The detailed part number or ordering information
is as follows:
Display Specifications
Web HMI series products support high quality color TFT display range.
Size: 4.3" Color TFT, WQVGA Web Panel Analog Resistive Touch Screen
Resolution: 480 x 272pixels
Colors: 16M
Brightness: 400cd/m2
Backlight life: 30,000Hrs.
Size: 7” Color TFT, WVGA Web Panel Analog Resistive Touch Screen
Resolution: 800 x 480pixels
Colors: 16M
Brightness: 350cd/m2
Backlight life: 30,000Hrs.
Size: 10.1” Color TFT, WSVGA Color Web Panel Analog Resistive Touch Screen
Resolution: 1024 x 600pixels
Colors: 16M
Brightness: 350cd/m2
Backlight life: 50,000Hrs.
Plus

WP6 Plus Web HMI Series
© RENU Electronics Pvt. Ltd. Page 9of 23
CPU, Memory and Power Supply
Power Rating
Unit
Voltage
Current
Wattage
WP6043TN Plus
24VDC
220mA
5.5W
WP6070TN Plus
24VDC
250mA
6W
WP6101TN Plus
24VDC
350mA
8.5W
CPU: 2xARM Cortex-A9 upto
1GHz with GPU 2D/ GPU 3D
support
eMMC:4GB
RAM:1GB
Power Supply:
24VDC (±15%) with isolation
RTC: Built-in.

WP6 Plus Web HMI Series
© RENU Electronics Pvt. Ltd. Page 10 of 23
Communication Interfaces
This section provides detailed information regarding various communication interfaces supported by the Web HMI
series.
Interfaces
WP6043TN Plus
WP6070TN Plus
WP6101TN Plus
USB Type C
1
1
1
USB Host
1x 2.0
1x 2.0
1x 2.0
RJ45/Ethernet
1x 10/100Mbps
1x 10/100Mbps
1x 10/100Mbps
RJ45/Ethernet Port
The Web Panel HMI series devices come with an in-built RJ45/Ethernet port. The RJ45 port is a shielded female jack
with link and activity LEDs.
Pin number
Signal
1
TX+
2
TX-
3
RX+
4
NC
5
NC
6
RX-
7
NC
8
NC
Type C USB Port
The Web HMI comes with a Type C USB port.
Pin number
Signal
1
GND
5
D-
6
D+
7
D-
8
D+
12
GND