Repotec RPIPA1000 User manual

Antenna Installation
01
2) Indoor Directional Patch Antenna Installation
System Requirements
- 2.4Ghz Wireless Network (IEEE 802.11b or IEEE 802.11g or IEEE 802.11n)
- One Wireless Device with detachable external Antenna connector
- Connector Type : Reverse SMA Female Jack or Reverse TNC Male (Optional)
Package Content
- High Gain Wireless Patch Antenna with Cable
and Reverse SMA Connector 1 Set
- Wall Mounting Screw & Wire Organizing Bracket 1 Set
- Quick Installation Guide 1 PCS
- RP-SMA Female to RP-TNC Male Connector Adapter
(Conversion adapter for Wireless Devices with TNC antenna
connectors) (Optional)
1 PCS
- Rubber Footing 1 Set
Introduction
The high gain indoor wireless patch antenna (hereafter called Indoor Patch
Antenna) is the ideal solution to extend directional coverage and amplify the
signal power of your wireless network. It provides concentrated directional
coverage resulting in a stronger signal but smaller coverage area. The Indoor
Patch Antenna provides the most effective solution in a specified area of
service space and is great for Wireless Access Point and Wireless Network
Adapters and it is simple and easy to setup.
Note: Please take care while adjusting the angle of the
antenna, do not forcefully turn as it will damage the device.
90o90o
Tilt Back
Tilt Front
45o225o
Swivel Left Swivel Right

Antenna Installation
Step 2 : Screw in the SMA Connector from the Indoor Directional Antenna
into the wireless device
Step 3 : After the Indoor Patch Antenna is attached to the wireless
device position the Indoor Patch Antenna vertically to the
desk or wall and choose the optimal location for extending the wireless
coverage area and best performance.
** For desk mount, recommend to place the included rubber footing for a firm placement.
Antenna
Connector
(RPSMA-plug)
Device
Connector
(RPSMA-jack)
Remove and unscrew counter-clockwise
Step 1 : Remove one default antenna from the wireless device by unscrewing
if from the base and start to assemble!
Screw in clockwise the
Reverse SMA plug
Caution
Before installing the Indoor Patch Antenna please make sure the wireless
device antenna either from the Wireless Access Point, Wireless Router,
Wireless PCI Card, Wireless USB Adapter....etc is removable by examining
the base of the antenna to see if it is a screw on type. Please do not force
off an antenna as it will damage the wireless transmission
02
* If your Wireless Router/Access Point has two antennas, it is better not to remove the
second antenna. For optional performance, two High-Gain Antenna should be used,
pointed to different directions.

Antenna Installation
03
Caution : Do not mount the antenna perpendicular to the wall, always
place the antenna vertically to the desk/wall.
The Indoor Patch Antenna is also able to be wall mounted. The included wall mount
screws allows you to place the antenna on the wall which provides the benefits to send
a stronger signal due to less obstruction from objects to create more coverage.
You may also use the enclosed wire organizing brackets to stick onto the walls to
organize cable cluster.
60
Horizontal coverage Vertical coverage
110
Overlook
80
Please base your setup location
from the coverage diagrams
showing the direction and the
region of amplified wireless
signal.
Wall Mount
Incorrect Wall Placement
Vertical Wall Placement
Horizontal Wall Placement

Antenna Installation
04
Electrical Specifications
Antenna Type
Frequency Range
Network Specification
Gain
V.S.W.R
Beam Width-H Plane
Beam Width-E Plane
Polarization
Input Impedance
Connector
Cable
Mounting
Operation Temperature
Storage Temperature
Humidity
2.4GHz 10 dBi Indoor Patch Antenna
2.4 ~ 2.5GHz
IEEE 802.11b , IEEE 802.11g , IEEE 802.11n Network
10 dBi
< 1.5
1100 (Vertical)
Vertical (Linear)
50 Ohms
Reverse SMAMale Plug
RG178 , Length : 100cm
2700Degree Adjustable Stand , Wall Mount or Table Mount
-200C - + 700C
-300C - +850C
95% maximum (non-condensing)
Features
Note:
1. Always place the antenna on a flat
or secure surface.
2. Hiding the antenna behind books, cabinets or other office equipment may
affect the performance of the wireless network.
3. The antenna transmission range may vary due to many factors in the
environment or applications. Performance results will also be affected from
different wireless devices due to the variety of different brands where the
wireless router / access point may vary from one to the next.
600 (Horizontal)
Caution: Avoid direct contact with High Gain Wireless
Signals. Keep a distance when in operation. (1 ft)
- High gain : 10 dBi - Smart,Slim and elegant style
- High performance - 2700 Tilt-and-swivel design for best reception
- Low backward radiation - Versatle Mounting Design
- Low profile - Light-weight