ReproScan 2.0 User manual

• Read these instructions prior to using your ReproScan 2.0 Sunlight Readable Wireless Monitor.
• Contact your ReproScan authorized dealer should you have further questions about the
operation of your new monitor
• For further information, email: [e-mail] or call 1-877-890-2411
ReproScan 2.0 Monitor
Operator’s Manual

ReproScan 2.0 Monitor
Features
●IP63 rated water and dust resistance
●1,000NIT Sunlight Readable with long life LED backlight
●HDMI Input x 1
●VGA Input (15 pin D-SUB) x 1
●Video Input x 1
●8 channel 2.4GHz & 5.8 GHz WIFI video input
●NTSC / PAL Mul-System
●4 : 3 Aspect Rao
●High resoluon display
●Solid Capacitors for improved durability
●Automac backlight level adjustment through built-in ambient light sensor
●High Performance Image and Video Signal Processor
●AISS - Advanced Image-Scaling and Shaping
●Last Input memory
●Last Power seng memory
●Automac display adjustment
●On Screen Display Control
●Mirror Image Flip
●Vercal Image Flip
●Funcon to disable front buon(s)
●Funcon to disable On Screen Text
●An Reecve / Fingerprint Coang
Physical Specicaons
●Video Source Input
— RGB analog male connector ( 15-Pin D-SUB ) x 1
— RCA composite video female connector x 1
— HDMI input connector x 1
— 2.4GHz & 5.8GHz WIFI CVBS video
●Power Source Input
— Single 12V DC_IN ( Supports 12V~24V )
— Baery 11.1V DC
●External Buons Input
—OSD buons for Power / Select / Menu / Increase /
Decrease
—Power buon for power switch
— On/O toggle switch to isolate baery
●Dimension ( In ) : 8.97 ( L ) x 6.69 ( H ) x 2.08 ( D ) In
●Weight ( lb ) : 3.08 lbs ( w/o baery )
Other Specicaons
●Operang Temperature : -4°F ~ 158°F ( Not included
baery )
●Storage Temperature : -22°F ~ 176°F ( Not included
baery )
●FCC, CE, Cercaon
●ROHS Compliant
●IP63 Compliant
Display Specicaons
●Screen Size : Diagonal 8” ( 4 : 3 )
●Physical Resoluon : 800 ( H ) x 600 ( V )
●Pixel Pitch : 0.0675 ( H ) x 0.2025 ( V ) ( in )
●Dot Resoluon : 2400 x 600 = 1,440,000 ( dots )
●Supported Resoluon : 640 x 480 ~ 1920 x 1080
●Supported Refresh : 60~75Hz
●LCD Panel Brightness : 1000 cd/m²
●Contrast Rao : 500 : 1
●Response Time : 10~15ms
●Viewing Angle : Vercal : 120゜/ Horizontal :
140゜
●Colors : 6-bits ( 262,144 colors )
Electrical Specicaons
●Operang Voltage Range : DC 12V ~ 24V
●Power Supply : DC 12V
●Power Consumpon :
— Suspended Mode < 2W ( Max. )
— Connuous Mode < 10W ( Max. )
— Charging Mode < 24W ( Max. )
Page 2

1. Charging your ReproScan 2.0 Monitor
1. Identify “Toggle Switch” beside the VGA connector. Make sure that the switch is: ON TO
CHARGE, ON TO USE THE MONITOR, OFF TO STORE.
2. NOTE: The “Toggle Switch” isolates the battery so it will not discharge during storage.
3. Make sure the battery in the monitor is fully charged before use.
4. To charge, plug in the ReproScan 3 Amp Charger into the 12 DC power in socket as shown.
Connect other end of the charger to 110 VAC (USA/Canada ) or 230 VAC (Australia/NZ/Other),
turn on the “Toggle Switch” (turn off to store monitor and save the battery charge).
5. A full battery charge from dead battery to full battery will take approximately 10 hours.
6. Store monitor with a full charge. Periodically during the off season, charge the battery.
7. Monitor may be used while charging.
3 Amp 12 V DC Charger
2. Video connector cable ports
Insert 110 V or 230 V
cord here
Page 3

3. Understanding the ReproScan 2.0 Monitor Control Buttons
►
PowerSelectMenu
Right
Le
Touch Buttons are at bottom of the monitor display
Page 4
1. Use the Touch Buttons to select the OSD (On-Screen Display) screen with the settings you
wish to change.
2. Touch Buttons are found at the bottom of the screen. The Touch Buttons are:
Power Button : Press to turn ON or OFF the monitor. (Remember the Toggle Switch!)
Select Button : Press to select the input signal to display. (VGA, HDMI, AV, WL-AV)
Menu Button : Press the button to show the OSD menu.
And then press the left ( ◄ ) or right ( ► ) to navigate
through the menu. Press “ Select “ button to go down
through a list of settings and options.
Press the left ( ◄ ) or right ( ► ) buttons to change the
values of settings.
Press Menu button again to leave the OSD menu
Right Button : ( ► ) Press this button to increase Dimmer (Backlight) or a value of settings
inside the OSD menu.
Left Button : ( ◄ ) Press this button to decrease Dimmer (Backlight) or a value of settings
inside the OSD menu.
►

4. To Change Brightness, Contrast and Backlight (Dimmer)
►
PowerSelectMenu
Right
Le
1. Press Power to turn on
the monitor.
2. Press Menu and left
( ◄ ) or right ( ► ) to select
OSD with appropriate
screen
3. For Brightness, Contrast
and Backlight changes use
the Color Screen
4. Press Select to scroll
through Brightness,
Contrast, Backlight
5. Press Left or Right to make
desired changes to
Brightness, Contrast,
Backlight, Sharpness
6. Optimum setting will vary
with ambient light.
7. Press Menu to exit
(This will save the settings).
5. To turn on Battery Level Icon (follow same procedure to change other features)
1. Press Power to turn on
monitor.
2. Press Menu then Left
or Right to go to OSD
screen
3. Press Select to scroll
through to Battery Icon
4. Press Left or Right to
make desired changes
to Battery Icon - On to
show constantly
5. Press Menu twice
slowly to exit (This will
save the settings)
Saturaon, Sharpness and Hue do not change
the black and white ultrasound image.
Page 5
►
PowerSelectMenu
Right
Le

6. To Change the Wireless Channel - XTC and Flexx have wireless capabilities.
• XTC has 8 - 5.8 GHz channels (older XTC models use 2.4 GHz channels)
• Flexx has 8 - 5.8 GHz channels.
1. Press Power to turn on
monitor.
2. Press Menu then Left or
Right to select the
Function screen
3. Press Select to scroll
through Reset, Display,
Sleep, Keypad, Source
Enable to get to Channel
4. Press Left or Right to
make desired changes to
the channel. If you have
to change the ultrasound
sender channel, it may
take a few seconds to see
the image.
5. Press Menu to exit (This
will save the settings)
PoweSelecMen
Right
Le
7. Change the Channel on your XTC by ReproScan - see owner’s manual for more details
The XTC unit has a built in wireless sender. There are 8 channels available. You will need to
match these channels to the monitor channels. Eg. Channel 6 on the XTC matches with Channel
5.8 G: CH 6 on the ReproScan 2.0 Monitor. If you are using a 2018 or older XTC, the channel on
the 2.0 Monitor will start with 2.4G CH# and
another ultrasound such as an Easi-Scan, the
channel numbers will be different so some
experimentation is necessary.
To Change the channel an XTC
1. Connect the ReproScan XTC the monitor with
VGA or AV connector so you can see the
changes.
2. Turn on ReproScan XTC.
3. Press Menu button twice
4. Press Exam to scroll to Wireless - make sure
Wireless is set to ON - Press + to turn on
5. Press Exam to scroll to Channel - use + or - to
select desired channel (0,1,2,3,4,5,6,7)
6. Set Monitor to WL - AV (this indicates Wireless
receiver is turned on) and check to see that
Channel setting on your ReproScan XTC is the
same as the Channel setting on the monitor.
Page 6

8. Change the Channel on your Flexx by ReproScan - see owner’s manual for more details
The Flexx has a built in wireless sender. There are 8 - 5.8 GHz channels are available. You will
need to match these channels to the monitor channels. Eg. Channel 6 Flexx matches with 5.8G:
CH6 5925MHz setting on the ReproScan 2.0 Monitor.
To change the channel on a Flexx
1. Turn on the Flexx ultrasound
2. Press Menu button twice
3. Use the Arrow keys to scroll to Other
4. Press the Enter key
5. Use the Arrow keys to scroll to RF5.8G and use
the Arrow key to turn RF5.8G to On.
6. Use the Arrow keys to scroll to Channel.
7. Use the Arrow keys to select the same 5.8GHz
channel that you have selected on the
ReproScan 2.0 Monitor.
8. Press Enter to save and exit Other
9. Press Esc to return to active scanning.
Scroll to Other and press Enter
Page 7

1. Press Power to turn on
monitor.
2. Press Select to scroll
through VGA, AV and
HDMI, WL - AV,
3. Only Enabled Sources
will be displayed
4. If the ultrasound unit is
directed wired with
VGA connectors, select
VGA
5. If may take a few
seconds for the
ultrasound image to
appear on the screen
9. Switch to Direct Wired Connection (VGA or AV) - Enable Source
10. To Change Monitor from Wireless Receiver to a Direct Wired Channel (VGA or AV)
►
PowerSelectMenu
Right
Le
1. Press Power to turn on
monitor.
2. Press Menu then Left
or Right to go to
Function screen
3. Press Select to scroll
through to Source
Enable
4. Press Right display
Source Enable Menu
5. Press Select to select
AV or VGA
6. Press Right or Left to
turn on or off
7. Press Menu 3 times
slowly to save and exit
8. Attach VGA or AV
cable
(Note: VGA uses LEMO
connector to Flexx or XTC)
Press the Select Buon to display VGA, AV,
HDMI or WF—AV
Page 8
►
PowerSelectMenu
Right
Le
Note:
Use VGA for most direct wired applications.
Use WF - AV for wireless applications.
Use AV - for backup or additional wired applicacations.

11. ReproScan 2.0 Monitor Indicator Lights and Battery Indicator
Baery Indicator
Battery Indicator
1. Indicator goes from 7 to 100.
2. It takes approximately 10 hours to charge from 7 to 100 (plug in over night).
3. The battery life is approximately 8 hours.
4. You many use while charging.
5. If the indicator does not reach a level of at least 97, call the ReproScan office as the battery
may need to be reset.
Page 9

12. Mounng your ReproScan 2.0 Monitor using Ram Mount® Parts
Recommended Ram Mount Kit—available from ReproScan
The following Ram Mount Parts have proven to be very useful for mounng
the ReproScan 2.0 monitor in almost all locaons.
Page 10
RAM - 111BU 6.25” length with 1.5” ball
(Type C ball = 1.5” diameter ball)
RAM - 201U medium length arm
RAM - 202U-225 1.5” ball on 2” 4 hole plate
For mounng on 6 1/2 foot long 2x4
RAM - 337U 1.5” ball with 1/4” x 20 thread
For mounng on Trigger Clamp
RAP - 401U RAM® Tough-Claw™
Large clamp with 1.5” ball
For mounng on tubular chutes