REYHEE Superlite User manual

1
User manual: Superlite
Before using your new REYHEE Superlite foldable electric wheelchair,
please read and comprehend ALL warnings, safety instructions, and
operational instructions as labeled on the product packaging box, on the
product itself, and in this user manual.
SKU number: XW-LY001-A
FDA-Cleared Class II Medical Device
www.reyhee.com

2
Table of contents
Table of contents............................................................................................................. 2
Introduction...................................................................................................................... 3
Packaging contents……………………………………………………………………………. 4
Getting to know your Superlite................................................................................... 5 - 6
Assembly.................................................................................................................. 7 - 19
Important battery/charger warnings and charging instructions............................... 19 - 23
Important warnings and safety instructions............................................................ 24 - 29
How to operate your Superlite................................................................................ 29 - 55
▪Pre-ride checklist……………………………………………………………..………. 29
▪How to unfold the Superlite………………………………………………..…… 30 - 33
▪How to lift and lower the armrests…………………………………………….. 34 - 35
▪How to use the dual rear levers……………………………………………….. 36 - 37
▪How to use the main controller…..………………………………………..…... 37 - 42
▪How to adjust the height of the rear handles………………………………… 42 - 43
▪How to use the rear handle controller………………………………………… 44 - 47
▪Getting in and sitting in the Superlite…………………………………………. 47 - 48
▪Standing up and getting out of the Superlite…………………………………. 48 - 49
▪How to fold the Superlite………………………………………………..……… 49 - 53
▪How to transport the Superlite……………………………………………..….. 53 - 55
Maintenance........................................................................................................... 56 - 57
Technical specifications………………………………………………………………… 58 - 59
Troubleshooting………………………………………………………………………………. 59
Warranty…………………………………………………………………………………. 60 - 61
Recycling and disposal…………………………………………………………………….…62
Customer support…………………………………………………………………………….. 62
DISCLAIMERS:
1) This product is NOT intended to be ridden or operated by children, pets, or persons with limited physical
and/or mental faculties.
2) All images and diagrams in the manual are for illustrative purposes only. They may not reflect the actual
appearance of the product or its components.
3) The appearance, specifications, and procedures of the product and any related accessories are subject to
change without notice. (The availability of related accessories is also subject to change without notice.)
Have an issue? Please don’t return this product. Our friendly customer support staff can help.
Call [phone], or email [e-mail]

3
Introduction
Reyhee offers mobility solutions that improve lives.
We’re not here to remind people that they’re dependent on a medical mobility device;
rather, we’re here to help people remember what it’s like to be mobile, be self-sufficient,
and most importantly, be independent.
Together, with Reyhee, people can continue to visit the places they hold fondly, remain
connected to the people they love, keep on doing that which they enjoy, and continue to
live—really live.
People need products from a brand they can trust, so we commit our decades of
experience and expertise to the development and manufacturing of safe, reliable, and
FDA approved mobility solutions that can be used with confidence.
Because life happens, and sometimes events and changes create challenges for us to
overcome, Reyhee prides itself on being able to offer that bit of help we sometimes
need so that we may get back to doing those activities we cherish.
And along the way make the life we knew, the life we know.

4
Packaging contents
When opening the packaging box, turn the box on its side and gradually pull out
the contents. (If you anticipate having difficulty with this step, please DO NOT
ATTEMPT to unpack - to prevent potential injury to yourself & potential damage to the
product - and seek assistance.)
The Superlite comes with the following items in the packaging box.
Please identify and locate all of the following prior to assembly:
1) Superlite foldable electric wheelchair
a) Pre-assembled frame, seat, and wheels (motors integrated in rear wheels)
b) Pre-installed power cables (x 2)
c) Pre-installed storage bag beneath the seat, with the following components inside:
•Pre-installed control box
•Pre-installed lithium-ion battery pack
•Pre-installed battery cable (must be connected by user –see assembly
instructions)
d) Pre-installed side storage bag (non-removable)
2) Charger with charging cable
3) Main controller (must be installed by user)
a) Integrated joystick and control buttons
b) Integrated charging port, USB port, and headlight (all located underneath)
c) Integrated controller cable
4) Rear handle controller (must be installed by user)
a) Integrated thumb joystick, power button, and controller cable
b) Screwdriver for installation (see assembly instructions)
5) User manual
Superlite wheelchair Charger with charging cable Main controller Rear handle controller

5
Getting to know your Superlite
Parts diagram: Side view

6
Getting to know your Superlite (cont.)
Parts diagram: Back view

7
Assembly
IMPORTANT: Your Superlite comes folded and mostly pre-assembled. Please read,
comprehend, and follow ALL warnings and instructions below PRIOR to operating your
Superlite.
WARNINGS:
1) If you observe damage to any part of the product upon unpacking, please DO
NOT ATTEMPT to assemble it and contact customer support for further
instructions.
2) Assembly MUST be conducted by an adult, who is able to demonstrate the
physical and mental faculties required to understand the instructions and execute
proper assembly.
3) DO NOT ALLOW children or persons with limited physical and/or mental faculties
to conduct assembly, as there may be small parts, sharp edges / sharp points,
and packaging material that can present as hazardous.
4) Ensure proper disposal (and/or recycling, per local laws) of all interior packaging
material, so that they are OUT OF REACH from children, pets, and any persons
with limited physical/mental faculties.
5) It is recommended that you KEEP the original packaging box, in the event that
the product needs to be stored away.
If you are not certain that you are capable of fully understanding and safely executing
the assembly steps below, please do not attempt assembly and seek assistance.

8
Assembly (cont.)
1) Step one: Unfolding the Superlite
a) Ensure the Superlite is upright and resting on all four wheels on a flat, even, and
dry indoor floor surface.
The dual rear levers (on the rear wheels) should both be in “D” (“Drive”)
position, to prevent accidental movement during unfolding.
Also ensure there is ample room for unfolding the Superlite.
b) On the back of the Superlite, there is a folding latch. To enable the Superlite to
unfold, lift the folding latch until it is fully unlocked.
Ensure your fingers and other body parts are safely out of the way of any
parts that may be moving as the folding latch is being unlocked.

9
Assembly (cont.)
Step one: Unfolding the Superlite (cont.)
c) Grasp one of the armrests firmly with one hand.
d) At the same time, use the other hand to push down on the opposite edge of the
seat cushion.
Ensure your hands and feet are safely out of the way of any parts that
may be moving as the Superlite is being unfolded.
e) Ensure the Superlite seat is fully unfolded, before proceeding to step two of
assembly.

10
Assembly (cont.)
2) Step two: Installing the main controller
Instructions for installing the main controller in the right-side armrest:
a) Follow these instructions if you intend to operate the Superlite with your RIGHT
hand.
Do NOT press the power button on the main controller, to prevent turning
on the product and potentially causing accidental product movement
during assembly.
b) Identify the installation point (open hole) in front of the right-side armrest.
c) Ensure the controller installation knob (located beneath the armrest) is partially
loosened. (Turn left to loosen, if needed.)

11
Assembly (cont.)
Step two: Installing the main controller (cont.)
d) Install the main controller (with the joystick and control buttons facing upward) by
sliding the metal tube into the installation point, all the way to the end.
Do NOT yank or pull the controller in such a way that its connection to the
power cable may become damaged, loosened, or otherwise
compromised.
e) Secure the main controller into the armrest by continuously turning the controller
installation knob to the right until it is fully tightened.
Instructions for installing the main controller in the left-side armrest:
a) Follow these instructions if you intend to operate the Superlite with your LEFT
hand.
b) Identify the left-side armrest cap, and remove it to reveal the installation point.
(Then install the cap onto the installation point of the right-side armrest, to
prevent dust or debris from going inside.)
c) Fully remove the controller installation knob (located beneath the right-side
armrest) by continuously turning it to the left. Install it into the left-side armrest by
turning it to the right, into the knob hole beneath the armrest.
d) Undo the velcro strap that attaches the power cable to the right-side armrest.

12
Assembly (cont.)
Step two: Installing the main controller (cont.)
Instructions for installing the main controller in the left-side armrest (cont.):
e) Move the power cable behind the seat until it reaches the left-side armrest, and
safely secure the cable with the velcro strap.
Ensure that the power cable is NOT in the way of sitting down, or in the
way of any parts that may move while the Superlite is in motion.
Otherwise, there will be risk of damage to the power cable.
f) Install the main controller (with the joystick and control buttons facing upward) by
sliding the metal tube into the installation point, all the way to the end.
g) Secure the main controller by continuously turning the controller installation knob
continuously to the right until it is fully tightened.
3) Step three: Connect the main controller cable to the power cable
a) Ensure that your hands are completely DRY.
Wet hands may cause an electrical shock or fire hazard.
b) Locate the main controller.
Ensure the controller cable attached to it has no damage or exposed
wiring.

13
Assembly (cont.)
Step three: Connect the main controller cable to the power cable (cont.)
c) There are two power cables: one for the main controller, and the other for the
rear handle controller.
Locate the power cable for the main controller (which has a rubber cover and is
attached by velcro strap to the right-side armrest). Push back the cable head’s
rubber cover.
Ensure the power cable has no damage or exposed wiring.
d) Using the arrow indicators on each cable, line up the main controller cable’s inner
prongs with the power cable’s inner socket. Firmly push until the two cables are
FULLY connected.
If the main controller cable’s inner prongs are not properly aligned with
the power cable’s inner socket, forcing the connection may result in
damage to both.

14
Assembly (cont.)
Step three: Connect the main controller cable to the power cable (cont.)
e) Lock the connection in place by spinning the metal locking ring clockwise until it
is fully tightened.
f) Pull the power cable’s rubber cover over the connection.
g) Push the main controller cable’s rubber cover until it touches the other rubber
cover.
4) Step four: Installing the rear handle controller
a) Ensure that your hands are completely DRY.
Wet hands may cause an electrical shock or fire hazard.
b) Locate the rear handle controller.
Ensure the controller cable attached to it has no damage or exposed
wiring.

15
Assembly (cont.)
Step four: Installing the rear handle controller (cont.)
c) Locate the screwdriver (included in packaging box). Using the screwdriver,
remove the 2 pre-installed screws on the back of the rear handle controller.
d) Locate the metal controller base on the right rear handle of the Superlite.
e) Place the rear handle controller on top of the base, with the power button
towards the upper end.

16
Assembly (cont.)
Step four: Installing the rear handle controller (cont.)
f) Ensure the controller’s screw holes align with the base’s holes.
g) Using the screwdriver, secure the rear handle controller to the base by installing
each screw from the bottom of the base. Ensure each screw is fully tightened.
Gently shake the rear handle controller –there should be no looseness.
h) Locate the remaining unattached power cable.
Ensure the power cable has no damage or exposed wiring.
i) Using the arrow indicators on each cable, line up the rear handle controller
cable’s inner prongs with the power cable’s inner socket. Firmly push until the
two cables are FULLY connected.
If the controller cable’s inner prongs are not properly aligned with the
power cable’s inner socket, forcing the connection may result in damage
to both.

17
Assembly (cont.)
Step four: Installing the rear handle controller (cont.)
j) Lock the connection in place by spinning the metal locking ring clockwise until it
is fully tightened.
5) Step five: Connecting the battery cable in the storage bag
a) Locate the storage bag beneath the seat, and unzip until the bag is fully open.
b) Inside the storage bag, lift the inner flap until the battery cable is visible (the
cable’s connecting ends are yellow).
Before attempting any cable connection, first ensure there is no damage
or exposed wiring on any cables. If any damage or wire exposure is found,
DO NOT proceed with assembly and contact customer support for
assistance.

18
Assembly (cont.)
Step five: Connecting the battery cable in the storage bag (cont.)
c) Align both ends (yellow) of the battery cable. Firmly push until they are FULLY
connected.
If the battery cable ends are not properly aligned, forcing the connection
may result in injury and/or product damage.
d) Replace the inner flap back to its original position, ensuring that all cables are
fully covered and bundled towards the back of the storage bag.
To prevent product damage and risk of fire:
If placing personal items inside the storage bag, ensure they are NOT
placed against or on top of the cables, battery pack, control box, or any
other electronic parts that may be inside the storage bag.
(See “Important warnings and safety instructions” section for more
details.)
------------------- ASSEMBLY IS NOW COMPLETE-------------------

19
But wait! BEFORE you begin operating your Superlite, please read and
comprehend ALL warnings and instructions outlined hereafter.
If you are NOT certain that you are capable of fully understanding and
following ALL warnings and instructions, please DO NOT ATTEMPT to
operate the product and seek assistance.
WARNINGS FOR LITHIUM-ION BATTERY PACK & CHARGER:
1) If there is evidence of DAMAGE, BREAKAGE, OR LEAKAGE on either the
battery pack (inside the storage bag) or charger, DO NOT USE OR ATTEMPT
TO FIX and contact customer support immediately.
2) TO AVOID FIRE OR EXPLOSION, DO NOT PLACE OR LEAVE battery pack or
charger near any heat or water sources (such as generators, gas / electric
heaters, water boilers, large appliances, lit cigarettes), or anything labeled
flammable, explosive, caustic, or volatile (such as gasoline, kerosene, propane).
3) TO AVOID ELECTRIC SHOCK OR POISONING, DO NOT ATTEMPT TO OPEN
the battery pack. It is sealed for your safety. Attempting to open it will also void
your warranty.
4) TO AVOID ELECTRIC SHOCK OR FIRE, DO NOT TOUCH the battery pack or
charger with wet hands or uninsulated metal.
5) TO AVOID ELECTRIC SHOCK, DO NOT submerge, soak, or wash the battery
pack or charger. THESE ACTIONS MAY CAUSE SHORT CIRCUITING OR
PERMANENT DAMAGE.
6) The product has a built-in overcurrent protection system, which will trigger an
AUTOMATIC SHUT-DOWN of the battery and motor if the current exceeds the
programmed limit. This helps to protect the components from potential damage.

20
Charging Instructions
If you observe any damage, bulging, or wire exposure on the charger or charging
cable, DO NOT USE or ATTEMPT TO FIX. Contact customer support for assistance.
1) Ensure that your hands are completely DRY.
Wet hands may cause an electrical shock or fire hazard.
2) To charge the product:
a. First ensure the product is powered OFF. (If either controller is on, press
the power button on the controller to turn the product off.)
b. Locate the charger and charging cable.
c. Connect the charging cable to the charger.
d. Locate the charging port (beneath the main controller).