RH Baby&child BENNET User manual

11
/
1/15

IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions
could result in serious injury or death.
·To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on their backs to
sleep, unless otherwise approved by your physician.
Strangulation Hazard:
·Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
·To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
·DO NOT place a crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
·When a child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
·When a child is able to climb out or reaches the height of 35" (89cm), the crib should no longer be
used, and the child should be placed in a youth or regular bed.
·Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT
use crib if any parts are missing, damaged or broken. Contact customer service at 1-800-762-1751
for replacement parts and instructional literature if needed.
·DO NOT substitute parts.
·DO NOT use a water mattress with this crib.
·If refinishing, use a non-toxic finish specified for children’s products.
·Follow warnings on all products in a crib.
·Never use plastic shopping bags or other plastic film as mattress covers because they can cause
suffocation.
·Infants can suffocate in gaps between crib sides and a mattress that is too small.
2/15

IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB SHOULD BE
AT LEAST 27 1/4" X 51 5/8" WITH A THICKNESS
NOT EXCEEDING 6".
WARNING
Do not use this crib if you cannot exactly follow the instructions
provided.
Do not use this crib for a child who can climb out of it or who is
taller than 35" (89cm).
Do not place in or near the crib any cord, strap or similar item that
could become wrapped around a child's neck.
Do not place this crib near a window or patio door where a child
could reach the cord of a blind or curtain and get strangled.
Check this crib regularly before using it, and do not use if any part
is loose or missing or if there are any signs of damage.
Do not substitute parts. Contact the manufacturer if replacement
parts or additional instructions are needed.
Children can suffocate on soft bedding. Do not place pillows,
comforters or soft mattresses in this crib.
Use a mattress that is no thicker than 15cm in height, and when
pushed firmly against any side of the crib, there should not be a
gap of more than 3cm between the mattress and any part of any
other side of the crib.
3/15

IMPORTANT SAFETY INFORMATION FOR TODDLER AND DAYBEDS
·The mattress intended for use on the bed is a full-size crib mattress
having minimum dimensions of 51 5/8" (1310mm) in length, 27 1/4"
(690mm) in width and 4" (100mm) in thickness, not exceeding 6"
(150mm) in thickness.
·DO NOT place bed near windows where cords from blinds or
drapes may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or daybed should be at least 15 months of
age and not weigh more than 50lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months of age.
DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
4/15

ITEM IDENTIFICATION
For ease of identification, all parts are labeled to correspond
to the step number in which the part is used.
Step 1 Fully remove the drawers and bottom panel of the storage
Side rail panels and storage assembly (Page 6)
Step 2 Install the bottom panel and drawers (Page 7)
Step 3 Mattress support assembly (Page 8)
Step 4 Headboard assembly (Page 9)
Step 5 Front rail assembly and hiding unused holes (Page 10)
Step 6 Toddler rail assembly (Page 11)
Step 7 Metal bed frame assembly (Page 12)
Step 8 Drawer removal instructions (Page 13)
Step 9 Drawer assembly instructions (Page 14)
Step 10 Drawer height adjustment instructions (Page 15)
5/15
DECORATIVE
WOOD CAPS
STORAGE
HEADBOARD
SIDE RAIL PANEL
(RIGHT)
SIDE RAIL PANEL
(LEFT)
TODDLER RAIL
(SOLD SEPRATELY)
MATTRESS
SUPPORT
FRONT RAIL

6/15
STEP 1
FULLY REMOVE THE DRAWERS AND BOTTOM PANEL OF THE STORAGE
SIDE PANELS AND STORAGE ASSEMBLY
STEP 1.1
Fully remove all the drawers out of the storage.
Please see detail on page 13 to remove drawer.
See DETAIL A.
STEP 1.2
Unscrew all screws on the bottom panel and fully
remove the bottom panel from storage. See
DETAIL B.
STEP 1.3
Align the locator pins on the end of the storage to
the corresponding holes in the side rail panel (left),
insert the side rail panel into the storage.
STEP 1.4
Attach the side rail panel to the storage by using
Allen bolts (CC) with the lock washers and plain
washers. See DETAIL C.
STEP 1.5
Repeat above procedure to attach the side rail
panel (right) to the storage.
HARDWARE NEEDED FOR STEP 1
(CC) 1/4" x 1 3/8" Allen Bolt = 8 pcs
Lock Washers = 8 pcs
Plain Washers = 8 pcs
Allen Wrench = 1 pc
B
DETAIL B
DETAIL A
DETAIL C
C
(AA)

7/15
STEP 2
INSTALL THE BOTTOM PANEL AND DRAWERS
STEP 2.1
Install the bottom panel. See DETAIL D.
STEP 2.2
Once the stabilizer rails are set, gently
tilt the crib as illustrated in DETAIL E.
STEP 1.3
Return the drawers to the storage by
following the instructions on pages 14
and 15. See DETAIL F.
D
DETAIL D
DETAIL E
DETAIL F

8/15
STEP 3
MATTRESS SUPPORT ASSEMBLY
STEP 3.1
Attach the support arms to the mattress support, using Allen bolts
(BB) with lock washers and plain washers. See DETAIL G.
STEP 3.2
Hang the mattress support on both end panels by using Allen bolts
(BB), lock washers and plain washers, as per illustration in DETAIL H.
WARNING:
Set the mattress support to the desired height by adjusting the
support arms. The mattress support should be at its highest setting
for newborns, then adjusted to the lower positions as the child grows
and becomes mobile. Once the child is able to stand, the mattress
support should be at its lowest position.
HARDWARE NEEDED FOR STEP 3
(BB) 1/4" x 13/16" Allen Bolt = 8 pcs
Lock Washer = 8 pcs
Plain Washer = 8 pcs
Allen Wrench = 1 pc
Support Arm = 4 pcs
G
H
G
G
G
H
(BB)
(BB)
DETAIL G
DETAIL H

STEP 4
HEADBOARD ASSEMBLY
9/15
STEP 4.1
Insert the headboard to the back sides of the side
panels.
STEP 4.2
Use Allen bolts (CC), lock washers and plain
washers to attach the crib headboard to the side
panels. Please see DETAIL I and DETAIL J.
HARDWARE NEEDED FOR STEP 4
(AA) 1/4" x 2 3/16" Allen Bolt = 4 pcs
Lock Washers = 4 pcs
Plain Washers = 4 pcs
Allen Wrench = 1 pc
I
J
(AA)
(AA)
DETAIL I
DETAIL J
Not used

10/15
(AA)
DETAIL K
DETAIL L
(DD)
HARDWARE NEEDED FOR STEP 5
(AA) 1/4" x 2 3/16" Allen Bolt = 4 pcs
Lock Washers = 4 pcs
Plain Washers = 4 pcs
Allen Wrench = 1 pc
(DD) 1/4" x 1/2" Allen Bolt = 8 pcs
STEP 5
FRONT RAIL ASSEMBLY AND HIDING UNUSED HOLES
STEP 5.1
Both ends of the front rail have holes for the bolts to pass through
that correspond to the holes on the posts for both side rail panels
with pre-installed nuts. Attach the front rail frame to the side rail
panels by using Allen bolts (AA) with lock washers and plain
washers. See DETAIL K.
After assembly, re-tighten all bolts for a snug fit. DO NOT
OVERTIGHTEN.
STEP 5.2
When the mattress support is in the middle or lowest setting,
unused holes can hurt your child's fingers. Please use Allen bolts
(DD) provided to hide these holes. See illustration in DETAIL L.
L
K

11/15
STEP 6
TODDLER RAIL ASSEMBLY
STEP 6.1
Loosen all the bolts on both ends of the front side
rail to disassemble the front side rail.
STEP 6.2
Replace the front side rail by the toddler rail. See
DETAIL M.
After assembly, re-tighten all bolts to a snug fit.
DO NOT OVER TIGHTEN.
STEP 6.3
Visible unused holes can hurt your child's finger.
Please use Allen bolts (EE) provided (Packed
inside toddler rail box) to hide these holes. See
illustration in DETAIL N.
Allen Wrench = 1 pc
(EE) 1/4" x 1/2" Allen Bolt = 2 pcs
HARDWARE FOR STEP 6
(PACKED INSIDE TODDLER RAIL BOX)
DETAIL M
DETAIL N
(EE)
(CC)
M
N
M

DETAIL O
12/15
STEP 7
METAL BED FRAME ASSEMBLY
DETAIL P
O
P
(FF)
STEP 7.1
Loosen all the bolts on the crib to disassemble
the crib.
STEP 7.2
Bring the headboard to the upright position.
STEP 7.3
At the bottom of the headboard there are holes
for the bolts to pass through that correspond to
the holes on the metal bed frame. Attach the
metal bed frame to the headboard by using
Allen bolts (FF) with lock washers and plain
washers into the sleeve nut on the other side.
See DETAIL O.
STEP 7.4
Fill the holes located on the top of the side rail panel
by attaching the decorative wood caps with Allen
bolts (AA). See DETAIL P .
HARDWARE NEEDED FOR STEP 7
(FF) M6 x 50mm Allen Bolt = 4 pcs
Lock Washers = 4 pcs
Plain Washers = 4 pcs
Allen Wrench = 2 pcs
Sleeve Nut M6 = 4 pcs
Allen Wrench = 1 pc
(AA) 1/4" x 2-3/16" Allen Bolt = 2 pcs
Lock Washers = 2 pcs
Plain Washers = 2 pcs
(AA)
DETAIL P

13/15
STEP 8
DRAWER REMOVAL INSTRUCTIONS
STEP 8.1
Pull the drawer out. See at bottom side of drawer. Unlock the plastic
peg by pulling black plastic peg on runner out. See DETAIL Q.
STEP 8.2
Hold the drawer with both hands. Carefully lift the drawer front up
from the front metal pin, then slide drawer forward to remove from
back hooks. See DETAIL R.
UNLOCK
Plastic peg
Metal pin/
Hole for pin
DETAIL Q
DETAIL R

LOCK
14/15
STEP 9
DRAWER ASSEMBLY INSTRUCTIONS
STEP 9.1
Pull the runner on the way out. Put
the drawer onto them, then hold both
the runner with your hands. Lift the
drawer up with your thumbs and push
to hook the drawer at end of the
runner. See DETAIL S.
STEP 9.2
Hold the drawer with both hands.
Carefully lift the drawer front up from
the front metal pin, then slide forward
to remove from back hooks. See
DETAIL T.
STEP 9.3
Lock the drawer to the runner by
pushing the black plastic peg on the
runner in. See DETAIL U.
Metal pin/
Hole for pin
DETAIL S
Metal hook
DETAIL T
DETAIL U

15/15
STEP 10
DRAWER HEIGHT ADJUSTMENT INSTRUCTIONS
Adjust around gap of drawer by turning
plastic button clockwise/counterclockwise
direction. See DETAIL V.
Plastic button
DETAIL V