RH Baby&child DRAKE F0035 - 6 User manual

Page 1 of 12
TODDLER BED CONVERSION KIT (SOLD SEPARATELY)
Made in Vietnam
Model No: F0035 - 6/7
Distributed in the U.S.A by:
RH Baby&Child
2900 N MACARTHUR DRIVE
TRACY, CA 95376
www.rhbabyandchild.com
Distributed in Canada by:
RH Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia
V6E4N7
WARNING: Read all
Instructions before assembling
this product.
KEEP INSTRUCTIONS FOR
FUTURE USE.
CUSTOMER SERVICE
If you are missing partsor have any questions about this product, contact us first. You can also order parts by writing to
the address above. Include the product model number, color, and a brief descriptionof the part.Or call 1-800-762-1751.
CARE AND CLEANING
TOOLS AND INSTALLATION
Tools needed: Key Wrench (included).
Two people are recommended for assembly.
When inserting bolts, turn clockwise until tight. Then loosen 1/2-3/4 of aturn. After bed is completely assembled,
return to each bolt and tighten.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning.If the crib is to be stored, store in a cool,
dry place and carefully package all original hardware to protect from loss.
1. Read all instructions before assembly crib. Keep instructions for future use.
2. Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
3. Infants can suffocate in gaps between crib sides and a mattress that is too small.
DRAKE UPHOLSTERED CRIB

Page 2 of 12
Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless
otherwise advised by your physician.
Strangulation Hazard:
Strings can cause strangulation! DO NOT place items with a string around a child's neck, such as hood strings or
pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
Fall Hazard:
When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads, large
toys and other objects that could serve as steps for climbing out.
When child is able to climb out or reaches the height of 35 inches (89 cm), the crib shall no longer be used, and
the child should be placed in a youth or regular bed.
Check this product for damaged hardware, loose joints, missing parts or sharp edges before and after assembly
and frequently during use. DO NOT use crib if any parts are missing, damaged or broken.
Contact customer service at 1-800-762-1751 for replacement parts and instructional literature if needed.
DO NOT substitute parts.
DO NOT use a water mattress with this crib.
If refinishing, use a non-toxic finish specified for children's products.
Follow warnings on all products in a crib.
Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
Infants can suffocate in gaps between crib sides and a mattress that is too small.
WARNING: Infants can suffocate on soft bedding. Never add a pillow or comforter. Never
place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions could result
in serious injury or death.
DRAKE UPHOLSTERED CRIB

Page 3 of 12
CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27 1/4
INCHES BY 51 5/8 INCHES WITH A THICKNESS NOT EXCEEDING
6 INCHES.
WARNING:
Do not use this crib if the enclosed or attached instructions cannot
be strictly adhered to. Do not use this crib if the child is able to climb
out unaided or is taller than 35 inches (890mm). Do not place
cords, straps or similar items that could become wound around the
child's neck in or near this crib. Ensure that the sides are properly
latched or locked in place when the crib is occupied. The mattress
used with this crib should not be more than 5 7/8 inches (150mm)
thick and should be of such length and width that the gap between
the mattress and the sides of the crib is not more than 1 3/16 inches
(30mm) when the mattress is pushed into the corner of the crib.
Parents should inspect the crib regularly before putting the child
in the crib each day and confirm that every component of the crib
is properly and securely in place.
DRAKE UPHOLSTERED CRIB

Page 4 of 12
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.
The mattress intended for use on the bed shall be a full-size crib mattress
having minimum dimensions of 51 5/8 inches (1310mm) in length, 27 1/4
inches (690mm) in width and 4 inches (100mm) in thickness, not
exceeding 6 inches (152mm) in thickness.
If guardrails are used as the mattress containment means, the guardrail(s)
provided must be used to avoid the formation of a gap between the
mattress and the bed that could cause an entrapment.
DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
DO NOT place items with a string, cord, or ribbon around a child's neck,
such as hood strings or pacifier cords.
A child using the toddler or day bed shall be at least 15 months of age
and shall not weigh more than 50lbs (22.7kg).
WARNING: ENTRAPMENT/ STRANGULATION HAZARD
DRAKE UPHOLSTERED CRIB

Page 5 of 12
PARTS INCLUDED:
A
B
C
HARDWARE INCLUDED:
[2]
[2]
[1]
HEADBOARD/ FOOTBOARD
STATIONARY SIDE RAIL
MATTRESS SUPPORT
A
A
B
B
C
1
2
3
4
5
Long Bolts 5/16”x 2”8 pcs.
Spring Washer 5/16”
Insert Head 6mm
L Pin 6mm
8 pcs.
4 pcs.
4 pcs.
NO. ITEM DESCRIPTIONQTY.
Allen Key 4mm 1 pc.
DRAKE UPHOLSTERED CRIB

Attach the Stationary Side Rail (B) to the
Headboard/ Footboard (A) with Long Bolt (1),
Spring Washer (2), and tighten using Allen
Key (5).
DO NOT FULLY TIGHTEN AT THIS TIME !.
Page 6 of 12
STEP 1:
STEP 2
:
A
A
4x
A
A
A
B
B
1
5
44x
2
Insert L Pi n (4) into the holes on the Headboard/
Footboard (A).
Note: The Mattress supp ort ( C) should be at th e
highest level when the childis born.
It must be at the lowest leve l b e fore the child can
stand up. Befo re installing the Mattress support (C),
please ask the custo m er at which height they want
it installed.
A
Highest level
Lowestlevel
Middle level
DRAKE UPHOLSTERED CRIB

Page 7 of 12
STEP 3:
STEP 4:
A
A
C
C
Attach the Mattress Support (C) with Insert
Head (3), L Pin (4), and tighten by using
Allen Key (5).
4x
4
3
4
5
A
4x
A
A
A
Position the Masstres support (C) between
the Headboard/Footboard (A). Then align
L Pin (4) into the pre-drilled holes of the
Mattress Support (C).
C
C
Top
Bottom
DRAKE UPHOLSTERED CRIB

Page 8 of 12
STEP 6:
A
B
Attach the Stationary Side Rail (B) to the
Headboard/Footboard (A) with Long Bolt (1),
Spring Washer (2), and tighten using Allen
Key (5).
After crib is completely assembled, return to each
bolt and tighten to snug fit. DO NOT over tighten.
1
5
2
4x
WARNING:
Position the Stationary Side rail (B) between
the Headboard/Footboard (A) and align the
holes.
STEP 5:
A
A
A
B
DRAKE UPHOLSTERED CRIB

Page 9 of 12
PARTS INCLUDED:
D
HARDWARE INCLUDED:
[1] TODDLER RAIL
D
6
7
8
9
Long Bolts 5/16”x 2”
Small Bolts 5/16”x 3/4”
4 pcs.
Spring Washer 5/16”
2 pcs.
6 pcs.
NO. ITEM DESCRIPTIONQTY.
Allen Key 4mm 1 pc.
DRAKE UPHOLSTERED CRIB

Remove Stationary Side Rail (B) from the
crib by carefully unscrewing and removing
the [4] Long bolts (1) with spring washer
on Left/Right sides of the Stationary Side
Rail (B) using Allen Key (9).
Page 10 of 12
STEP 7:
If mattress support is not in the lowest
position, loosen all tightened bolts from
side frames. Spread front of crib open
enough to remove mattress support (C),
and move it to the lowest position.
STEP 8:
A
4x
B
A
Highest
level
Note: The Mattress support (C) must be at
the lowest level for a toddler bed.
Middle
level
Lowest
level
C
9
A
A
B
C
B
1
9
2
4x
DRAKE UPHOLSTERED CRIB

Page 11 of 12
STEP 9:
Position the Toddler Rail (D) between the
Headboard/Footboard (A) and align the holes.
Attach the Toddler Rail (D) to the crib
by securing with Long Bolts (6), Spring
Washers (8), and tighten with Allen
Key (9).
STEP 10:
A
D
D
A
6
8
A
D
9
4x
DRAKE UPHOLSTERED CRIB

Page 12 of 12
STEP 11:
When converting the crib to toddler bed, the
Small Bolt (7), and Spring Washer (8) should
be inserted in the upper holes of the Side
Frame (A) and tighten with the Allen Key (9).
A
A
A
2x
89
7
CARE INSTRUCTIONS
Dust often using a clean, soft, dry lint-free cloth.
Blot spills immediately, and wipe with a clean, damp cloth.
Do not use chemical cleaners, abrasives or furniture polish on the lacquered finish.
After crib is completely assembled, return
to each bolt and tighten to snug fit.
DO NOT over tighten.
WARNING:
DRAKE UPHOLSTERED CRIB