RH Baby&child MADERO User manual

MADERO STORAGE CRIB - ASSEMBLY INSTRUCTIONS
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
Made in Vietnam
Distributed in the USA by:
RH Baby&Child
2900 North Macarthur Dr.
Tracy, CA 95376
USA
www.rhbabyandchild.com
Distributed in Canada by:
RH Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the address above.
Include the product model number, color, and a brief description of the part. Or call 1-800-762-1005.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth.
Blot spills immediately and wipe with a clean, damp cloth. If the crib is to be stored, store in a cool, dry place and carefully package all original
hardware to protect from loss.
TOOLS NEEDED
Allen Wrench (included)
NOTE: Two people are recommended for assembly.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12 - 34 of a turn. After crib is completely assembled, return to each bolt and
tighten. Use wax or soap on all bolts to facilitate assembly.
1/14

2/14
IMPORTANT SAFETY INFORMATION FOR CRIBS
WARNING: Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
WARNING: Failure to follow these warnings and the assembly instructions
could result in serious injury or death.
·To reduce the risk of SIDS, pediatricians recommend healthy infants to be placed on their backs to
sleep, unless otherwise approved by your physician.
Strangulation Hazard:
·Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
·To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on
loose fasteners.
·DO NOT place crib near a window where cords from blinds or drapes may strangle a child.
Fall Hazard:
·When a child is able to pull to a standing position, set mattress to lowest position and remove
bumper pads, large toys and other objects that could serve as steps for climbing out.
·When a child is able to climb out or reaches the height of 35" (89cm), the crib should no longer be
used, and the child should be placed in a youth or regular bed.
·Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT
use crib if any parts are missing, damaged or broken. Contact customer service at 1-800-762-1005
for replacement parts and instructional literature if needed.
·DO NOT substitute parts.
·DO NOT use a water mattress with this crib.
·If refinishing, use a non-toxic finish specified for children’s products.
·Follow warnings on all products in a crib.
·Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
·Infants can suffocate in gaps between crib sides and a mattress that is too small.

3/14
IMPORTANT SAFETY INFORMATION FOR CRIBS
CAUTION: ANY MATTRESS USED IN THIS CRIB SHOULD BE
AT LEAST 27 1/4" X 51 5/8" WITH A THICKNESS
NOT EXCEEDING 6".
WARNING
Do not use this crib if you cannot follow the instructions exactly as
provided.
Do not use this crib for a child who can climb out of it or who is
taller than 35" (89cm).
Do not place in or near the crib any cord, strap or similar item that
could become wrapped around a child's neck.
Do not place this crib near a window or patio door where a child
could reach the cord of a blind or curtain and get strangled.
Check this crib regularly before using it, and do not use if any part
is loose or missing or if there are any signs of damage.
Do not substitute parts. Contact the manufacturer if replacement
parts or additional instructions are needed.
Children can suffocate on soft bedding. Do not place pillows,
comforters or soft mattresses in this crib.
Use a mattress that is no thicker than 15cm in height, and when
pushed firmly against any side of the crib, there should not be a
gap of more than 3cm between the mattress and any part of any
other side of the crib.

4/14
IMPORTANT SAFETY INFORMATION
FOR TODDLER BEDS AND DAYBEDS
·The mattress intended for use on the bed is a full-size crib mattress
having minimum dimensions of 51 5/8" (1310mm) in length, 27 1/4"
(690mm) in width and 4" (100mm) in thickness, not exceeding 6"
(150mm) in thickness.
·DO NOT place bed near windows where cords from blinds or
drapes may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler bed or daybed should be at least 15
months of age and not weigh more than 50 lbs (22.7 kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use a toddler bed or daybed with children under 15 months
of age.
DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.

ITEM IDENTIFICATION
For ease of identification, all parts are labeled to correspond
to the step number in which the part is used.
Step 1 Fully remove the drawers and dust panel of the storage
End panels and storage assembly (Page 6)
Step 2 Install the dust panel and drawers (Page 7)
Step 3 Mattress support assembly (Page 8)
Step 4 Side rails assembly (Page 9)
Step 5 Hide unused holes (Page 10)
Step 6 Toddler rail assembly (Page 11)
Step 7 Drawer removal instructions (Page 12)
Step 8 Drawer assembly instructions (Page 13)
Step 9 Drawer height adjustment instructions (Page 14)
5/14
END PANEL
END PANEL
Do not remove protective
foam tubes until crib is
fully assembled.
SIDE RAIL
MATTRESS
SUPPORT
STORAGE
TODDLER RAIL
(SOLD SEPRATELY)

6/14
STEP 1
FULLY REMOVE THE DRAWERS AND DUST PANEL OF THE STORAGE
END PANELS AND STORAGE ASSEMBLY
STEP 1.1
Fully remove all the drawers out of the storage. Please
see detail on page 12 to remove drawers. See DETAIL
A.
STEP 1.2
Loosen all bolts on the dust panel and fully remove the
dust panel from storage. See DETAIL B.
STEP 1.3
Align the locator pins on the end of the storage to the
corresponding holes in the end panel. Insert the end
panel into the storage.
STEP 1.4
Attach the end panel to the storage by using Allen bolts
with the lock washers and plain washers. See DETAIL C.
STEP 1.5
Repeat above procedure to attach the other end panel to
the storage.
DETAIL A
B
DETAIL B
HARDWARE NEEDED FOR STEP 1
(CC) 14" x 1" Allen Bolt = 8 pcs
Lock Washers (Ø10 x Ø6.5 x 1.5mm) = 8 pcs
Plain Washers (Ø12 x Ø6.5 x 1.5mm)= 8 pcs
C
Allen Wrench (57 x 23 x D4mm) = 1 pc
DETAIL C
(CC)

7/14
STEP 2
INSTALL THE DUST PANEL AND DRAWERS
STEP 2.1
Install the bottom panel on the back bottom of
the crib. See DETAIL D.
STEP 2.2
Once the stabilizer rails are set, gently tilt the
crib up as illustrated in DETAIL E.
STEP 1.3
Return the drawers to the storage by following
step on pages 13 and 14. See DETAIL F.
D
DETAIL E
DETAIL D
DETAIL F

8/14
STEP 3
MATTRESS SUPPORT ASSEMBLY
STEP 3.1
Insert the L-shaped pins into the end panels. See DETAIL G.
STEP 3.2
Place the mattress support on the L-shaped pins, making
sure the threaded ends go through the holes on the mattress
support, as shown DETAIL H.
WARNING:
Set the mattress support to the desired height by adjusting
the L-shaped pins. The mattress support should be at its
highest setting for newborns, then adjusted to the lower
positions as the child grows and becomes mobile. Once the
child is able to stand, the mattress support should be at its
lowest position.
HARDWARE NEEDED FOR STEP 3
G
DETAIL G
L-shaped pin 14" (47 x 38 x Ø8mm) = 4 pcs
Female Allen Bolt 1/4" (Ø15 x Ø9 x 16mm) = 4 pcs
Allen Wrench (57 x 23 x D4mm) = 1 pc
H
DETAIL H

9/14
STEP 4
SIDE RAILS ASSEMBLY
On both ends of the side rail are holes for the bolts
to pass through, which correspond to the holes on
the posts for both end panels with pre-installed
nuts. Attach the side rail to the end panels by
using Allen bolts (AA) with lock washers and plain
washers. See DETAIL I.
After assembly, re-tighten all bolts for a snug fit.
DO NOT OVERTIGHTEN.
Then, fully remove all protective foam tubes on the
both of the side rails before use.
HARDWARE NEEDED FOR STEP 4
(AA) 1/4" x 1-3/4" Allen Bolt = 8 pcs
Lock Washers (Ø10 x Ø6.5 x 1.5mm) = 8 pcs
Plain Washers (Ø12 x Ø6.5 x 1.5mm) = 8 pcs
(AA)
DETAIL I
Allen Wrench (57 x 23 x D4mm) = 1 pc
Fully remove the protective foam tubes before use

10/14
STEP 5
HIDE UNUSED HOLES
When the mattress support is in middle or lowest setting,
unused holes can hurt your child's fingers. Use Allen bolts (BB)
provided to hide these holes. See illustration in DETAIL J.
HARDWARE NEEDED FOR STEP 5
(BB) 1/4" x 1-3/8" Allen Bolt = 8 pcs
Allen Wrench (57 x 23 x D4mm) = 1 pc
(BB)
DETAIL J

11/14
STEP 6
TODDLER RAIL ASSEMBLY
STEP 6.1
Loosen all the bolts in both ends of the front side
rail to disassemble the front side rail.
STEP 6.2
Replace the front side rail with the toddler rail.
See DETAIL K.
After assembly, re-tighten all bolts to a snug fit.
DO NOT OVERTIGHTEN.
STEP 6.3
Some visible unused holes can hurt your child's
finger. Please use Allen bolts (EE) provided
(packed inside toddler rail box) to hide these
holes. See illustration in DETAIL L.
(EE) 1/4" x 1/2" Allen Bolt = 2 pcs
HARDWARE FOR STEP 6
(PACKED INSIDE TODDLER RAIL BOX)
DETAIL K
DETAIL L
Allen Wrench (57 x 23 x D4mm) = 1 pc
L
LK
K
(EE)

12/14
STEP 7
DRAWER REMOVAL INSTRUCTIONS
STEP 7.1
Pull the drawer out. See at bottom side of drawer. Unlock the plastic
peg by pulling black plastic peg on runner out. See DETAIL M.
STEP 7.2
Hold the drawer with both your hands. Carefully lift the drawer front
up from the front metal pin, then slide drawer forward to remove from
back hooks. See DETAIL N.
UNLOCK
Plastic peg
Metal pin/
Hole for pin
DETAIL M
DETAIL N

LOCK
13/14
STEP 8
DRAWER ASSEMBLY INSTRUCTIONS
STEP 8.1
Pull the runners all the way out. Put
the drawer onto them, then hold both
the runners with your hands. Lift the
drawer up with your thumbs and push
to hook the drawer at end of the
runner. See DETAIL O.
STEP 8.2
Hold the drawer with both of your
hands. Carefully lift the drawer front
up from the front metal pin, then slide
forward to remove from back hooks.
See DETAIL P.
STEP 8.3
Lock the drawer to the runner by
pushing the black plastic peg on the
runner in. See DETAIL Q.
Metal pin/
Hole for pin
DETAIL O
Metal hook
DETAIL P
DETAIL Q

14/14
STEP 9
DRAWER HEIGHT ADJUSTMENT INSTRUCTIONS
Adjust around gap of drawer by turning plastic button
clockwise/counterclockwise. See DETAIL R.
Plastic button
DETAIL R