RHINO PLAY M01474W User manual

1
© 2011 Escalade Sports For Customer Service Call 1-888-996-2729
Or writeto:
EscaladeSports
CustomerServiceDepartment
P.O.Box889
Evansville IN 47706
We strive to ensure that our products are of the highest quality
and free of manufacturing defects or missing parts. However, if
you have any problems with your new product,
DO NOT RETURN IT TO THE STORE,
please contact us toll free @:
WhencontactingEscalade Sportspleaseprovideyourmodelnumber, datecode(if
applicable),andpartnumber if requestingareplacementpart.Thesenumbersare
located on theproduct,packaging,andinthisownersmanual.
YourModelNumber__________________________
M01474W
Please have your date code when inquiring about parts.
1-888-996-2729
FAX: [phone]
[email protected]m
DateCode__________________________________
2 - M01474W - - WJ
Purchase Date______________________________
All Rights Reserved

2 For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
All Rights Reserved
IMPORTANT! READ EACH STEP
IN THIS MANUAL BEFORE YOU
BEGIN THE ASSEMBLY.
TWO (2) ADULTS ARE REQUIRED TO ASSEMBLE
THIS RHINO DOUBLE SHOOTOUT
READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO
ADULTS ARE NEEDED TO PUT THIS PRODUCT
TOGETHER.
Tools Needed:
Allen Wrench T1 & Wrench T2 and T3 (Included with the Hardware Kit)
Philips Screwdriver
Adjustable Wrench or Socket Set is helpful but not required.
A Small step ladder
Make sure you understand the following tips before you begin to assemble your
double shootout.
1.This is an electrically operated product.It is intended for INDOOR use ONLY.
2.This product is not designed to be used in a garage or on a patio,sunlight may effect
the infrared sensors and the unit will not perform correctly.
You may need to move the unit if it does not perform correctly.
3.Tighten hardware as instructed.
4.Do not over tighten hardware,as you could crush the tubing.
5.Some drawings or images in this manual may not look exactly like your product.
6.To prevent damage to the electronics do not place this unit any closer that six
inches from the wall.
!

3For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
All Rights Reserved
(To Scale)
HARDWARE IDENTIFIER
H1 - 5/16” x 1”
Allen Head Bolt (14)
H8 - 4mm x 10mm
Philips Round
Head Screw (16)
H5 - 1/4” x 1”
Allen Head Bolt (12)
H11 - 1/4” x 1-1/8”
Allen Head Bolt (10)
H6 - 1/4” x 7/8”
Allen Head Bolt (12)
H16 - 1/4”
Lock Washer (8)
H4 - 5/16” x 19mm
Flat Washer (14)
H18 - 4mm
Lock Nut (4)
H3 - 1/4”
Lock Nut (12)
H2 - 1/4” x 1-3/4”
Allen Head Bolt (4)
H9 - 4mm x 1-3/4”
Philips Washer Round
Head Screw (12)
H17 - 4mm x 20mm
Philips Round
Head Bolt (4)
H7 - 1/4” x 15mm
Flat Washer (34)
H12 - 4mm x 12mm
Philips Round
Head Screw (24)
H15 - 4mm x 1-3/4”
Philips Flat
Head Screw (16)
H13 - 4mm x 18mm
Philips Round
Head Screw (4)
T2 - 1/4” Wrench (1)
T3 - 4mm Wrench (1)
H14 - Metal
Connector (6)
(Not to Scale)
(Not to Scale)
T1 - Allen Wrench (1)
H10 - 4mm x 8mm
Philips Round
Head Bolt (8)
(Not to Scale)
!
WARNING:
CHOKING HAZARD
Small parts.
Not for children under 3 yrs.
(Not to Scale)
ACCESSORY IDENTIFIER
A1 - Basketball (4) A2 - Air Pump with Needle (1) A3 - AC Adapter (1)

4For Customer Service Call 1-888-996-2729
© 2011 Escalade Sports
All Rights Reserved
P8 - Leg Connecting
Panel (4)
P6 - Front Leg Panel (1) P7 - Back Leg Panel (2)
NOTE:
SWAGE
P10 - Back Side Ramp
Support Tube (2)
P11 - Front Side Ramp
Support Tube (2)
P15 - Side Net Pole
Support (2)
P16 - Plastic Bracket (2) P17 - Rim (2)
P20 - Rim Net (2)
P18 - Rim Support
Plate (2)
P22L - Left
Stiffener Board (2)
P12 - 45” Front
Ramp Support
Round Tube (1)
P19 - Electronic Scoreboard
with Sensors (1)
(Not to Scale)
PARTS IDENTIFIER
P9 - Backboard (1)
P13 - 45.5” Back
Ramp Support
Round Tube (1)
P14 - 45.875” Back
Ramp Support
Round Tube (1)
P21 - Ramp Net (1)
P22R - Right
Stiffener Board (2)
NOTE:
PRE-DRILLED
HOLES
NOTE:
TWO PRE-DRILLED
HOLES
P3L - Left Back
Bottom Leg (1)
P1R - Right
Front Leg (1)
P1L - Left
Front Leg (1)
P5L - Left Back
Top Leg (1)
P2 - Front Top Apron (1)
P4 - Side Back
Top Leg (2)
P3R - Right Back
Bottom Leg (1)
P5R - Right Back
Top Leg (1)

STEP 1:
Attach two Back Leg Panels P7 between
Left Back Bottom Leg P3L and Right Back
Bottom Leg P3R using Allen Head Bolts H5
with Flat Washer H7 as shown in FIGURE 1.
5
© 2011 Escalade Sports For Customer Service Call 1-888-996-2729
PARTS REQUIRED:
8 pcs - H5 Allen Head Bolt
8 pcs - H7 Flat Washer
1 pc - P3L Left Back Bottom Leg
1 pc - P3R Right Back Bottom Leg
2 pcs - P7 Back Leg Panel
1 pc - T1 Allen Wrench
FIGURE 1
H5 H7
P7
P7
P3R
P3L
H5 H7
H5 H7
PARTS REQUIRED:
2 pcs - H6 Allen Head Bolt 4 pcs - H13 Philips Round Head Screw 1 pc - P6 Front Leg Panel
2 pcs - H7 Flat Washer 1 pc - P1R Right Front Leg 2 pcs - P16 Plastic Bracket
8 pcs - H8 Philips Round 1 pc - P1L Left Front Leg 1 pc - T1 Allen Wrench
Head Screw 1 pc - P2 Front Top Apron
FIGURE 2
STEP 2:
Attach two Plastic Brackets P16 to top inside of
Front Leg Panel P6 with Philips Round Head
Screws H8 using pre-drilled holes as shown.
Next, attach Front Leg Panel P6 to Right Front
Leg P1R and Left Front Leg P1L with Philips
Round Head Screws H13 as shown in FIGURE 2.
Attach Front Top Apron P2 using Allen Head
Bolts H6 with Flat Washers H7 as shown.
Do not overtighten H6.
Next, secure Plastic Brackets P16 to underside
of Front Top Apron P2 with Philips Round Head
Screw H8 as shown in FIGURE 2.
P6
P2
P16
H8
H8
H6
H7
H13
P1R
P1L
NOTE:
Inside hook to
top of each
Leg P1.
All Rights Reserved
Note:
Make sure to place
steel inserts this side.
Note:
Make sure
to place steel
inserts this
side.
NOTE:
Cutout on
top side.
NOTE:
Small radius
on this side.
NOTE:
Laminate on this side -
Basketball Graphics other (Front) side.

STEP 3:
Attach Left Stiffener Boards P22L and Right Stiffener Boards P22R to inside of Leg Connecting Panel P8
using Philips Flat Head Screws H15. To finish securing the Left and Right Stiffener Boards, attach Metal
Connector H14 using Philips Round Head Screw H12 on the bottom side of Stiffener Boards where they join
as shown in DETAIL A.
To complete step, attach Leg Connecting Panel P8 assemblies to Front Legs (P1L & P1R) and Back Bottom
Leg (P3L & P3R) assemblies from STEP 1 and STEP 2 using Allen Head Bolts H11 with Flat Washers H7
as shown in FIGURE 3.
6
© 2011 Escalade Sports For Customer Service Call 1-888-996-2729
PARTS REQUIRED:
8 pcs - H7 Flat Washer 16 pcs - H15 Philips Flat Head Screw
4 pcs - H9Philips Washer Round Head Screw 4 pcs - P8 Leg Connecting Panel
8 pcs - H11 Allen Head Bolt 2 pcs - P22L Left Stiffener Board
24 pcs - H12 Philips Round Head Screw 2 pcs - P22R Right Stiffener Board
6 pcs - H14 Metal Connector 1 pc - T1 Allen Wrench
FIGURE 3
H9
H9
H15
H15
H9
H9
H11
H7
H11
H7
H12
H12
H14
H15
P22R
P22L
P22R
P8
P8
P8
P8
DETAIL A
P8
P22R
P22L
All Rights Reserved
P1L
P1R
P3L
P3R
P22L

STEP 4:
As shown in FIGURE 4, attach each Rim P17 to Backboard P9 using Allen Head Bolts H6, Rim Support
Plate P18, Lock Washers H16 and Locknuts H3. Use Allen Wrench T1 and Wench T2 to tighten Nuts and
Bolts. Next, attach Rim Net P20 to each Rim P17.
7
© 2011 Escalade Sports For Customer Service Call 1-888-996-2729
PARTS REQUIRED:
8 pcs - H3 Lock Nut 1 pc - P9 Backboard 2 pcs - P20 Rim Net
8 pcs - H6 Allen Head Bolt 2 pcs - P17 Rim 1 pc - T1 Allen Wrench
8 pcs - H16 Lock Washer 2 pcs - P18 Rim Support Plate 1 pc - T2 1/4” Wrench
All Rights Reserved
P9
T2
P17 T1
H16
H6
P18
H3
NOTE:
Rim Support Plate P18
attaches to back side
of backboard.
P20
P17
Install Net
onto Rim
FIGURE 4
PARTS REQUIRED:
8 pcs - H8 Philips Round Head Screw 4 pcs - H18 Lock Nut 1 pc - T1 Allen Wrench
4 pcs - H17 Philips Round Head Bolt 1 pc - P19 Electronic Scoreboard 1 pc - T3 4mm Wrench
STEP 5:
Attach Electronic Scoreboard P19 onto
the back side of Backboard P9 using
Philips Round Head Bolts H17 with Nuts
H18 as shown in FIGURE 5. Use the
wrench T3 to tighten Nuts.
Next, Install sensors as shown. Be sure
the color coded wires are placed as noted.
Use Screws H8 to attach each sensor.
White Wire
Black Wire
Grey Wire
Brown Wire
draobkcaBfoediSkcaB
H17
P9
H8
H18
T3
P19
FIGURE 5

STEP 6:
Attach Side Back Top Leg P4 to Left Back Top Leg P5L using Philips Round Head Screws H9, repeat this
procedure with Side Back Top Leg P4 and Right Back Top Leg P5R using Philips Round Head Screws H9.
Next, attach Backboard P9 to Right and Left side assembly with Allen Head Bolts H1 with Flat Washer H4
as shown in FIGURE 6. Use Allen Wrench T1 to tighten Bolts H1.
8
© 2011 Escalade Sports For Customer Service Call 1-888-996-2729
PARTS REQUIRED:
6 pcs - H1 Allen Head Bolt 2 pcs - P4 Side Back Top Leg
6 pcs - H4 Flat Washer 1 pc - P5L Left Back Top Leg
8 pcs - H9 Philips Round Head Screw 1 pc - P5R Right Back Top Leg
1 pc - T1 Allen Wrench
All Rights Reserved
FIGURE 6
H9
H4
H1
H1
H4
P4
P4
P5R
P5L P9
NOTE:
Two holes must be
at the bottom for correct
assembly.
NOTE:
Steel inserts must
be on the backside
of P5LA and P5R.

STEP 7:
Carefully slide Side Net Pole Supports P15 up through sleeve at back of Ramp Net P21 as shown
in FIGURE 7.
9
© 2011 Escalade Sports For Customer Service Call 1-888-996-2729
PARTS REQUIRED:
2 pcs - P15 Side Net Pole Support
1 pc - P21 Ramp Net
All Rights Reserved
FIGURE 7
P21
P15
P21
P15
NOTE:
The net ramp sleeve has a premade
hole in it and the welded nut on P15
must be correctly aligned with this
hole for future H6 bolt installation.
IMPORTANT NOTE:
This connecting strap
is sewn closed on one
side only.
Install P15 into unsewn
open side of this sleeve
connecting strap as
shown.

STEP 8:
To attach the Ramp Net P21, begin at
top of board assembly and secure both
sides of Ramp Net P21 using Allen
Head Bolt H6 with Flat Washer H7
as shown in DETAIL B.
Next, slide Steel Rod P13 through
sleeve at top of Ramp Net P21 and
secure to Side Back Top Leg P4 using
Allen Head Bolt H11 with Flat
Washer H7.
Be sure the bottom loop of Net
Support Pole P15 is between
Rod P13 and Side Board P4
as shown in DETAIL C.
To attach Steel Rod P14 to Side
Back Top Leg P4, place Allen
Head Bolt H5 and Flat Washer
H7 through the Side Back Top
Leg P4, and thread into the
P14 Rod end. Ramp Net must
be installed behind Steel Rod
P14 as shown.
Next, slide Steel Rod P12 into
sleeve at front of Ramp Net
P21.
10
© 2011 Escalade Sports For Customer Service Call 1-888-996-2729
PARTS REQUIRED:
2 pcs - H5 Allen Head Bolt 1 pc - P12 45” Front Ramp Support Round Tube
2 pcs - H6 Allen Head Bolt 1 pc - P13 45.5” Back Ramp Support Round Tube
6 pcs - H7 Flat Washer 1 pc - P14 45.875” Back Ramp Support Round Tube
2 pcs - H11 Allen Head Bolt 1 pc - T1 Allen Wrench
All Rights Reserved
FIGURE 8
DETAIL B
H7
H6 H6
H7
H11
H7
P4
P13
P15
DETAIL C
H11
H7
H6
H7
H11
H7
H5
H7
P4
P14
P13
P12
H5
H7

STEP 9:
With the help of another adult, attach upper back
board assembly from previous STEP 6 to lower
frame assembly.
First, thread two Bolts H1 with Flat Washer H4 into
each Side Back Top Leg P4 and two Bolts H1 with
Flat Washer H4 into each Left and Right Back Top
Leg P5L & P5R to secure the upper unit.
Next, assemble each Back Side Ramp Support
Tube P10 to Front Side Ramp Support Tube P11
using Philips Round Head Bolts H10 as shown in
FIGURE 9.
Attach assembled Support Tubes to both sides of
the frame on the top hole as shown using Bolts H2
with Flat Washers H7 and Nut H3.
Attach Support Tube at the front of the unit in top
hole as shown in FIGURE 9.
11
© 2011 Escalade Sports For Customer Service Call 1-888-996-2729
PARTS REQUIRED:
8 pcs - H1 Allen Head Bolt 8 pcs - H7 Flat Washer 2 pcs - P11 Front Side Ramp
4 pcs - H2 Allen Head Bolt 8 pcs - H10 Philips Round Head Bolt Support Tube
4 pcs - H3 Flat Washer 2 pcs - P10 Back Side Ramp 1 pc - T1 Allen Wrench
8 pcs - H4 Allen Head Bolt Support Tube 1 pc - T2 1/4” Wrench
All Rights Reserved
FIGURE 9
H1
H1
H4
H4
H2
H7
P4
P5L
P5R
H7
H3
H3
H7
H2
H7 P1L
P1R
NOTE:
Top Hole
P11
P10
H10
NOTE:
P11 Tube inserts into P10 Tube.

STEP 10:
Connect front of Ramp Net P21
and Steel Rod P12 using Allen
Head Bolts H5 and Flat Washers
H7 as shown in DETAIL D.
Lastly, attach Ramp Net Straps
to hook in Tube and Leg as
shown in DETAIL E & F.
12
© 2011 Escalade Sports For Customer Service Call 1-888-996-2729
PARTS REQUIRED:
2 pcs - H5 Allen Head Bolt
2 pcs - H7 Flat Washer
1 pc - T1 Allen Wrench
All Rights Reserved
DETAIL F
NOTE: Attach Ramp
Net Strap to hook in
Leg.
NOTE: Hook
inside the Leg.
FIGURE 10
DETAIL E
DETAIL D
H7
H5
P12
Tube
Velcro
Strap

13
© 2011 Escalade Sports For Customer Service Call 1-888-996-2729
All Rights Reserved
Congratulations! You have now assembled your double shootout. Please note the Care
and Use Instructions below to insure many years of trouble free use of this product.
ATTENTION
IF THE ASSEMBLY NEEDS TO BE MOVED, PICK UP FROM
FRONT AND BACK POSITION ONLY. DO NOT LIFT FROM
THE SIDES.
CARE AND USE OF YOUR SHOOTOUT
1. Use spray furniture polish to clean all exterior surfaces of your shootout.
2. Plug the adapter into a suitable 120v AC household outlet.
3. This product is intended for INDOOR use only.
4. DO NOT sit,climb or lean on the shootout.
5. DO NOT drag the shootout when moving it. This will damage the legs.
6. DO NOT set drinks on the shootout.
ADJUSTMENT AND USE OF YOUR SHOOTOUT
Plug the adapter into a suitable 120v household outlet and into the back of the scoring unit.
Each player has 30 seconds to make as many baskets as they can.During the first 20 seconds
each shot counts as 2 points. During the last 10 seconds each shot counts as 3 points.
Press the “RESET” button at the back of Electronic Scorer to start a new game.
NOTE:
You may also need to move the unit if you cannot get it to score correctly.
Sunlight or halogen lighting will have an effect on the sensors causing them to not
function properly. If the unit is relocated at a later date, the test procedure must be
repeated as explained below.
NOTE:
If you feel the performance of the electronic scoring sensors still do not function
properly, please follow these steps:
Step1: Push the “Play/Test” switch to “Test”.
Step2: To begin with the “Test” mode, the scorer should have “88” “88” “88” showing on the
electronic scoring display. Place a ball slowly at the top of the rim to test the top scoring sensor.
The top electronics sensor will read the ball and the electronic scorer should display changes
from “88” to “18” and making a “buzzing sound”. Then slowly place the ball at the bottom
of the rim to test the bottom electronic sensor. The bottom sensor will read the ball and the
electronic scorer should display changes from “88” to “81” and making a “buzzing sound”.
You have now calibrated the scoring sensors for the present light conditions.
If light conditions change, this same recalibration of the electronic scoring sensors may be
required for proper operation of the electronics scoring sensors.
Step3: Push the “Test” mode switch to “Play” to start your game.
NOTE:
There may be some types of shots that will not score every time.If two balls pass through
the rim at the same time it will not register both shots,The unit may also register a shot
when the ball passes quickly in front of the rim. These situations are normal.

14
© 2011 Escalade Sports For Customer Service Call 1-888-996-2729
All Rights Reserved
01474WJH1 H1 5/16” x 1” Allen Head Bolt 14
01474WJH2 H2 1/4” x 1-3/4” Allen Head Bolt 4
01474WJH3 H3 1/4” Lock Nut 12
01474WJH4 H4 5/16” x 19mm Flat Washer 14
01474WJH5 H5 1/4” x 1” Allen Head Bolt 12
01474WJH6 H6 1/4” x 7/8” Allen Head Bolt 12
01474WJH7 H7 1/4” x 15mm Flat Washer 34
01474WJH8 H8 4mm x 10mm Philips Round Head Screw 16
01474WJH9 H9 4mm x 1-3/4” Philips Washer Round Head Screw 12
01474WJH10 H10 4mm x 8mm Philips Round Head Bolt 8
01474WJH11 H11 1/4” x 1-1/8” Allen Head Bolt 10
01474WJH12 H12 4mm x 12mm Philips Round Head Screw 24
01474WJH13 H13 4mm x 18mm Philips Round Head Screw 4
01474WJH14 H14 Metal Connector 6
01474WJH15 H15 4mm x 1-3/4” Philips Flat Head Screw 16
01474WJH16 H16 1/4” Lock Washer 8
01474WJH17 H17 4mm x 20mm Philips Round Head Bolt 4
01474WJH18 H18 4mm Lock Nut 4
01474WJT1 T1 Allen Wrench 1
01474WJT2 T2 1/4” Wrench 1
01474WJT3 T3 4mm Wrench 1
01474WJA1 A1 Basketball 4
01474WJA2 A2 Air Pump with Needle 1
01474WJA3 A3 AC Adapter 1
01474WJP1R P1R Right Front Leg 1
01474WJP1L P1L Left Front Leg 1
01474WJP2 P2 Front Top Apron 1
01474WJP3L P3L Left Back Bottom Leg 1
01474WJP3R P3R Right Back Bottom Leg 1
01474WJP4 P4 Side Back Top Leg 2
01474WJP5L P5L Left Back Top Leg 1
01474WJP5R P5R Right Back Top Leg 1
01474WJP6 P6 Front Leg Panel 1
01474WJP7 P7 Back Leg Panel 2
01474WJP8 P8 Leg Connecting Panel 4
01474WJP9 P9 Backboard 1
01474WJP10 P10 Back Side Ramp Support Tube 2
01474WJP11 P11 Front Side Ramp Support Tube 2
01474WJP12 P12 45” Front Ramp Support Round Tube 1
01474WJP13 P13 45.5” Back Ramp Support Round Tube 1
01474WJP14 P14 45.875” Back Ramp Support Round Tube 1
01474WJP15 P15 Side Net Pole Support 2
01474WJP16 P16 Plastic Bracket 2
01474WJP17 P17 Rim 2
01474WJP18 P18 Rim Support Plate 2
01474WJP19 P19 Electronic Scoreboard with Sensors 1
01474WJP20 P20 Rim Net 2
01474WJP21 P21 Ramp Net 1
01474WJP22L P22L Left Stiffener Board 2
01474WJP22R P22R Right Stiffener Board 2
01474WJK1 K1 Hardware Kit 1
01474WJM1 M1 Owners Manual 1
PART# KEY# DESCRIPTION QTY.
PRODUCT PARTS LIST

15
© 2011 Escalade Sports For Customer Service Call 1-888-996-2729
All Rights Reserved
This consumer warranty extends to the original consumer purchase of any ESCALADESPORTS
Product (hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a pe-
riod of 90 days from the original purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser
that any Product of its manufacture is free from defects in material and workmanship when used
for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE
PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE,
IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS PROVIDED WITH THE PROD-
UCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND WORKMAN-
SHIP.
WARRANTY PERFORMANCE: During the above 90 day warranty period, ESCALADESPORTS
shall repair or replace with a comparable model, and Product, or component thereof, which may
prove defective under normal use and proper care, and which our examination shall disclose to
our satisfaction to be thus defective, please contact our Warranty Dept.
1-888-996-2729 / Warranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706
Attn: Warranty Dept.
Or E-mail us at:
[email protected]
Other than shipping requirements no charge will be made for such repair or replacement of in-
warranty Products. ESCALADE SPORTS strongly recommends that the Product is insured for
value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF
THIS SALE, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIM-
ITED IN DURATION TO THE ABOVE 90 DAY PERIOD. ESCALADE SPORTS
SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER
CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES IN-
CURRED BY THE CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or
incidental damages, so the above limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other
rights which may vary from state to state.
90 DAY LIMITED WARRANTY