RHYTHM Lifestyle Mobility Aids H800-1-002 User manual

H800-1-002
Adjustable
Tilting
Overbed
Table
55 lbs

USER MANUAL - H800-1-002 ADJUSTABLE TILTING OVERBED TABLE
GENERAL EXPLANATION
PARTS DIAGRAM
Prior to assembly please read all instructions and save for future use. If you do not understand any part of these instructions,
contact a health care professional or authorized dealer for assistance.
Tilting Table Top
Height Adjustment Lever
Rear Locking Casters
2
If any components are damaged or missing, contact your authorized dealer immediately.
Table Top
1
Column Assembly
2
Adjustment Lever
3
Mounting Tube
4
Inner Rod
5
Outer Tube
6
Base
7
Casters, Locking (2 each)
8
Casters, Non-Locking (2 each)
9
11
12
13
Black Screw (DO NOT REMOVE until assembled)
14
Chrome Screw A (DO NOT REMOVE)
15
Bolt Plate
- 15 x 2" Hex Bolts (2 each)
3/8
Chrome Screw B (To replace Black Screw after assembled)
16
Tilt Adjustment Knob
Tilt Adjustment Knob
Spacer
17
10 Bolt Sleeves (2 each)
7
11
12
13
14
9
8
4
3
16
15
5 6
17

DO NOT overtighten or use power tools to assemble.
ASSEMBLY INSTRUCTIONS
Place the Table Top (1) on a level surface so the
Mounting Tube (4) faces up.
1
2
1
3
5
DO NOT remove the Black Screw from Column Assembly until Table is fully assembled. This product utilizes a high
tension, spring loaded mechanism and could raise suddenly causing personal injury.
Install the Column Assembly (2) by inserting the
Outer Tube (6) and Inner Rod (5) through the
Mounting Tube (4). Add the Spacer (14) and Tilt
Adjustment Knob (13) to the Inner Rod (5) and tighten.
Take the Base (7) with the caster holes facing away
from the Table Top (1) and place the end with the mounting
holes on the Column Assembly (2). Insert the 2 large hex
bolts (12) through the Bolt Plate (11), through the Bolt
Sleeves (10), through the Base (7) and into the Column
Assembly (2). Then tighten with a wrench.
Insert the Locking Casters (8) into the Base near the
Column Assembly and insert the Non-Locking Casters
(9) into the opposite end of the Base (7). Be sure to press
the casters in until they lock into place.
Turn the table upright placing the Casters on the floor.
While pressing down on the Table Top, remove the Black
Screw (15) in the Column Assembly (2) and replace it with
Chrome Screw B (17) included in the hardware package.
DO NOT REMOVE Chrome Screw A (16) below marked
“Do Not Remove”.
OPERATING INSTRUCTIONS
Apply light upward pressure anywhere on the table top and stop when the desired height is reached.
1
To Raise Table Top
Pull the Adjustment Lever upward and push down on the table top at the Column end. Do not put pressure on the opposite
end. When the Adjustment Lever is released, the Table Top will lock into place.
To Lower Table Top
The Casters on the Column end can be locked by stepping down on the tabs. To unlock, pull up on the tabs.
To Lock and Unlock Casters
Turn the Tilt Adjustment Knob to the left to loosen. Tilt the Table Top to the desired angle and turn the Tilt Adjustment Knob
to the right to tighten.
To Tilt Table Top

Full Electric Bed Transfer Bench Shower Sprayer
SAFETY PRECAUTIONS
MAINTENANCE
WARRANTY
Improper use of this product may result in personal injury and/or property damage. Lifestyle Mobility Aids is not liable for personal injury or
property damage due to failure to follow the instructions or recommendations in this manual or improper use of this product.
If you discover a problem, contact your Lifestyle Mobility Aids Dealer for assistance.
This product is designed as a portable surface for reading, eating and keeping small personal items within reach for INDOOR
use only.
The weight capacity is 55 lbs evenly distributed. Do not exceed this limit. Do not lean on the suspended end of the table top
as this may cause the table to tip.
Do not use as a walker or as an aid when sitting down or standing up.
Clean, as necessary, with a soft cloth using a mild detergent and water. Rinse and dry thoroughly before use.
Do not use organic solvents, such as acetone or abrasive cleansers.
Inspect weekly for wear and to ensure all components are secure. If any component appears worn or is not working
properly, contact your dealer for repair and/or appropriate replacement parts.
Limited Lifetime warranty is provided against any factory defects in material or workmanship of the frame.
One (1) year warranty against defective materials or workmanship on all other components, assemblies and parts.
This warranty does not cover product failure due to misuse, negligence, improper storage or handling, improper
operation or unauthorized modifications.
This warranty does not extend to non-durable components which are subject to normal wear and tear and need
periodic replacement.
For warranty service, it is recommended but not required that the product be returned to the Lifestyle Mobility
Aids dealer through whom it was originally purchased. However, all Lifestyle Mobility Aids Dealers are qualified
to assist you in obtaining warranty service. If the product is to be returned to Lifestyle Mobility Aids, prior
authorization will be required. In the event of a defect covered by this warranty, Lifestyle Mobility Aids will
determine if the product will be repaired or replaced.
Lifestyle Mobility Aids products are identified by a serial or lot number label at the time of manufacture. Removing
or defacing the label may void this warranty. If you have questions about your Lifestyle Mobility Aids product or
this warranty, please contact us at [e-mail].