Ribao CS-600A User manual

COIN SORTER
CS-600A
OPERATION INSTRUCTIONS

CS-600A Operation Instructions V1.1
Page 2 of 16
Content
1. Introduction………………………….…………………………3
2．Specifications………………………………………………….4
3. Key Panel……………………………………………………….4
4. Precautions…………………………………………………….5
5.Operating Procedures………………………………….....….6
6.Printer operation and paper assembly …………..………10
7.Set up the Coin Bag………..………...………...…..………. 11
8.Set up the Coin Tube Holder（option）……...…..………. 11
9.Troubleshooting………………………….…………………..13
10.Daily Maintenance………………….……….……………...14

CS-600A Operation Instructions V1.1
Page 3 of 16
Introduction
CS-600A coin sorting machine can sort six kinds of coins at the same time and
count, display, store and print the counting number, the value of each
denomination and the counting sum, the value sum of all coins. And it can
display and store the counting number and value for different cash registers.

CS-600A Operation Instructions V1.1
Page 4 of 16
Specifications
Sorting speed approx. 600coins/ min.
Hopper capacity approx.600pcs.
Coin denomination diameter 14-31mm
Coin thickness ≦4mm
Sorting number 1-6 different coins.
Dimension : 510×280×320mm
Weight: 16Kg
Power Consumption 30W
Power Supply AC 120V ± 10%, 60Hz
or AC 220V ± 10%, 50Hz
Display 8 Digits (LED Display)
Ambient Temperature 0-40C°
Humidity 30-75%
Key Panel

CS-600A Operation Instructions V1.1
Page 5 of 16
Key Function:
1）START/STOP：Start and Stop
2）LIST：List counted results
3）and ：Select the list of different Channels / memory units
4）CLR：Clear
5）REV：Reverse of the motor
6）VAL：To switch the display mode between quantity and amount
7）BAT：Batch setting
8）MT：Memory
9）MR：Memory Reading
10）M+：Accumulate the current counted number with previous data and
save
11）PRINT：Print the list of quantity、value of coins
12）+1000、+100、+10、+1：Numeric keys
Display modes：
1）Amount display : 0.00, with decimal point;
2）Quantity display: 0, no decimal point;
3）Total display: 0, No Channel number;
4）Single Channel display: 1- 0, With Channel number“1-”.
Precautions
·Use the power cable and communication cable supplied with this machine.
·Unplug the machine before moving it.
·Avoid operation under direct sunlight.
·Do not place your head, hand, tools and clothes near the hopper to avoid
injury and malfunction of the machine.
·Don’t open the cover during operation. When opening the hopper, make sure
that the machine is not in operation.

CS-600A Operation Instructions V1.1
Page 6 of 16
Operating Procedures
·Turn on the power switch，the display
shows the amount as right picture, with
decimal point.
·Press START/STOP to start, the
machine automatically enters into
amount display mode, with decimal point. After start, the motor rotates and
counting starts.
·In Amount display mode, press LIST
key to enter into single channel display
mode, with channel number in the front,.
·In Single channel modes, press 、
key to select different channels. In
Amount display modes, 、keys
are void.
·In single channel modes, press LIST key to enter into Amount display.
·In single channel modes, press START/STOP key to return to quantity
display and motor rotates and starts to count.
·Press VAL key to switch between
amount and quantity:

CS-600A Operation Instructions V1.1
Page 7 of 16
Data Clearance:
·In single channel modes, press
CLR to clear the data of this channel
only;
·In total mode, press CLR key to clear
all the data
Data save:
·Press MT key to save the data and
the indicating lamp is on
·Indicating lamp ON means the
channel is with data saved inside;
·In single channel modes, press MT to
save the data of this channel only;
·In total mode, press MT to save the data of all the channels.
Read out the memory:
·In single channel modes, press MR to
read out this channel only;
·In total mode, press MR to read the
total.

CS-600A Operation Instructions V1.1
Page 8 of 16
Memory Clearance:
·First press CLR key to clear the current data;
·Then press MT to clear data. After data is removed, the indicating lamp
goes out.
Accumulation saving:
·Press M+ key to accumulate the
current data with the previously
counted data, then save it and the
display is zero.
Similar to data saving procedure:
·In single channel modes, accumulate only the data of this channel;
·In total mode, accumulate the data in all the channels.
Batch setting:
·Press BAT key to enter into batch
setting mode.

CS-600A Operation Instructions V1.1
Page 9 of 16
Note ：If batch No.≠0, when it
achieves, the motor stops and the
display shows as right picture. It blinks
to display the first channel that
achieves, blinking means aother
channel also achieves. After noting
down, press START/STOPKey, it displays the next channel that achieves.
When there are no other channel achieving the batch quantity, it displays
normally. Press START/STOP Key, the machine starts to work again.
Note：As it is a rail sorter, when batch number is achieved, the motor will
stop, but there are still some coins in the passage, and these coins finally roll
into the drawer. The machine will display the actually counted number.
Batch setting procedure:
·Press CLR to clear to Zero;
·+1000、+100、+10、+1 keys are for batch number setting:
①+1000 is 1000, +100 is 100, +10 is 10, +1 is 1;
②One press increase the digit by 1. e.g. press +1 key once is 1,
double press is 2;
·Press and to switch channels.
After setting is OK, exit as follows;
·Press BAT key to exit and enter into total quantity display mode;
·Press START/STOP key to exit and enter into standard mode.
Value setting:
·Keep pressing VAL key and turn on
the power to enter into value setting
mode.

CS-600A Operation Instructions V1.1
Page 10 of 16
·Press CLR key to clear to Zero;
·+1000、+100、+10、+1 keys are for value setting:
①+1000 is 10, +100 is 1, +10 is 0.1, +1 is 0.01;
②One press increase the digit by 1. e.g. press +1 key once is 0.01,
double press is 0.02;
·Press and to select different channels.
·After setting, press VAL key to exit and enter total display.
Printer operation and paper assembly(option)
A. Printer operation
After switching on the power, press SEL key on the printer to select the
connection mode（RS232）with the sorter. In this case, the lamp is on. It means
that the printer is on-line and the data can be received. Normally the printer
should be in this mode, so the printer could print the counting report at any
time. If the lamp is not on, the printer is off-line. It cannot receive the data. In
this case, you can feed the paper by pressing LF key. Subsequently, you can
stop the paper feeding by pressing LF key. During printing, the printer can be
stopped by pressing SEL key.
B. Paper Assembly
Push the cover，then take out the printer
and hold tightly the two ends of paper axis,
remove it from the fixed notch, renew the
paper tape roll and return it into the fixed
notch. By pressing SEL key ,switch off the
lamp; lead the print paper to the notch of
feed paper, then feed the paper by
pressing the LF key. Install the cover, press the SEL key, switch on the lamp
and it returns to the ready printing mode.