Coinco Guardian GLX Series Original operating instructions

Disclaimer
This is not designed to be a comprehensive guide
for the Guardian GLX.
Installing the Changer
1. Remove power from the vending machine. DO
NOT connect the changer harness to the
vending machine with power connected.
2. Remove the acceptor from the changer
housing by pressing the Acceptor Release
Latch (see Figure 1) to the right and then pull
the escrow lever towards you, away from the
changer housing.
3. Disconnect the two harnesses from the
acceptor (see Figure 2). Lift the acceptor
slightly to free the lower acceptor studs from
the changer housing. Place the acceptor in a
clean, dry area.
4. Set the three mounting holes in the back of the
changer housing over the mounting screws in
the vending machine. Tighten securely by
hand.
5. Reinstall the acceptor by inserting the lower
acceptor studs into the changing housing.
Plug the two harnesses into the acceptor.
Press the top of the acceptor into the changer
housing until the acceptor latch engages the
changer housing.
6. Verify the vendor’s coin return mechanism is
adjusted so that the acceptor gate is fully
closed. There should be a small gap between
the coin return and the changer escrow lever.
7. Plug the changer harness into the vending
machine.
8. Apply power to the vending machine.
9. The changer will power up, perform an auto-
test of all systems, then display “Status: OK”.
Guardian GLX Coin Changer
Installation & Operation Guide
Acceptor Gate
Escrow Lever
LCD Display
User
Interface
Keypad
Acceptor
Docking
Cradle
Sorting Door
Latch
Graduated
Tube Scales
Acceptor
Release Latch
Acceptor
Sorting Door
Coin
Denomination
Markings
Cassette
Handle
Figure 2. Disconnecting the 2 harnesses.
Escrow Lever
Acceptor
Release Latch
Figure 1. Removing the acceptor.

Loading Coins
10. Remove the coin tube cassette to load coins
into the coin tubes.
11. Raise the cassette handle and lift the coin tube
cassette up, then slide the cassette out of the
coin changer housing (See Figure 3).
12. Refer to the coin denomination labels at the top
of each coin tube and fill the 6 coin tubes to the
desired level with the appropriate coins.
VERIFY THAT ALL COINS LAY FLAT IN
EACH COIN TUBE.
Fill each coin tube with a minimum of 5 coins.
DO NOT fill the coin tubes above the 100%
mark!
NOTE: If you do not plan on using all 6 coin
tubes, make sure that you disable coin routing
to the unused tubes in the acceptor
programming. Use: MENU-SETUP-
CASSETTE-CUSTOM and set the unused
tubes to “---“
13. To reinstall the coin tube cassette, the 2 studs
located on each side of the cassette must line
up with the receiving slots on the changer
housing. Use the cassette handle to lift and
position the coin tube cassette with the coin
changer housing. Slide the cassette into the
housing. The coin tube cassette will slide into
the housing then drop down against the bottom
payout section of the coin changer when it is
correctly installed (See Figure 3).
14. Pay out at least 2 coins from each tube to
ensure proper operation. Press each coin tube
Inventory Button (See Figure 4) to dispense
coins.
15. Drop a variety of coins into the changer to
ensure proper operation.
For additional information, please contact your local
Coinco Sales Representative or visit our website at
coinco.com.
Coinco Publication #928523 12/2015
Cassette
Stud
Receiving
Slot
Cassette
Stud
Receiving
Slot
Figure 3. Removing and Reinstalling Lift-out Cassette.
Coin Acceptors, Inc.
U.S. Customers
1-800-325-2646
Canadian Customers
1-800-387-9300
www.coinco.com
Figure 4. Navigating the Main Menu.
Menu Navigation
General Navigation
Up/Down
Arrows: Show
options are
available above
& below
“Audit”.
Right Arrow:
Move across
screen or selects
current item.
Enter: Select
current item or
accept/close
operation.
Upper Level Menu:
Current Menu:
Lower Case for
this menu.
Up Arrow:
Scroll up in
current menu.
Left Arrow: Go
back one menu
level.
Letters: For
tube payout or
password
actions.
Cancel: Exit
out of
operation or
go up one
menu level.
Down Arrow:
Scroll down in
current menu.
MAIN MENU
Audit