RIED ControLaser QWP 800 User manual

OWNER'S MANUAL
Model: ControLaser QWP 800
Design and Specifications are subject to change without notice.
PLEASE READ CAREFULLY BEFORE USING AND KEEP WELL.
7" DIGITAL WATERPROOF LCD MONITOR
FOR HEAVY DUTY INDUSTRY

OWNER'S RECORD
r
The model and serial numbers are located on the rear of the unit.
Record the serial number in the space provided below. Refer to these
numbers whenever you call upon your dealer regarding this product.
To avoid electric shock, do not open the cabinet. Refer servicing to
qualified personnel only.
Model No. ControLaser QWP 800
Serial No.
WARNING
This symbol is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to constitute risk of electric
shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance(servicing) instructions in the
literature accompanying the appliance.
You are cautioned that any changes or modifications which is not expressed
or approved in this manual could void your warranty and cause the equipment
to malfunction.
2

r
Manual
DC
1. PLEASE USE THE PRODUCT AFTER READING THE MANUAL
CAREFULLY FOR SAFE USAGE.
PLEASE INSTALL AND USE THE PRODUCT AFTER FULLY AWARE
OF THE MANUAL AND PRECAUTION.
6. CONNECT THE MAIN POWER AFTER INSTALLATION.
IT CAN CAUSE PRODUCT MALFUNCTION, FIRE AND ELECTRIC
SHOCK.
8. THE PRODUCT IS DESIGNED FOR NORMAL CONDITION USAGE.
PLEASE FULLY CONSULT AND DISCUSS WITH YOUR DEALER OR
MANUFACTURER IF YOU NEED TO USE THE PRODUCT IN SPECIAL
CONDITION.
2. ASK EXPERIENCED TECHNICIAN FOR PRODUCT INSTALLATION.
INSTALLATION SHOULD BE DONE BY THE TECHNICIAN DUE TO
PROFESSIONAL SKILLS AND EXPERIENCE IS REQUIRED.
3. DO NOT INSTALL, OPEN OR MODIFY THE PRODUCT RANDOMLY.
IT CAN CAUSE PRODUCT MALFUNCTION, ELECTRIC SHOCK,
FIRE AND ALSO WATERPROOF PROBLEM FOR WATERPROOF
PRODUCT.
CONTACT THE SERVICE CENTER AND ASK FOR A/S, IF REPAIRS
ARE NECESSARY.
4. USE REGULATED VOLTAGE.
PROTECTION CIRCUIT IS BUILT INSIDE BUT OVER VOLTAGE
USAGE CAN CAUSE DAMAGE TO THE PRODUCT.
MANUFACTURER WILL NOT TAKE RESPONSIBILITY FOR THE
PRODUCT MALFUNCTION CAUSED BY OVER VOLTAGE.
5. DO NOT DROP OR GIVE EXTERNAL SHOCK TO THE PRODUCT.
THE PRODUCT SCREEN OR EXTERIOR CAN BE DAMAGED AND
CAUSE MALFUNCTION OF THE INTERNAL PARTS.
IN THIS CASE NORMAL CUSTOMER SUPPORT AND A/S CAN'T BE
RECEIVED.
7. USE AUTHORIZED ACCESSORY & COMPONENTS.
USING UNAUTHORIZED ACCESSORY & COMPONENTS CAN CAUSE
PRODUCT MALFUNCTION AND THE MANUFACTURER WILL NOT
TAKE RESPONSIBILITY FOR THE MALFUNCTION.
OTHERWISE, IT CAN CAUSE PRODUCT MALFUNCTION IN
ABNORMAL CONDITION USAGE.
CAUTION BEFORE USAGE
3

r
A/S
4
SAFETY&CAUTION DURING USAGE
- DO NOT CUT OR DAMAGE THE CABLE RANDOMLY.
IT CAN CAUSE PRODUCT MALFUNCTION OR WATERPROOF FUNCTION
DEFECT.
MANUFACTURER WILL NOT TAKE RESPONSIBILITY FOR THE MALFUNCTION.
- TIGHTEN THE CONNECTORS WHEN CONNECTING THE EXTENSION CABLE.
OTHERWISE, IT CAN CAUSE CONNECTION PROBLEM OR WATERPROOF
FUNCTION DEFECT OF THE PRODUCT.
- MAKE SURE TO CONNECT POWER CABLE AND CAMERA CABLE IN RIGHT
DIRECTION.
WRONG WIRE CONNECTION CAN CAUSE DAMAGE TO THE PRODUCT.
- DO NOT APPLY EXCESSIVE PRESSURE TO THE LCD.
DUE TO PRESSURE THERE COULD BE SPOTS ON THE LCD SURFACE AND
GET DAMAGED.
EXCHANGE FOR THE DAMAGE IS PROVIDED AT A COST.
- DO NOT DROP THE PRODUCT IN THE WATER OR KEEP IN HUMID PLACE
FOR A LONG TIME.
IT WILL BE CLASSIFIED AS INUNDATION REASON AND WON'T BE ABLE TO
GET FREE A/S SERVICE. (NON-WATERPROOF MONITOR)
- CHECK THE FIXED CONDITION OF THE BRACKET AND PRODUCT BEFORE
DRIVING. IT CAN CAUSE DAMAGE WHILE DRIVING IN UNSTABLE CONDITION
BY PHYSICAL PHENOMENONS. MANUFACTURER WILL NOT TAKE
FOR USER'S NEGLIGENCE.
- DO NOT USE THE PRODUCT IMMEDIATELY AFTER LEAVING ALONE FOR
A LONG PERIOD IN SUMMER OR WINTER.
IT CAN CAUSE SERIOUS DAMAGE TO THE PRODUCT WHEN USING IN
INAPPROPRIATE .
- STOP USING THE PRODUCT IMMEDIATELY IF BURNING SMELL, SMOKE
OR SEVERE OVERHEATING OCCURS WHILE USAGE AND VISIT THE A/S
CENTER.
- WHEN USING TOUCH KEY EQUIPPED PRODUCT THE WATERPROOF
FUNCTION WILL NORMALLY OPERATE, BUT IF THERE IS WATER ON THE
TOUCH KEY PANEL IT COULD CAUSE MALFUNCTION.
SO PLEASE REMOVE THE MOISTURE BEFORE USAGE.
RESPONSIBILITY
TEMPERATURE

rSAFETY&CAUTION DURING USAGE
5
- DO NOT WRAP THE PRODUCT WITH ANY FABRIC WHILE OPERATING.
DUE TO INTERNAL TEMPERATURE RISING, IT CAN CAUSE PRODUCT
MALFUNCTION OR FIRE.
- AVOID SEVERE ELECTROSTATIC CONDITION.
IT CAN CAUSE PRODUCT MALFUNCTION.
- DO NOT PILE UP HEAVY STUFF ON THE PRODUCT.
IT CAN CAUSE PRODUCT PROBLEMS OR DAMAGE.
- DO NOT PRESS SEVERAL BUTTONS AT THE SAME TIME.
- IF ANY DEBRIS IS FOUND INSIDE OF THE PRODUCT, DISCONNECT THE
POWER CABLE AND VISIT THE A/S CENTER.
IT CAN CAUSE ELECTRIC SHOCK OR MALFUNCTION WHEN USED
CONTINUOUSLY.
- DO NOT CLEAN THE PRODUCT WITH CHEMICAL PRODUCT
(ALCOHOL, BENZENE, ACETONE AND ECT).
IT CAN CAUSE DAMAGE OF THE PRODUCT SURFACE OR PRODUCT
MALFUNCTION.

rSUGGESTIONS
7" DIGITAL TFT LCD COLOR
ALL ROUND VISION MONITOR
Safety
1
Use only DC 10V ~ DC 32V.
If liquid or dust leaks into the case, turn off power to the unit and consult an
experienced technician before using.
Installation
2
Do not install the units in an extremely hot or humid place (radiator, air duct,
etc.) or in a place subject to direct sunlight, excessive dust, mechanical
vibration or shock. If your vehicle has been parked in direct sun light resulting
in a considerable rise in temperature inside the vehicle, allow the unit to cool
off before operating.
General cleaning information
3
Clean the unit with a slightly damp soft cloth. Use a mild household detergent.
Never use strong solvents such as thinner or benzene as they might damage
the finish of the unit.
rFEATURES
ControLaser QWP 800 (7" Digital TFT LCD Monitor)is especially
designed as automotive all round vision system.
6
Wa t e r Proof (IP65)
7" Dig i t a l L C D W i de Panel
Auto N T S C / PAL Detection
Auto D AY/NIGHT Detection
Multi p l e d i s p l a y modes (SINGLE, SPLIT, TRIPLE, P I P, Q U A D )
Adjus t a b l e S p e e d switch
Va n d a l Resistance (Al Housing)
Suppo r t Various Divide Modes
Parki n g D i s t a n c e Marker Setting Av a i l a b l e
Capac i t i v e Tou c h Key
Support Multi-Functional Camera (CAM1 &CAM2): Normal/Shutter/Tilt

ControLaser QWP 800 MONITOR
POWER CORD
4P IP TYPE
CAMERA CONNECTOR
4P DIN TYPE
CAMERA CONNECTOR
or
SCREW KITS
INSTRUCTION
MANUAL
STAND BRACKET
OPTIONAL
OR
OWNER'S MANUAL
Model: ControLaser QWP 800
De si gn an d Sp ec ifi ca ti on s are s ub je ct t o cha ng e wi th out n ot ic e.
PLE ASE REA D CAREF ULLY BEFO RE USIN G AN D KEEP WE LL.
7" DIGITA L WATERPRO OF LCD MONITO R
FOR HEAVY DU TY INDUSTR Y
rPACKAGE CONTENTS
Please check that you have the correct contents before using this product. If
any items are missing, please contact your dealer.
7

POWER
2
Touch to turn the monitor on.
Touch to turn the monitor off.
Touch to select CAMERA.
Touch to select the option in SET UP MENU.
Use to enter Display Menu(Short key) and
Main Menu(Long key).
Touch once to enter menu mode.
Touch again to exit from menu mode.
Selectable OSD Menu Disappears within 7 sec if there’s
no new button pressed.
Touch menu button over 2 sec to go back to main menu
from submenu.
3MENU
POWER
MENU
UP
DOWN
DAY/NIGHT SENSOR
UP DOWN
4 5
DAY/NIGHT SENSOR
6
While in Menu mode and navigate though
the available menu options.
Touch to adjust Bright, Contrast, Color, Tint
Volume and other setting values.
The brightness of the monitor is adjusted automatically
with the DAY/NIGHT SENSOR accordingly to the circumstance.
Automatic Brightness Control
1
1
2
3
4
5
6
Monitor start mode will follow “AUTO POWER SETTING”
2NOTE NOTE
SELECT
SELECT
SEL
MENU
MENU
SEL
SEL
1
2
3
4
5
6
OPERATIONS
r
8

OPERATIONS
r
9
TI NT
* menu is displayed in NTSC only.
BR IG HT
CO NT RAST
CO LO R
TI NT
DI SP LAY MEN U
30
30
30
30
BRIG H T
CONT R A ST
COLO R
TINT
PAL MODE NTSC MODE
30
(0~60)
30
(0~60)
30
(0~60)
30
(0~60)
.DISPLAY MENU
MENU UP / DN SELECTSELECT SELECTSELECT
DN DN
Option setting
Short Key
(more than 0.5 sec)
UP / DN
MENU
SEL SEL

OPERATIONS
r
10
MAI N MEN U
1. CAMERA SETTING
2. TRIGGER SETTING
3. SPLIT SETTING
4. SPEED SWITCH
5. DAY/NIGHT SETTING
6. AUTO SCAN SETTING
7. ADVANCED MENU
.SETUP MENU
Touch MENU button for a while (over 2 secs) to enter MAIN MENU.
Selectable OSD MENU disappears within 7 secs if there is no new button pressed.
long key
(more than 2 sec) up / down shifting
A
A
option setting
MENU UP / DN SELECTSELECT
MENU
SEL
** SEL ▶
** UP/DN ▶
** MENU ▶
Ex ) Setting Cam2 as normal view
Enter to Sub Menu of Previous one
or Value adjustment.
Shifting menu or Value adjustment
Exit to upper menu (Value is saved)
→UP/DN to CAM2 → SEL → UP/DN to Nor/Mir →
Adjust value with SEL → MENU to save and quit to upper MENU
→ →
Bright, Contrast and Color value for each channel(CAM1~4, AUX) can be
controlled in SUBDIVISION Menu
CAMERA SETTING
1
CAM1
CAM2
CAM3
CAM4
AUX
1. CAMERA SETTING
SUBDIVISION MENU
NOR/MIR : [MIRROR;NORMAL]
N A M E : [ C A M 1 ]
SORT:[NORMAL;SHUTTER;
TILT.AT;TILT.MT]
UP/DOWN : [ ]U P ; D O W N
S U B D I V I S I O N M E N U
BR IG HT
CO NT RAST
CO LO R
SU B D I V ISION MENU U
30
30
30
A
selecting selecting selectingshifting value setting
UP / DN UP / DN
shifting
UP / DN
shifting
UP / DN
exit to upper menu
2NOTENOTE
MENU
MENU
SELECTSELECT
SEL
SELECTSELECT
SEL
SELECTSELECT
SEL