RiverGrille Stampede CG2053904-RG User manual

CG2053904-RG Page 1 of 22 20150821-V0
Stampede 37.5 Inch Charcoal Grill
Owner’s Manual
Assembly and Operating Instructions
Model # CG2053904-RG
Tools required for assembly: (Not Included) Pliers, Philips & Flathead Screwdrivers, Adjustable
Wrench.
Keep this manual for future reference.

CG2053904-RG Page 2 of 22 20150821-V0
WARNING
!Only use this grill on a hard, level, non-combustible, stable surface (concrete, ground, etc.) capable of
supporting the weight of the grill. Never use on wooden or other surfaces that could burn.
!When grill is in use, keep clearance of 36” between the hot grill and any combustible materials, such as
bushes, trees, wooden decks, wooden fences, buildings, etc. Do not place hot grill under roof overhang or in
any other enclosed area.
!The maximum weight of charcoal to be used is 3.5 pounds (1.59kg). Too much charcoal may cause the
surface coating peel off.
!FOR OUTDOOR USE ONLY. DO NOT operate grill indoors or in an enclosed area because of carbon
monoxide poisoning that can lead to personal injury or death.
!For household use only. Do not use this grill for other than its intended purpose.
!We recommend the use of a Charcoal chimney starter to avoid the dangers associated with charcoal lighting
fluid. If you choose to use charcoal lighting fluid, only use lighting fluid approved for lighting charcoal.
Carefully read manufacturer’s warnings and instructions on the charcoal lighting fluid and charcoal prior to
the use of their product. Store charcoal lighting fluid safely away from grill.
!When using charcoal lighting fluid, allow charcoal to burn with grill lid and doors open until covered with a
light ash (approximately 20 minutes). This will allow charcoal lighting fluid to burn off. Failure to do this could
trap fumes from charcoal lighting fluid in grill and may result in a flash fire or explosion when lid is opened.
!Do not use gasoline, kerosene or alcohol for lighting charcoal. Use of any of these or similar products could
cause an explosion possibly leading to severe bodily injury.
!Never add charcoal lighting fluid to hot or even warm coals as flashback may occur causing severe burns.
!Place grill in an area where children and pets cannot come into contact with unit. Close supervision is
necessary when grill is in use.
!Do not leave grill unattended when in use.
!When adding charcoal and / or wood, use extreme caution and follow instructions in “Adding Charcoal /
Wood During Cooking” section of this manual.
!Do not store or use grill near gasoline or other flammable liquids, gases or where flammable vapors may be
present.
!Do not store lighter fluid or other flammable liquids or materials under the grill.
!Use caution when adjusting charcoal grate height, use oven mitt. Handle will be hot when in use.
!Never raise or lower charcoal grate when water smoking as hot water may splash on to coals creating a burst
of hot steam and coals.
Grill is hot when in use. To avoid burns:
!DO NOT attempt to move the grill.
!Wear protective gloves or oven mitts.
!DO NOT touch any hot grill surfaces.
!DO NOT wear loose clothing or allow hair to come in contact with grill.
!
!

CG2053904-RG Page 3 of 22 20150821-V0
WARNING
!When grilling, grease from meat may drip into the charcoal and cause a grease fire. If this should happen
close lid to suffocate the flame. Do not use water to extinguish grease fires.
!Use caution when opening the lid, keep hands, face and body a safe distance away. Flash flare ups may
occur when air comes into contact with fire or hot coals.
!Never place more than 5 pounds (2.3 kg) on front and side tables.
!Do not allow charcoal and/or wood to rest on the walls of grill. Doing so will greatly reduce the life if the
metal and finish of your grill.
!Use caution during assembly and while operating your grill to avoid scrapes or cuts from sharp edges of
metal parts. Use caution when reaching into or under grill.
!When opening lid, be sure lid is fully opened and secure to prevent lid from closing unexpectedly.
!In windy weather, place grill in an outdoor area that is protected from the wind.
!Close lid to suffocate flame.
!Never leave coals and ashes in grill unattended, before grill can be left unattended, remaining coals and
ashes must be removed from grill. Use caution to protect yourself and property, carefully place remaining
coals and ashes in a non-combustible metal container and saturate completely with water, allow coals and
water to remain in metal container 24 hours prior to disposing.
!Extinguished coals and ashes should be placed a safe distance from all structure and combustible
materials.
!With a garden hose completely wet the surface beneath and around grill to extinguish any ashes, coals or
embers which may have fallen during the cooking or cleaning process.
!After each use, clean the grill thoroughly and apply a light coat of vegetable oil to prevent rusting. Cover
the grill to protect it from excessive rusting.
!Use caution when lifting or moving grill to prevent strains and back injuries.
!We advise that a fire extinguisher be on hand. Refer to your local authority to determine proper size and
type of fire extinguisher.
!Store the grill out of reach of children and in a dry location when not in use.
!Do not attempt to services grill other than normal maintenance as explained in “After-Use Safety” and
“Proper Care & Maintenance” sections of this manual.
!Properly dispose of all packaging material.
Use caution and common sense when operating your grill.
Failure to adhere to safety warning and guidelines in this manual could result in bodily injury or property
damage.
Save this manual for future reference.
ASSEMBLY INSTRUCTIONS
THANK YOU FOR PURCHASING THIS STAMPEDE 37.5 INCH GRILL
Read all safety warnings & assembly instructions carefully before assembling or operating your grill.
For missing parts, please call customer service at [e-mail] or
at 888-837-1380 (U.S. only),
Mon to Fri, 8:00 a.m. – 5:00 p.m. Pacific Standard Time.
(Proof of purchase will be required.)
Inspect contents of the box to ensure all parts are included and undamaged.
We recommend two people for assembly of this grill.
!
!

CG2053904-RG Page 4 of 22 20150821-V0
The following tools are required for assembly and are not included:
!Pliers
!Philips & Flathead Screwdrivers
!Adjustable Wrench
Product Diagram
11
22
7
3
15
1
2
5
6
21
20
16
13
17
8
10
9
4
14
18
19
12
23

CG2053904-RG Page 5 of 22 20150821-V0
Component List
1. Lid
2. Smoke Stack
3. Damper
4. Lid Handle
Qty. 1pc
Qty. 1pc
Qty. 1pc
Qty. 1pc
5. Temperature Gauge
Qty. 1pc
6. Warming Rack
Qty.1pc
7. Cooking Grid
Qty. 2pcs
8. Charcoal tray
hanger
Qty. 2pcs
9. Charcoal tray
10. Side Shelf
11. Fire Bowl
12. Front Shelf Slat
Qty. 1pc
Qty. 1pc
Qty. 1pc
Qty. 2pcs
13. Front Shelf Bracket
14. Front Shelf Support
15. Left Leg
16. Legs Connector
Qty. 2pcs
Qty.2pcs
Qty. 2pcs
Qty. 2pcs
17. legs holder
18. Right Leg
19. Wheel
20．Axle
Qty. 2pcs
Qty.2pcs
Qty.2pcs
Qty. 1pc
21.Bottom Rack
Qty. 1pc
22．Air Vent
Qty. 2pcs
23.Grease cup holder
Qty. 1pc

CG2053904-RG Page 6 of 22 20150821-V0
STOP! DO NOT RETURN TO RETAILER
For assembly assistance, missing or damaged parts, please contact customer service at,
[e-mail] or 888-837-1380 (U.S. only) Mon to Fri, 8:00 a.m. – 5:00 p.m.
Pacific Standard Time.
Hardware List
A
Bolt (M6X50)
12pcs
B
Bolt (M6X20)
4 pcs
C
Bolt (M6X12)
20pcs
D
Flange Nut (M6)
26pcs
E
Lock Nut (M8)
2 pcs
F
Lock Nut (M6)
2 pcs
G
Cap Nut (M8)
(2 pcs pre-assembled)
3 pc
H
Spring
1 pc
J
Cotter Pin
4 pcs
K
Hinge Pin
2 pcs
Assembly Procedures
Symbol: The following symbols will be shown in each procedure for
indication of tightening the bolt and nut if necessary.

CG2053904-RG Page 7 of 22 20150821-V0
Some steps may require the assistance of a friend.
Step 1. Assembly of left legs (15) with legs holder (17)
Hardware required: Bolt A x 4 pcs, Flange nut D x 4 pcs
Step 2. Assembly of right legs (18) with legs holder (17)
Hardware required: Bolt A x 4 pcs, Flange nut D x 4 pcs
Hand Tighten only at this time
Tighten with tools at this time

CG2053904-RG Page 8 of 22 20150821-V0
Step 3. Assembly the bottom rack (21) to left and right legs assembly and legs connector (16)
to form a cart frame.
Step 4. Assembly of wheels (19) and axle (20) to cart flame to form a grill cart.
Hardware required: Lock nut E x 2 pcs

CG2053904-RG Page 9 of 22 20150821-V0
Step 5. Assembly fire bowl (11) to grill cart
Hardware required: Bolt A x 4pcs, flange nut D x 4 pcs
Step 6. Tighten the bolts and nuts in steps 1,2 and 5.
Step7. Assembly air vent (22) to fire bowl. Adjust to suitable tightness for turning.
Hardware required: Bolt C x 2 pcs, lock nut F x 2 pcs

CG2053904-RG Page 10 of 22 20150821-V0
Step 8. Assembly side shelf 10 to fire bowl (11).
Hardware required: Bolt B x 4pcs, flange nut D x 4 pcs
Step 9. Assembly front table slats (12) with front table bracket (13) to form front shelf
assembly.
Hardware required: Bolt C x 6 pcs

CG2053904-RG Page 11 of 22 20150821-V0
Step 10.Assembly front shelf assembly to fire bowl(11)
Hardware required: Bolt C x 2 pcs, flange nut D x 2 pcs
Step 11.Assembly front table support (14) to front table assembly and fire bowl
Hardware required: Bolt C x 4 pcs, flange nut D x 2 pc

CG2053904-RG Page 12 of 22 20150821-V0
Step 12. Tighten the bolts and nuts in steps 9, 10 and 11.
Step 13.Assembly the temperature gauge (5) to lid (1). Then assembly smoke stack (2) to the lid
(1) and finally assembly the damper (3)..
Hardware required: Bolt C x 2 pcs, Flange nut D x 2 pcs, Cap nut G and spring H x 1 pc each.
Step 14. Assembly handle (4) to the lid
Hardware required: Bolt C x 4 pcs, flange nut D x 4 pcs

CG2053904-RG Page 13 of 22 20150821-V0
Step 15. Assembly lid to fire bowl.
Hardware required: Hinge Pin K x 2 pcs, cotter pin J x 2 pcs
Step 16. Install charcoal tray (9) to fire bowl with charcoal tray hangers (8)
J
K

CG2053904-RG Page 14 of 22 20150821-V0
Step 17. Install warming rack (6) to grill lid and fire bowl.
Hardware required: Cotter pin (J) x 2 pcs
Step 18. Install cooking grid (7) to fire bowl. Also install the grease cup holder (23) to fire bowl
underneath.
23

CG2053904-RG Page 15 of 22 20150821-V0
Final assembly
WARNING
Place the grill outdoors on a hard, level, non-combustible surface away from roof overhang or any combustible
material. Never use on wooden or other surfaces that could burn. Place the grill away from open windows or doors
to prevent smoke from entering your house. In windy weather, place the grill in an outdoor area that is protected
from the wind.
WARNING
Read all safety warnings and instructions carefully before operating your grill.
PREPARATION FOR USE & LIGHTING INSTRUCTIONS
Curing your grill
Prior to your first use of the Grill, follow the instructions below carefully to cure your grill. Curing your grill will
minimize damage to the exterior finish as well as get rid of the grill paint odor that can cause unnatural flavors to the
first meal prepared on the grill.
IMPORTANT: To protect your grill from excessive rust, the unit must be properly cured and covered at
all times when not in use.
!
!
!
!

CG2053904-RG Page 16 of 22 20150821-V0
Step 1
Lightly coat all interior surfaces of the grill with vegetable oil or vegetable oil spray. Do not coat charcoal grates or
racks.
Step 2
Follow the instructions below carefully to build a fire. You many use charcoal and/or wood as fuel in the grill (see
“Adding Charcoal/Wood During Cooking” section of this manual).
If using a Charcoal Chimney Starter, follow all manufacturer’s warnings and instructions regarding the use of their
product. Start with 3.5 pounds (1.59 kg) of charcoal.
Instruction for reference only:
1. Begin with three full sheets of newspaper.
2. Take 2 sheets of newspaper and roll each into a tube shape and then give them a little twist to form each of
them into a straight “rope” like shape. Be careful to not twist too tight.
3. Turn the charcoal chimney starter over and place both pieces of rolled and twisted newspaper along the inside
bottom of the charcoal chimney starter to form a complete circle. Leave a hole in the middle of the charcoal
chimney starter with no paper in it.
4. Crumple up the 3rd sheet of newspaper into a ball. Be careful to not crumple too tight. Sprinkle about 1 table
spoon of cooking oil on the ball of newspaper. You can also use a few sprits of cooking oil from a spray can.
Don’t use too much oil. Place the ball of cooking-oiled newspaper in the center of the charcoal chimney starter.
5. Flip the chimney over and add charcoal. Take care so that the newspaper does not fall out.
6. Use a match or long lighter to light the paper.
7. Stand back and watch the charcoal chimney starter do its stuff.
8. After charcoal has turned an ash gray color, carefully pour the charcoal onto your grill’s fire grate.
NOTE: To extend the life of your grill, make sure that hot coals and wood do not touch the walls of grill.
IF USING CHARCOAL CHIMNEY STARTER, PROCEED TO STEP 5.
If you choose to use charcoal lighting fluid, ONLY use charcoal lighting fluid approved for lighting charcoal. Do not
use gasoline, kerosene, alcohol or other flammable material for lighting charcoal. Follow all manufacturer’s warnings
and instructions regarding the use of their product. Start with 3.5 pounds (1.59kg) of charcoal. Place the charcoal in
the center of each charcoal grate.
Step 3
Saturate charcoal with lighting fluid. With lid open, wait 2 to 3 minutes to allow lighting fluid to soak into charcoal.
Store lighting fluid a safe distance from the grill.
Step 4
With grill lid open and charcoal grate completely placed inside the grill. Stand back and carefully light charcoal. Allow
to burn until covered with a light ash (approximately 20 minutes).
WARNING
Charcoal lighting fluid must be allowed to completely burn off prior to closing grill lid (approximately 20 minutes).
Failure to do this could trap fumes from charcoal lighting fluid in grill and may result in a flash-fire or explosion
when lid is opened.
Step 5
With coals burning strong, close the lid. Allow the temperature to reach 225°F (107°C) on temperature gauge.
Maintain this temperature for 2 hours.
Step 6
Increase the temperature to 400°F (205°C) on temperature gauge. This can be achieved by adding more charcoal
and/or wood (see “Adding Charcoal/Wood During Cooking“ section of this manual). Maintain this temperature for 1
hour then allow unit to cool completely.
!
!

CG2053904-RG Page 17 of 22 20150821-V0
NOTE: It is important that the exterior of the grill is not scraped or rubbed during the curing process.
IMPORTANT: to protect your smoker from excessive rust, the unit must be cured periodically and covered
at all times when not in use.
OPERATING INSTRUCTIONS
Step 1
Lightly coat all interior surfaces of the grill with vegetable oil or vegetable oil spray. Do not coat charcoal grate or
racks.
Step 2
Follow the instructions below carefully to build a fire. You may use charcoal and/or wood as fuel in the Barrel Grill
(see “Adding Charcoal/Wood During Cooking” section of this manual).
If using a Charcoal Chimney Starter, follow all manufacturer’s warnings and instructions regarding the use of their
product, start with 3.5 pounds (1.59 kg) of charcoal. When charcoal is burning strong, carefully place hot coals in
center of each charcoal grate.
Instruction for reference only:
1. Begin with three full sheets of newspaper.
2. Take 2 sheets of newspaper and roll each into a tube shape and then give them a little twist to form each of
them into a straight “rope” like shape. Be careful to not twist too tight.
3. Turn the charcoal chimney starter over and place both pieces of rolled and twisted newspaper along the inside
bottom of the charcoal chimney starter to form a complete circle. Leave a hole in the middle of the charcoal
chimney starter with no paper in it.
4. Crumple up the 3rd sheet of newspaper into a ball. Be careful to not crumple too tight. Sprinkle about 1 table
spoon of cooking oil on the ball of newspaper. You can also use a few sprits of cooking oil from a spray can.
Don’t use too much oil. Place the ball of cooking-oiled newspaper in the center of the charcoal chimney starter.
5. Flip the chimney over and add charcoal. Take care so that the newspaper does not fall out.
6. Use a match or long lighter to light the paper.
7. Stand back and watch the charcoal chimney starter do its stuff.
8. After charcoal has turned an ash gray color, carefully pour the charcoal onto your grill’s fire grate.
NOTE: to extend the life of your grill, make sure that hot coals and wood do not touch the walls of grill.
IF USING CHARCOAL CHIMNEY STARTER, PROCEED TO STEP 5.
If you choose to use charcoal lighting fluid, ONLY use charcoal lighting fluid approved for lighting charcoal. Do not
use gasoline, kerosene, alcohol or other flammable materials for lighting charcoal. Follow all manufacturer’s
warnings and instructions regarding the use of their product. Start with 3.5 pounds (approximate 1.59 kg) of charcoal.
Place the charcoal in center of each charcoal grate.
Step 3
Saturate charcoal with lighting fluid. With lid open and charcoal grate completely placed inside the grill, wait 2 to 3
minutes to allow lighting fluid to soak into charcoal. Store charcoal lighting fluid a safe distance from the grill.
Step 4
With grill lid open, stand back and carefully light charcoal and allow to burn until covered with a light ash
(approximately 20 minutes).

CG2053904-RG Page 18 of 22 20150821-V0
WARNING
Charcoal lighting fluid must be allowed to completely burn off prior to closing grill lid (approximately 20
minutes).Failure to do this could trap fumes from charcoal lighting fluid in grill and may result in a flash-fire or
explosion when lid is opened.
Step 5
Place cooking grates on grill support lips.
WARNING
Always wear oven mitts/gloves when adjusting cooking levels to protect your hands from burns.
Step 6
Place food on cooking grates and close grill lid. Always use a meat thermometer to ensure food is fully cooked
before removing from grill.
Step 7
Allow grill to cool completely, and then follow instructions in the “After-Use Safety” and “Proper Care & Maintenance”
sections of this manual.
Flavoring Wood
To obtain your favorite smoke flavor, experiment by using chunks, sticks or chips of flavor producing wood such as
hickory, pecan, apple, cherry, or mesquite. Most fruit or nut tree wood may be used for smoke flavoring. Do not use
resinous wood such as pine as it will produce an unpleasant taste.
Wood chunks or sticks 3” to 4” (7 to 10 cm) long and 1” to 2” (2 to 4 cm) thick work best. Unless the wood is still
green, soak the wood in water for 30 minutes or wrap each piece in foil and tear several small holes in the foil to
produce more smoke and prevent the wood from burning too quickly. Only a few pieces of wood are required to
obtain a good smoke flavor. A recommended amount for the grill is 5 to 6 wood chunks or sticks. Experiment by
using more wood for stronger smoke flavor or less wood for milder smoke flavor.
Additional flavoring wood should not have to be added during the cooking process. However, it may be necessary
when cooking very large pieces of food. Follow instructions and cautions in the “Adding Charcoal/Wood During
Cooking” section of this manual to avoid injury while adding wood.
Regulating Heat
To increase heat, add more wood and/or charcoal. Follow instructions in “Adding Charcoal/Wood During Cooking”
section of this manual.
To maintain the temperature, you may need to add more wood and/or charcoal during the cooking cycle.
NOTE: Dry wood burns hotter than charcoal, so you may want to increase the ratio of wood to charcoal to
increase the cooking temperature. Hardwood such as oak, hickory, mesquite, fruit and nut wood are an
excellent fuel because of their burning rate. When using wood as fuel, make sure the wood is seasoned
and dry. DO NOT use resinous wood such as pine as it will produce an unpleasant taste.
The amount of food determines the amount of lump charcoal or charcoal briquette to be used. Add
charcoal gradually and observe the grilling temperature via the temperature gauge. Adding too much
charcoal into the grill at a time may raise the burning temperature rapidly and cause damages to the grill.
!
!
!
!

CG2053904-RG Page 19 of 22 20150821-V0
Adding Charcoal/Wood During Cooking
Additional charcoal and/or wood may be required to maintain or increase cooking temperature.
Step 1
Stand back and carefully open grill lid. Use caution since flames can flare-up when fresh air suddenly comes in
contact with fire.
Step 2
Wearing oven mitts/gloves, lift up the cooking grates and place it on a clean and non-combustible surface. DO NOT
touch the grates by hand.
Step 3
Stand back a safe distance and use long cooking tongs to lightly brush aside ashes on hot coals. Use cooking tongs
to add charcoal and/or wood to charcoal grates, being careful not to stir-up ashes and sparks. If necessary, use your
Charcoal Chimney Starter to light additional charcoal and/or wood and add to existing fire.
WARNING
Never add charcoal lighting fluid to hot or even warm coals as flashback may occur causing severe burns.
Step 4
When charcoal is burning strong again, wear oven mitts/gloves and carefully return the charcoal grates to grill body.
Extinguish any hot ashes, coals or embers which may have fallen from the grill or beneath and around grill using
water hose.
AFTER-USE SAFETY
WARNING
!Always allow grill and all components to cool completely before handling.
!Never leave coals and ashes in grill unattended. Make sure coals and ashes are completely extinguished
before removing.
!Before grill can be left unattended, remaining coals and ashes must be removed from grill. Use caution to
protect yourself and property. Place remaining coals and ashes in a non-combustible metal container and
completely saturate with water. Allow coals and water to remain in metal container 24 hours prior to
disposing.
!Extinguished coals and ashes should be placed a safe distance from all structures and combustible
materials.
!With a garden hose, completely wet surface beneath and around the grill to extinguish any ashes, coals or
embers which may have fallen during the cooking or cleaning process.
!Cover and store grill in a protected area away from children and pets.
!
!
!
!

CG2053904-RG Page 20 of 22 20150821-V0
Proper Care & Maintenance
!Cure your grill periodically throughout the year to protect against excessive rust.
!To protect your grill from excessive rust, the unit must be properly cured and covered at all times when not in
use.
!Wash cooking grates and charcoal grates with hot, soapy water, rinse well and dry. Lightly coat grates with
vegetable oil or vegetable oil spray.
!Clean inside and outside of grill by wiping off with a damp cloth. Apply a light coat of vegetable oil or vegetable
oil spray to the interior surface to prevent rusting. Do not coat charcoal grates or charcoal grates.
!If rust appears on the exterior surface of your grill, clean and buff the affected area with steel wool or fine grit
emery cloth. Touch-up with a good quality high-temperature resistant paint.
!Never apply paint to the interior surface. Rust spots on the interior surface can be buffed, cleaned, and then
lightly coated with vegetable oil or vegetable oil spray to minimize rusting.