Roadstar HIF-9997 TR User manual

Service Manual - HIF-9997TR
Service Manual - HIF-9997TR
R
HIF-9997 TR

REVISION SHEET
REV# BY DETAILS DATE
0 cbbyvox First release 2006-2-10
Model No.: HIF-9997TR TITLE: REVISION SHEET Revision No.: 0
Base Model: Nil Revision Date: 2006-02-10
- 1 -

INDEX
1.WARNING AND TECHNICAL SPECIFICATION 3
2.ALIGNMENT 4-6
3.BLOCK DIAGRAM 7-18
4.FUNCTION DIAGRAM 19-21
5.SPECIFICATION 22-23
6.VOLTAGE TABLE 24-26
7.TROUBLESHOOTING 27
8.DISASSEMBLY INSTRUCTION 28
9.EXPLOSION DIAGRAM AND BOM 29-32
10.WIRE ASSEMBLY DIAGRAM 33
11.PRINCIPLE DIAGRAM 34-35
12.REPAIR DIAGRAM 36-38
13.MATERIAL BILL OF APPLIANCE 39-44
Model No.: HIF-9997TR TITLE: INDEX Revision No.: 0
Base Model: Nil Revision Date: 2006-02-10
- 2 -

WARNING:
FOR CONTINUED SAFETY THE FOLLOWING PRECAUTIONS SHOULD BE FOLLOWED
DURING SERVICING.
1.MAKE SURE POWER CORD IS DISCONNECTED BEFORE REPLACING ANY PARTS.
2.REPLACE THE PRODUCT'S TYPE AND CRITICAL PARTS AS SHOWN IN THIS DIAGRAM.
3.THE FOLLOWING TEST MUST BE IMPLEMENTED AFTER EACH REPAIR BEFORE
RETURNING IT TO CUSTOMER. USE AN OHM-METER TO MEASURE THE F.C.
RESISTANCE FROM BOTH A.C. CONDUCTORS TO ANY EXPOSED METALLIC PART
SUCH AS A SCREW HEAD. METAL INLAYS ETC. THE RESISTANCE SHOULD
BE MEASURED 10 MEGAOHMS MINIMUM.
TECHNICAL SPECIFICATION
Power output :4.5 Watts RMS per channel NOTE:
into 4 ohms In keeping with our policy of continually
Frequency response :40Hz-16KHz improving our service and technical
Preset EQ :Flat quality of our products we reserve the right
:Rock to change component type, quality and
:Classic technical specification at any time.
:Pop
TUNER SECTION
FM Section :87.5MHz-108MHz
MW Section :522KHz-1620KHZ
CASSETTE SECTION
Tape :Cassette type
Tape Speed :4.76cm per second
Tracks :2Tracks stereo
Frequency Response :125Hz-8KHz
CD PLAYER SECTION
Frequency Response :40Hz-16KHz
S/N Ratio :60dB
Channel Separation :36dB
MODEL:HIF-9997TR (2Band 4.5W)
Revision No.: 0
Revision Date: 2006-02-10
Model No.: HIF-9997TR
Base Model: Nil TITLE: WARNING AND TECHNICAL
SPECIFICATION
- 3 -

Set the TUNER/BAND button to select AM.
Set the volume control to the reference output.
AM IF ALIGNMENT
Fashion loop of several turns of wire and radiate signal into antenna of receiver.
RADIO SETTING ADJUSTMENT REMARKS
465KHz Tune Scope across T102 Adjust the
400Hz (high end ) Speaker jack Wave for best &
Modulation 1620 KHz maximum output
NOTE: Repeat this adjustment of T102 for maximum and optimal output.
AW RF ALIGNMENT
SIGNAL RADIO SETTING ADJUSTMENT REMARKS
GENERATOR
522KHz Tune to 522KHz L105 VT=1.4V +/- 0.1V
400Hz (low end). SCOPE Across
Modulation Speaker Jack
1620KHz Tune to 1620KHz TC104 VT=7.8V +/- 0.1V
400Hz (high end). Probe with redwire(+)
Modulation the R136(R=100K)
612KHz 612KHz or R133(R=100K) L108 For maximum and
and probe the GND Good output
1404KHz 1404KHz with blak wire(-) TC103 For maximum and
Good output
Notes: 1.Repeat step 1 and 2 until their optimal outputs (1.4v and 7.8v) are obtained.
2.Repeat adjustment step 3.4.Three frequency station For Sen's≦64dB
Set the function to the tuner position and band switch to the FM position.
Conect Signal Generator across antenna terminals.
Set the volume control to the reference output.
Set the Balance control to center position.
FM IF ALIGNMENT
Fashion loop of several turns of wire and radiate signal into antenna of receiver.
RADIO SETTING ADJUSTMENT REMARKS
10.7KHz 87.5-108MHz Scope across T101 The "S" wave for
1000Hz Any point Speaker jack Best and maximum
Modulation
NOTE: Repeat this adjustment of T102 for maximum and optimal output.
AM SECTION
SIGNAL CONNECTION
Model No.: HIF-9997TR TITLE: ALIGNMENT PROCEDURES Revision No.: 0
Base Model: Nil Revision Date: 2006-02-10
GENERATOR
FM SECTION
SIGNAL CONNECTION
GENERATOR
CONNECTION
- 4 -

FM RF ALIGNMENT
SIGNAL RADIO
GENERATOR ADJUSTMENT REMARKS
87.5MHz TUNE Probe with redwire(+
)
L102 VT=2V +/- 0.1
1000Hz (low end ) the R101(R=47K)
modulation 87.5MHz or R102(R=47K)
108MHz 108MHz and probe the GND TC102 VT=7.8V +/-0.1
1000Hz (high end) with blak wire(-)
modulation
90MHz 90MHz VTVM&SCOPE L101 Adjust For maximum and
Across SPEAKER Good output
106MHz 106MHz Jack TC 101 Adjust For maximum and
Good output
Notes: 1.Repeat step 1 and 2 until their optimal outputs (2v and 7.8v) are obtained.
2.Repeat adjustment step 3.4.Three frequency station For Sen's≦26dB
CASSETTE SECTION:
Press the tape button.
Connect the SCOPE,VTVM,Distortion Meter and Frequency Counter.
ALIGNMENT Step Instrument connection Condition Adjustment
Speed 1Connect WOW and Flutter Play tape Adjust semi fixed
Adujstment Mcter Across the speaker jack with MTT-111(3KHz) Resistor VR901 for
8Ωload. 3 KHz +/- 30 Hz
Head 4Connect VTVM and Oscilloscope Play back test tape Adjust azimuth screw for
Adjustment Across speaker jack with 8Ωload MTT-113CN maximum output
(see diagram)
Oscillator 2Connect Frequency Counter T201 Record mode Adjust T201 for 52KHz
Frequency Secondary
Azimuth Adjustment Diagram: SCREWDRIVER
Base Model: Nil Revision Date: 2006-02-10
SETTING
Model No.: HIF-9997TR Revision No.: 0
TITLE: ALIGNMENT PROCEDURES
CONNECTION
- 5 -

CD PLAYER ADJUSTMENT
Press the CD button.
Connect the SCOPE across TRACKING, VREF,RFO points at PCB.
Alignment Step instrument connection Condition Adjustment
RF Adjustment 1Connect the scope CD Play in used stat
u
Adjust VR801
Across RFO point and the for maximum
Other across VREF point RF waveform
2Connect the scope CD Play in used stat
u
Adjust VR802
VREF Across RFO point and the For RF waveform,
And the other to VREF A=B
Point
3Connect the SCOPE across CD Play after TOC Adjust VR803
TE Balance Tracking and the other Display to 40-50MV below
To VREF point center baseline
for 20MV
Adjust as described below.
+probe for RFO at TA2065F(1) pinch
- probe for VREF at TA2065F(3) Pinch
VR 801:(RF)
+probe for TE at TA2065F(35) pinch
- probe for VREF at TA2065F(3) Pinch
VR 802:(EF)
+probe for TE at TA2065F(35) pinch
- probe for VREF at TA2065F(3) Pinch
VR803 :(TE)
Model No.: HIF-9997TR TITLE: ALIGNMENT PROCEDURES Revision No.: 0
Base Model: Nil Revision Date: 2006-02-10
- 6 -

Model No.: HIF-9997TR TITLE: BLOCK DIAGRAM Revision No.: 0
Base Model: Nil Revision Date: 2006-02-10
- 7 -

Model No.: HIF-9997TR TITLE: IC BLOCK DIAGRAM Revision No.: 0
Base Model: Nil Revision Date: 2006-02-10
- 8 -

Model No.: HIF-9997TR TITLE: IC BLOCK DIAGRAM Revision No.: 0
Base Model: Nil Revision Date: 2006-02-10
- 9 -