RoamAlert ECO User manual
ECO User Guide
© 2010 Stanley Security Solutions, Inc. All Rights Reserved. October 2010. 980-000009-000 Rev 04
Tel: USA: 800-824-2996 Canada: 866-559-6275 Int’l: +1 (613) 592-6997 Web: www.stanleyhealthcare.com
Stanley Security Solutions Stanley Healthcare Solutions Division 1550 N. 20th Circle, Lincoln, NE 68503
The Access Keypad
The Keypad provides four separate
functions:
• Local audible and visual alarms
• Bypass function to escort residents
through the protected exit
• Alarm reset when the Controller
is in continuous alarm mode or
resets the bypass sequence
• Controller status indication via
the LED indicators
The Controller may be bypassed or reset
at an exit point by entering a 3- to 7-digit
code at the keypad.
Status Indicator Condition Cause Action
Power OFF Power is o Turn Power ON
Solid Yellow Power ON, Ready Mode None; system ready
Bypass Flashing Green/Red + Beeping tone Bypass Mode Escort resident immediately
Alarm Flashing Red + Beeping tone Alarm Mode Investigate; reset alarm
Escorting Residents (Bypass)
1. Bring the resident to the exit, ensuring that he or she is not in the detection zone.
2. Enter the <BYPASS CODE> on the keypad.
3. Press <#> on the keypad.
4. Escort the resident through the exit.
Note: There are three automatic timers enabled by the system when the bypass function is activated:
• Bypass Timeout: You have 10 seconds to enter the detection zone after the bypass code is entered. If no
tag enters the zone within the 10-second period, the bypass is terminated.
• Transport: Once the tag enters the detection zone, you have 90 seconds to transport the resident through
the zone before the alarm is activated.
• Rearm: After the tag is through the zone or the door closes, the system automatically resets itself in 8 seconds.
Reset an Alarm
• Enter the <Reset Code> on the keypad and press <#>.
Clear or Correct an Entry
• To clear or correct an entry, press <*> on the keypad.
Power
(Yellow LED)
Bypass
(Green LED)
Alarm
(Red LED)
Clear Function Enter Function
2
RoamAlert ECO User Guide
Optional ANN6L Six-Zone Annunciator (AGEAN01-060, North America only)
Status
Indicator
Audible
Tone
Door
Status
Cause Action
Standby None Closed No tag in zone None required
Flashing
YELLOW
Warning
Tone
Closed Tag in zone 1. Investigate cause
2. Ensure resident safety
3. Reset panel
Flashing
RED
Alarm
Tone
Open Tag in or passing
through zone
1. Investigate cause
2. Ensure resident safety
3. Reset panel
Warranty
Stanley Healthcare Solutions’ RoamAlert ECO hardware is warranted against defects in materials and workmanship
and shall perform in accordance with published specifications for 1 year from the date of installation.
Stanley Healthcare Solutions’ warranty is limited solely to the repair or replacement of the defective part or product.
Stanley Healthcare Solutions reserves the right to change product specifications without notice.
Copyright Information
All content herein is the property of Stanley Black & Decker, Inc., its Affiliates, or their content suppliers and is protected
by United States and international copyright laws. The compilation of all content is likewise the exclusive property
of Stanley Black & Decker, Inc. (or the Affiliate identified in any copyright notice) and is protected by United States
and international copyright laws.
The trademarks, service marks and logos (the ‘Trademarks’) used and displayed in this publication are registered and
unregistered Trademarks of Stanley Black & Decker, Inc., its Affiliates and others. Nothing herein should be construed
as granting, by implication, estoppel or otherwise, any license or right to use any Trademark displayed herein without
the prior consent of the Trademark owner. Stanley and the Stanley design are two of the trademarks owned by Stanley
Black & Decker, Inc. and/or its Affiliates (“Stanley Black & Decker Trademarks”). Stanley Black & Decker Trademarks
may not be used in connection with any product or service that is not manufactured by or under license from Stanley
Black & Decker, Inc. or its appropriate Affiliate.
Zone Location
Up to 6 zones can be displayed on
the annunciator. These zones are
usually labelled during installation.
RESET Button
Silences an alarm, and resets the
system if the Reset Output is con-
nected to the Door Controllers. All
alarms in the system are reset.
(The system can only be reset if no
tags are in the detection zone).
Status Indicator
Adjacent to each identied zone
on the panel is a Status Indicator
that ashes either red or yellow to
provide a visual alarm.
Audible Alarm
Two distinct audible alarm tones are
generated when a tag enters the
detection zone ; one when the door
is open and the other when the door
is closed.
SILENCE Button
Silences the audible alarm, even
with a tag in the zone. The Status
Indicator continues to ash until the
alarm is investigated.
• To silence the audible alarm, press
<SILENCE>. Note: The audible
alarm is silenced, but the RED indi-
cator continues to flash.
• To reset the audible alarm, press
<RESET>. Note: The RESET button
only works if there are no tags in the
detection zone.
Other RoamAlert Keypad manuals
