Robe picklePATT ES User manual

1
User instructions
picklePATT ES
The picklePATT is a 100W lamp softlight housed in a sleek spun aluminium body which maximises its curves
to look as good on stage as the performers it illuminates.
Safety and operating instructions
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modication to the device.
Please consider that damages caused by manual modications to the device are not subject to warranty.
During the operation the housing becomes very hot (up to 100°C). Allow the device to cool
approximately 30 minutes prior to manipulate with it.
Min. distance from ammable materials to all exterior surfaces of the luminaire is 0.5m
Make sure that the available voltage is not higher than stated on the device.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the device and the pow-
er-cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it.
This device falls under protection class I and therefore must be earthed.
The electric connection, repairs and servicing must be carried out by a qualied employee.
During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily
mean that the device is defective.
Do not touch the device’s housing bare hands during its operation (housing becomes hot)!
For replacement use lamp of the same type and rating only.
Disconnect the device from mains before re-lamping or any maintenance/cleaning operations. Allow to cool
cca 30 minutes.
CAUTION ! EYE DAMAGES !
Avoid looking directly into the light source
This device was designed for indoor use only.
This device is for professional use only. It is not for household use.

When choosing the installation spot, please make sure that the device is not exposed to extreme heat, moisture
or dust !
The device never must be covered with cloth or other materials during its operation.
The minimum distance between light output of the and the illuminated surface must be more than 1.5 meters.
Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fastened.
The maximum ambient temperature 45°C must never be exceeded.
Technical specications
Mains input: 250V max
Frequency: 50-60Hz
Max. power consumption: 100W
Lamp socket: E 27
Cooling: convection
Max. Surface temperature: 100°C
Min. distance from ammable materials: 0.5 m
Min. distance to alight object: 1.5 m
Max. ambient operating temperature: 45°C
Weight: 5kg
Beam angle: 55°(@1/2 beam), 102° (@1/10 beam)
Mounting Points: Mounting horizontally or vertically via mounting yoke
(360° tilt range)
Rigging: M12 mounting for clamp or spigot.
Operation position: any
Dimensions (mm):
2

Beam distribution (100W lamp):
Installing the xture
The xture has to be rigged to the truss or fastened to the oor stand via the mounting yoke only. The hole of
diameter of 12.2 mm in the yoke serves for screwing the yoke to the clamp or to the spigot (the spigot has to
be inserted into oor stand and secured).
Always check that the xture is installed safely without a possibility to tilt it over.
Installing the lamp
Unplug from mains before installing the lamp!
Allow the device to cool approximately 30 minutes prior to manipulate with it
1. Unscrew four securing screws (1) and remove the front sieve cover (2).
2. Unscrew the lamp (3) from the socket (4).
3. Screw the new lamp to socket.
Make sure that the lamp is installed tightly into the lamp socket. Do not install a lamp with a higher wattage
than stated in technical specications of the xture.
5. Place the front sieve cover (2) and screw the four screws (1).
3

4
Version 1.0 May 25, 2016
Specications are subject to change without notice.
Optional accessories
Floor Stand for PATT 2013 (P/N 1098 0259)
Spigot for PATT 2013 (P/N 1098 0260)
Tripod for PATT, RoboSpot, LightMaster (P/N 10980350)
Tripod ( P/N 10980287) - For Domestic use only! No Commercial Warranties ! Made for use with PicklePATT
only !