ROBOfiber RB-EXTGE-104H User manual

4 www.robofiber.com
RB-EXTGE-104H Gigabit Power-over-Ethernet Extender
Maximum Distance Reach for Power Sources
Multiple PoE Extenders can be connected every 100 meters to obtain
greater distances. The actual figures depend on operating conditions.
The range mentioned is for cables 24 AWG or heavier Cat-5e or Cat-6
cable except where specified.
Examples for medium power PoE Devices (that are PoE Class 2, or
require under 6 watts)
PoE Source
PoE switch
(802.3af, output
voltage 50V)
15W mid-span
(802.3af, output
voltage 50V)
PoE+ switch
(802.3at, output
voltage 50V)
30W mid-span
(802.3at, output
voltage 50V)
Maximum Distances
300m
300m
400m
400m
Examples for full power PoE Devices (that are PoE Class 0 or 3, or
require under 12 watts)
PoE Source
PoE switch
(802.3af, output
voltage 50V)
15W mid-span
(802.3af, output
voltage 50V)
PoE+ switch
(802.3at, output
voltage 50V)
30W mid-span
(802.3at, output
voltage 50V)
Maximum Distances
200m
200m
300m
300m
Examples for PoE+ Devices (that are PoE Class 4, under 22 watts or
802.3at compliant)
PoE Source
PoE switch
(802.3af, output
voltage 50V)
15W mid-span
(802.3af, output
voltage 50V)
PoE+ switch
(802.3at, output
voltage 50V)
30W mid-span
(802.3at, output
voltage 50V)
Maximum Distances
Not applicable
Not applicable
200m
200m
Gigabit PoE Extender
IP52 outdoor rated
RB-EXTGE-104H
User Manual

2 3
RB-EXTGE-104H Gigabit Power-over-Ethernet Extender
RB-EXTGE-104H Gigabit Power-over-Ethernet Extender
Gigabit Power-over-Ethernet Extender
Order Information
RB-EXTGE-104H - Gigabit PoE Extender 1(PoE IN) into 4(PoE OUT)
Description
Both Ethernet and PoE UTP connections have cable distance restrictions
to 100 meters only between network ports. To overcome this limitation,
the RB-EXTGE-102H was developed: an in-line PoE Extender working on
both Cat-5e or Cat-6 cables.
With the RB-EXTGE-104H PoE Extender, PDs (such as IP Security Cameras,
wireless access points) can be installed at greater distances. By
connecting the PoE Extender for each 100 meters of cable, both Ethernet
and PoE signals double the reach, all depending on PDs power
requirements and capacity of the power source equipment (PSE).
The PoE Extender does not require any additional power supply and the
connected PD is fed by a single PoE switch port or injector. RB-EXTGE-
104H offers four Gigabit Ethernet ports, which are all configured
automatically for link speed, duplex and auto direct/crossover
negotiation and connectivity. When connecting to a PoE Switch, the
extender supports PoE class 0,2,3 and 4 output. The total PoE power
delivered can reach 54w (PoE Switch needs to provide IEEE802.3bt power)
Features
•Compatible with IEEE802.3af and IEEE802.3at PoE standards for PSE
•Compatible with IEEE 802.3af/at/bt as a PD device
•Extends range of PoE and Gigabit Ethernet to an additional 100 meters
No additional power supply is required
•Automatically detects and protects PoE equipment (PD and PSE) from
being damaged by incorrect installation
•Gigabit full-rate network throughput
•Wall-Mountable design
•Outdoor ready with IP52 rating
•Easy plug-and-play installation
Technical Specifications
No. of Channels
1 PoE IN port and 4 PoE OUT ports
Pass Through Data Rates
10/100/1000 Mbps half/full duplex
PoE Input
Pin Assignment and Polarity: Both 1/2 (-), 3/6 (+)
and 7/8 (-), 4/5 (+), IEEE 802.3af/at/bt compatible
PoE Output
Pin Assignment and Polarity: 1/2 (+), 3/6 (-), Output
Power: up to 30W for one port or 13W each when 4
ports are used
Connectors
Shielded RJ-45, EIA 568A and 568B
Network Cable Type
Outdoor type Shielded category 5 (or higher)
Dimensions
185mm x 85mm x 40mm
Mounting
Wall or shelf
Environmental Conditions
Operating Ambient Temperature: -20 to 55℃
Operating Humidity: Maximum 90%, Non-
condensing
Storage Temperature: -30 to 70℃
Storage Humidity: Maximum 95%, Non-condensing
Indoor and Outdoor operating device
PoE compliance
IEEE 802.3af (PoE), IEEE 802.3at (PoE+), PD IEEE
802.3bt
Application Diagram