Robotouch RBT13 User manual

robot*uch.
RBTl 3
Quattro Multi-purpose ConversionTreadmill
t

Your choice of our product is sinc;rrrcly ;rlrprlr t,tlt'rl
be sure to read the specification carr-'[trlly
Corrtorrls
Warning, contents, main tcr;lrtttr:;rl p.l,rtrrr'lrt
Brief introduction.
Assembly illustration
Assembly illustration detrrrl:;
lnstallation Steps..
Methods:
O MotorPower:2060W
O Speed Range of operation: 1.0- 16 (km/h)
O Slope adjustable range: 0-15%
a Display for Time Range: 0. 00-99.59 (m:s)
O Display for Distance Range: 0. 00-99.9 (km)
O Heart Rate Range: 50-200 (time/minute)
O Display for Calorie Range: 0-999 (calorie)
O Total area: 210x81x134cm
O Available using area: 138 x 46cm
O Weight load: 125k9
Features
X 2060W low-noise motor;
X Speed range: 1-16 Km/H;
X Electric adjustment inclinations: 0-15%:
X User-oriented shutdown functions with choices of emergency stop and
slow stoP;
X 7-inch orange back-light LCD displayer with 8 intelligent treading
programs;
X Attached with high-sensitive hand-held hearGrate calculation hand-bar
with electronic hand-bar speed adjustment/inclination adjustment
functions:
X Hydraulic folding locking device;
X Large-power Hi-fi stereo system with MP3 audio input;
X lntelligent green negative ion generator;
X New 3-in-1 super anti-shock system (spiral spring anti-shock + silicon
gel shock pad + pu castor )
X Ergonomic sit-up, massage, waist-twisting functions.
ll. Brief introduction
please
..'.,1
..2
...3
.4
.,1
ti
.11 I :)
Electronic Meter Display irrrd
Usage and Safety Protection
lmportant Note
Repair and maintenance.
General troubleshooting
Exercise lmportant Note.
I tttrt;lion ()l)(,r;llr)l
of tlrc I rcirtirrrill.
l;i
1t)
l8
l. Warning, contents, main technical parameter
Warning!
1.When you are using the machine to exercise, please do not let your children (kids,
infants) approach the machine, and minors must accompany with adult' s protection
to avoid being hurt when using.
2.Before using the machine to exercise, please clasp the safe ty switch to the clothes
in front of the chest that you can touch omnivorously.
3.The power of the machine should be well grounded. After cxcrcising and stopping
using the machine, please switch off the power.
4.To avoid unnecessary trouble, do not open the fronl r;ovcr ol llrr: treadmill and the
electric controller of the adjusted machine cxccpI lirr llrt: ptolr::;:;iottal personnel.
5.For the purpose of your safety and the treadntill rjLtrrliorr, il i:; lorbidden for the
overweighed persons to use the treadmill or uscrl by lwo lrcr;orrl irt lhe same time.
6.For the purpose of your safety, do not gct on Ilro lrcirrlrrrill lrorn llrc backside during
the operation of the treadmill.
7.Do not touch the running belt during the operatiorr ol ltlr: lro;rrlrrrill attd do not run
on bare foot.
B.The patients with high blood pressure or heart tiisc;r;c slrorrlrl rrot use the
treadmill alone.
For the health and safety of you and your f ittrtrly, ltolottt ltrot;ctttiing
the normal exercise, please read tht-'fttllowitrtl ittl;ltttt:liolt ilnd
notice, to get yourself more fun from the sJrorts t ll' r' prolrihited
to adjust the controller of the machine exo(rl)t lttt llto ;trofo:;sional
personnel.)
Please note that this product has weight restriction. lt rnay ;rllccl llro lrlr: l;pirn of the
treadmill, if yourweightover 125 kg (275 lbs),
Main Technical Parameters
O lnput Power Voltage: AC220V-240V (50*60H2)
O Environmental Temperature: 0C -40"C
a Current:11.5A

lll. Assembly illustration
Go
---9 A .i
-------J9 --\;l
[-f._f7
u\
@-fuad
6 \9J
!o/------ro o
J
lV . Assembly illustration
tb, Nane Anpunt No. Mme Amunt No. llame Amun
Eledrcnic meter I20 olenoao
nmledor mPLJ whed 2
2Safety $/itdr 2\ Wringclp (large
size) 4l:)
M8x 45 pan hea(
tE)€gon socket
scE\16 2
3Lef{Rigtl hoHing
md Apiece 22 Rtbber pd 241
l,il8x70 Cdurm
head he)€gon
socket 2
4Flghtfoot boot 23 50x 25 tub
sbpper 2atcar aopflng
case (ldt)
5Ldt footboot 24 LtTIng eEqrE
trntor 43 rear aqp$ng
case (righ)
6Bottan franE 2li/6'45smk scrs 644 Rear rcller I
"1
ul1 0 x 16 pan fEar
heEgon socket
ssews t2 26 22hdl bet 6Ruming board 1
8
vl1 0 x 55 pan tEa(
he)cgon $cket
sclews 427 Shck pad 4,16 Runring blt 1
9O!0lat strim 30 28 Front roler l$n-slp drip (left
l0 Rubber bot pd 4Slicon gel pad 448 Sije {rip
ll Ml0 x 50pan tEa( he)€gon socket
smws 230 Midle crossba
weldirg 149 Non-slip strip
(rish)
t2 o73[egwheel 23t Ai spting I50 M6sge head
l3 Bottomframeleg
vfieel cor'er 232 Ar strhg $edh I5l Upper orvetube
l4 vl1 0 Non bose nu IFolding anti-shod
deve 452 MBx @ pan hea(
tE)€gon socket
15 Eedricmobr
coEr 34 tn tt M6sage head
hdder I
t6 TrarsfcrrEr 35 Runnhg rack
co/er il M8x 16 panheac
tE)€gon socket
scre\r6 l
17 E€ctricalccrltrol 136 rc oo\ier 256 Fofl @wr 4
l8 llbtor Cunent: I37 $dng locatirg
rirg 856 F25 roJnd ube
cov€r 4
l9 lvlono switch 138 9dns 4M8x 50 panhea(
lE)(agon socket
scres 2
V. Installation StePs
Before the shipment, the different parts of the treadmill have been strictly checked
and debugged. Therefore, the treadmillcould be installed according to the following
steps.
Stepl:Openthepackageandtakeout connectoratthebottomofuprightpole )
the treadmill. lnsert left upright pole ( no into bottom framework, lock them up with 2
4

.sopts qloq uo sleqsE/vr lElJ
qilm pue /v\elcs lolcos uooexoq peoq ued
0L*81 1 lql!/r^ eqnl e^Jno reddn uo lt lcol
ueql 'sspts qloq uo sroqsE/v\ IBI q]!/il pue
s^ elcs lelcos uooexaq peer.l ued ogigu\l
z qlt/v\ lJol euerJ ulolloq uo lcet eql xu
pue 'lcBJ peoq eoBsseu lno elEl :g dels
'spJen6 pupq Jo alpptrrr oql ut sl lcel
6urpeell ieqleq/v\ tuJlJuoc pue ,IceJ
6urpee.r1 plog '6n1 durnf-rgue 6ur1co1
ro1 iv\ercs g*9I11 eql esoo; :7 delg
s
.sJaqse/v\ cte pue s/neJcs
1elcos uo6exeq peeq ued OZr+gy\ Z qy/r^
e;od lq6udn uo lt Icol puE a^eols ql!/r^
re^oc 'eqnl o^rns JOddn lno olBl :g de15
peeq ued gl,0ll l z pue,sroqsP/v\
lel1 pue s/y\oJos 1a1cos uoEexeq peeq ued
9r*0ly\l 9 r.llliv\ lcBr laleu xll .da1s qpno;
eql reUV 'eJod 1q6udn olur 6n; lcer Jeleut
liosut :alod lqEr.rdn 1q6r: pue Jeleu ctuojlcola
Jo sel!/v\ eJoc uleu eql lcauuoc :e dels
Ields;p suotlcunJ pue Jelel l oruoJlcols Jo crqdel6 eq1 .1
uolleJedO uotJounl puE ^EldstO Jeley\l ctuotlcelf .ln
'ece1d tedo.rd ol eurq3Btu eq;6urnotl se uoos
se llrulp'oJl aql asn uec noI ,lcoqc lolJv . ( .(acueueluteu pue rredet,, laldeqc ees
'6u;ppr1s ou pue eprs }q6u ol se^ou 11eq 6uruunr) i{1e,do.rd sr 1;eq 6uruunJ Jo sseurq6!r
1o eel6ep Jotllor.l^ ,olqlxelJ 6uruunl Joqloq/v\ 1;eq 6uruun: 1o slled qcBo lceqc
pue 'ualsel raqloq/v\ autqceu aql ]o sluauoduJoc qcee i(11n;a.rec lceqc espold :g dols
'uo lleq a6essBr.r.r eceld .sJotlsE/v\ puE s/v\eJcs le1cos uo6exeq
peeq ued gt-gy\l e qlt/v\ IceJ peeq e6esseu uo ueql xtl ,peeq eEesseul lno o)iel :1 delg
's/v\oJcs
ssecer ssorc peoq qunql 6!q g.ryrl
7 qlrm dn slooq 1q6udn eql lcol ,Icer
Jolaul Jo spten6 pueq Jo alpptu eql
le petuJtluoc st IceJ 6urpeeil la11y
'sde1s qllno; pue prlql aql lcnpuoc
I11s.ll3 's1ooq alod 1q6r.rdn 1q6;r pue
llel qlliv\ selod gqDlrdn leno3 :7 delg
(.dn smelcs lcoueql ,sp.ren6 pueq
,o olpplut aql sl lcer Eurpeerl pue dels q1rno1
aql JoIJV 'da1s srql ut s/v\eJcs qlrn dn )col lou
op esEeld) 'sJoqsE/v\ telJ pue si eJcs lalsos
uo6exaqpeeq ued 99,g1y1 7 qym dn uoql lcol
pue 's.toqse/v\ lelJ pue siv\eJcs 1e1cos uo6exeq
'sJoqse/v\ lelJ pup s/v\oJcs lalcos uoDexeq peeq
uEd gLi0!y! Z rllt/r^ lcol ,Iro/ilaurerl ulolloq olu!
elod eq1 l.lesut 'IJo/\ ouleJJ uolloq Jo eJll aql
qlin (e1od 1q6udn jo uolloq oql te rolcauuoc
) alod 1q6udn lqbr.r lceuuoc ueql .sroqse/v\
lell puB s/v\elcs ;e1cos uo6exaq peeq ued
99*0 ly1 qlrm dn ureql lcol pue .sreqse/$ lelJ
pue s/v\ercs lelcos uoEexaq peeq ued gl+Ot,yV
L

2. Electronic meter window
1. "Speed" window: During operation, it displays the speed value that time,
and the needle points to some speed: 1.0*16KM/H.
2. "TIME/PULSH" window: Display exercise miles and heart rate.
3. " DIS/CAL/INCL" wlndow: Values will be displayed alternatively every 5
seconds; Display exercise distance. Display exerciser caloric consumption;
Display inclination.
4. " m "lcon:Displayvoicemute.
t. " l@l orofl!t!l[ ,, lcon:Displayvoice start.
/-:I
6. ' \=J " lcon: Display manual mode.
7. " ffi " l"on: Display time count down mode.
8. " m " lcon: Display distance count down mode.
9. " m " lcon: Display calorie count down mode.
10.'B " lcon: Display program mode.
ak-
11. ' 1186 " lcon: Display fan start.
3. lnstruction for Keys
1. " Program" is program key: Press PROGRAM key to select B inner
program "0, 00" , "P1-.''P8" in standby mode. Manual mode is the default,
mode of the system with the default speed of 1.0 KM/H. ( "0: 00" is manual
mode and P1 P6 is inner program. )
2. "Mode" button is mode selection key: Pressing the button could circularly
select "0, 00", "15r 00", "1.0" , "5O" . ( "0' 00" is manual mode,
15: 00" is time countdown mode, " 1.0" is distance countdown mode, and "
50" is calorie countdown mode.) When selecting the mode, speed up/down button
could be used to set related countdown value.
3. "Start (ON) " button is start key: After the setting,
button could initiate the treadmill.
4. "Stop" button is stop key: During the exercise, the
stop the operation of treadmill and reset the system.
5.Accelerationkey and deceleration key to add or reduce the speed: At standby
status, it can adjust the value. When the treadmill is initiated, it could used to
adjust the speed with the range of 0. 1 kml time. lf pressing it over 0.5 second,
the speed will automatically increase ordecrease.
6. "3,6,9,'l 2,15" is hot key of speed. When the treadmill is initiated, it could
used to adjust the speed.
7 . " lncline+" , " lncline-" are the keys for the increase and decrease of
inclinations: on standby, it could adjust set value. When the treadmill is initiated,
it could used to adjust the inclination by the range of 1o/o. lt pressing it over 0.5
second, the speed will automatically increase or decrease steadily.
8. '3%, 6%, 9%, 12%, 15%" is hot key of inclination. When the treadmill is
initiated, it could used to adjust the inclination with "lncline +" "lncline -" .
9. "+" . "-" are the keys to adjust the volume.
10. " x fan" is the switch for fan: press this key to switch the fan on or off.
4. lnstruction for operation use
4.lAfterturningonthepower,thetreadmill givesoutasoundlike "Bi"'Bi" lnsert
safety switch into standby mode.
4.2 At standby status, pressing "start (on)" button could start up the treadmill.
Manual mode is the default operation mode of the system with the default speed of
1KM/H (the window display 3-2-1).The speed can be set by pressing speed up/down
button or Speed hot key "SPEED +/-" can adjust the running speed of treadmill
(1-16 KmlH), or press speed hot key 3Km/H; 6Km,/H; 9KmHl: l2Km/H:
i5Km/H. The inclination can be set by pressing "Inclinedown/up" (O%-15%)or
INCLINE hot key " lncline +/-" can adjust the inclination, or press INCLINE hot
key 3%,6%,9%, t2%, 15%.
4.3. Under running mode, pressing Stop key can stop the machine.
4.4 Under running mode, pull safety switch if you have an accident, pressing STOP
key (lower right corner of the red button) can stop the machine.
4.5 You can choose circle mode under standby mode: exercise caloric consumption
countdown, the exercise time countdown and the exercise miles countdown. Press "
acceleration and deceleration" key or "up and down" incline key to adjust the
time, exercise distance and caloric consumption. After setting the values, press
"start (on)" key to start treadmill.
4.6 On standby, pressing " program" button could circularly select 8 styles
operation programs from manual mode to "0, 00" , " Pl-"' P8"' FAT" "
0:00" is Manual mode and P1-P8 is inner program. After selecting program
then press start to start the machine.
5. lnstruction for the Function
5.1. - Turn on the switch and make the magnetic secure lock to be absorbed
into the position of the secure lock under the panel.
5.2. - on standby: Press the "start" button and the system comes into 3-
second countdown and the buzzer gives out a sound. The SPEED window displays
the countdown. After the 3-second countdown, the treadmill begins to operate
at the speed of 1 km/h (This is manual mode). When the treadmill is started,
the speed can be adjusted with speed up/down button or press speed hot key
directly. The inclination can be adjusted with " lncline up/down button or press "
lncline" hot key directly. The time window displays positive count varies from
0.00-99.9. When the time of operation exceeds 99 minutes and 59 seconds,
the system will stop automatically.
5.3 - on standby: Press "mode" button to enter into time countdown. The
"time" window displays "15:00" and flickers. The time of exercise can be
set by pressing the "speed up/down" button or " "lncline upldown" key with
the range from 5:00 to 99:00. After the setting, press the start button. The
treadmill will begin to run after 3 seconds delay. The speed can be set by pressing
speed up/down button/Speed hot key. The inclinations can be set by pressing incline
up/down button/incline hot key; Press the stop button, and the treadmill stops. Time
pressing the start (ON)
button could be used to

countdown will turn zero after the overflow and take account positively. For
countdown, it will turn from setting value to zero. When it turns to zero, treadmill will
stop smoothly and display "End". After full stop, it enters standby status.
5.4 - on standby: Press "mode" butlon to enter into distance countdown.
The distance window displays "1.0" and flickers. The distance of exercise can
be set by pressing the speed up/down or incline up/down button with the range
from 0.5 to 99.9. After the setting, press the start button. The treadmill will begin to
run after 3 seconds delay. The speed can be set by pressing speed up/down
button/Speed hot key; press the stop button, and the treadmill stops. Distance
countdown will turn zero after the overflow and take account positively. For
countdown, it will turn from setting value to zero. When it turns to zero,
treadmill will stop smoothly and display ' End" After full stop, it enters
standby status.
5.5 - on standby: Press " mode" button '3 times to enter into calorie
countdown. The "calorie" window displays "50" and flickers. The calorie of
exercise can be set by pressing the speed up,/down or incline up,/down button
with the range from 10 to 999. After the setting, press the start button. The treadmill
will begin to run after 3 seconds delay. The speed can be set by pressing speed
up/down or incline up/down button/speed hot key; press the stop button, and the
treadmill stops. Calorie countdown will turn zero after the overflow and take account
positively. For countdown, it will turn from setting value to zero. When it turns to
zero,treadmill will stop smoothly and display " End" After full stop, it enters
standby status.
6. Each value of range in windows:
!{alue of setup lnitid Vahe
Time (mhute:
..i^..r o:oo
lnltial setting vatue
l5:00
Setthg Range
5:OO-SS:m
Display Range
0 : 00 -99:59
Speed (KM/H) i. o1.0 1.0-t4 1.0-16
Distance (Km) 01.0 0, 5-99. 90.00-99. I
Heart Ete
ftimrc/min\ Pri/A N,/A 50-200
Calorie (kcaD
rise
0
0
m
0
10-999
o-12%
0 -999
0-15%
7. Program Mode
The system has I inner programs from P1-P8. Press "PROGRAM" key to select
customize program "p1-p8" in distance mode. The "time" window displays "
10: 00" and flickers. The time of exercise can be set by pressing the " speed
up/down" or " incline up/down" button with the range from 5 to 9 minutes.
Press the "start" button to start inner program, lnner program can be divided
into 20 segment, exercise time of each segment = setting time/2O.When coming
into the next stage, the system gives oul 3 sounds like B i-B i- B i. The speed of the
system is changed with the difference stages of program. During this time, the
speed/incline can be changed by pressing speed up/down or pressing incline
upldown button. But when the program comes into the next stage, the speed is
resumed in accordance with the stage. When a program is finished, the system
gives out " B i-B i- B l" sounds. At this time the treadmill will be reset by
pressing stop button and re-enter into the status ofstandby. . ,
Programme illuminate: P1: aerobic slimming exercise; P2: mild anaerobic road
running; P3 : mild anaerobic meadow running; P4: mild anaerobic mountain
running; P5: mountain contest; P6: Road contest; P7': physical test; P8: cross
country running
Appendix 1 : P1-PB program exercise chart
Seltine/2o lme phEses=operation time of Fevious and nexlline phases
irod. I2 3 .l s 6 1t9l0 11 t2 13 14 l5 l6 l7 l8 t9
ISpeed 3 1 576 3 75{6 3 6 1 T 3
3433 3 3 33{2
2
Spaed I35t32s1{6E3 6 .l 18163
rtbr t332{3 3 3 {5 3 .l 53.l 3I
3Speed t0t2 7.t 3112 tI65t2 I1
nclhalbr ,3{3I3{s6 7 I9l0 a6{
ISpecd 215 9 1379.l 63 9 5 7 5 3 3 {3
nclhatbr 2{6tl0 I I 6 6 {{3{565.l 3I
5Speed tt2 2I6t2 {36 5 7 t{I
3I3{67tIE6{3 3 3J
6Speed t2 1 6 t2 7 6 {6l2 62{I
3{63 3 d 5{ { J32I
1Speed 6t10 12 t'I I,l t12 t2 10 t6"l 332I
3 ! ,l 3I33I3I
ESpecd 2tlo 59t2 t2 10 E6 6 I10 113I
3{3{563I2. I61E{3I
8. Safety Lock function:
ln any status, pull Safety Lock if you have an accident, the treadmill will stop
running urgently. lt displays " and the alarm sound like " BB" , The
treadmill can' t process any operation. Re-fix the Safety key and the treadmill enter
into initial mode. The window display the previous setting and the equipment reset.
Button instructions are to be inputted.
ln any status, pull Safety Lock (Lower right corner of the red button right) if you
have an accident, the treadmill will stop running urgently. lt displays " - - - " and
the alarm sound like "BB" . The treadmill can't process any operation. Re*fix
the Safety key and the treadmill enter into initial mode. The window display the
previous setting and the equipment reset. Button instructions are to be inputted.
l0

9. Sleep Mode Function
The system is provided with power saving function. lf no button instructions are
input within 10 minutes at standby status, it will enter the power saving mode and
displays will automatically shut down. The system can be restarted by pressing any
button.
1 0. Heart rate calculator function :
The heart rate is for reference, which can not be used in medicine. When testing,
both hands should grip tne seni l minutes.
tL [aftlglglgn:
when the power is on and it is connected with Mp3 or other audio equipments,
electronic meter could play music. And could control the volume. Please note that
the volume should be under control in case of the influence on the quality of sound
and built-in audio circuit.
12. Shut down:
You could switch off the treadmill at any time by shut down the
power. And it will not damage the treadmill.
Vll. Usage and Safety Protection of the Treadmill
1 . Adjustment of the Treadmill
1 .'l . After installation, put the safety switch to the position of the electronic meter.
1.2. Before accessing to power, please check whether the voltage of the power
supply is appropriate and the ground wire is well grounded. Hand-dragging the
running belt, check to see whether it rotates smoothly and without strange sound.
1.3. connect the electrical plug; turn on the power lock, all the windows of the
electronic meter will display initial value while the running belt remains still.
1.4. Press "onloff" key, run the treadmill in low speed with 1 km,/h and check
to see if the treadmill and electronic meter operate normally.
1.5. Press acceleration key, deceleration key, ascend slope key and drop slope key
to check if the adjustment works well.
1.6. Press the "sroP" key to stop the treadmill. cut off the powerand remove
the electrical plug.
2. lnstruction of the Operation Use
The electric treadmill can be used after the installation and adjustment:
2.1 . Plug in the jack wilh 22oY-240v power voltage for home use; the power jack
must be well grounded.
2.2. lnsert the safety switch and press the'srART" key. The running belt moves
slowly, the speed is about 1 km/h and the electronic meterdisplays the speed per
hour.
2.3. lf increasing the speed of the treadmill, you can press the acceleration key. The
speed will upgrade per sound from the buzzer, and the Maximum speed is 16 Km,i h.
2.4 Press "incline + " button to increase the inclination of the treadmill. one
sound of " B" of the buzzer indicates one phase increase. The maximum
inclination is 15%.
2.5. lf there is no time for deceleration with rapid running, you can pull out the safety
'l .1 . The line for power supply must not be used for other electrical equipments on the
same line with the treadmill. And the current provided for the treadmili must exceed
11 .5 A.
1.2. The nominal voltage should be in the range of AC 220V-240V. The voltage
over this range may lead to the abnormal running of the treadmill.
Lock, and the treadmillwill immediately stop.
2.6. when finishing exercise, decelerate the running speed and then press the srop
key to stop the treadmill slowly.
2.7 Folding and unfolding steps: before folding the treadmill, you must reset and stop
it, switch it off and then fold it. Remove the front plug. Make sure that locking hook is
in place, then move or leave the treadmill. Before unfolding it, you should stand on
air spring sheath, loose air spring hook rest. As following picture:
3. The Safety Protection of the Treadmill
3.1. ln any emergent situation, the treadmill will stop running as soon as the safety
switch is pulled out or press emergency stop key. so when you are doing exercise,
clasp the safety lock to the clothes in the proper position. Make sure safety for using
this machine.
3.2. lf skidding of the running belt takes place or the running belt is blocked, the
motor will turn off automatically in 5 seconds.
Vlll. lmportant Note
1. Power Source
1"1 . The line for power supply must not be used for other electrical equipments on the
same line with the treadmill. And the current provided for the treadmill must exceed
11.5 A.
1.2.the nominal voltage should be in the range ot AC 22OV-240V. The voltage
over this range may lead to the abnormal running of the treadmill.
1 ,3. Timely plug out the power supply after usage.
1 .4. ln the winter, keep the humidity inside to some extent in order to avoid the strong
static electricity.
1.5. Replace or purchase the power cable from the authorized dealers after the power
cable was damaged.
2. The Environment for Placing
2.1. Better to place the treadmill inside to avoid humidity. lt is not permitted to splash
water on the treadmill, and also it is not allowed to place other subjects on the
treadmill.
2.2. During the operation of the treadmill, motor will produce a litfle spark, and
\
11 t2

therefore it should be placed with good ventilation and be isolated from explosive
substances.
2.3. When using the treadmill, keep the fourfeet mats and two rearwheels of the
treadmill stably on the ground. lf the ground is not smooth, use carpet or rubber
board to fill up.
2.4. ln daily life, keep the house clean in order to reduce the dust inside because
the dust will cling to the electronic components to affect the sensitivity.
3. Attention before and during the Exercise
3.1. Put on suitable sports wear and shoes for safety when running. lt is prohibited
to run on the treadmill on bare foot.
3.2. lt is not permitted for two persons to do exercise at the same time.
3.3. Prepare a piece of towel for sweating in order to avoid the damage of the
electronic parts inside the treadmill caused by the sweat dropped on the running
belt and swung into the machine.
3.4. First learner should put one foot on the running belt and try several times
standing on the side. Do exercise on the machine after following the speed of
treadmill.
3.5. This treadmill provides enough power for still starting in principle. ln order to
prolong the lifespan of the treadmill, however, it is suggested that you stand first on
the sides. Wait until the treadmillworks normally and then do exercise.
3.6. lt is prohibited to stand on the treadmillfrom the back end to avoid tumble.
3.7. Grab the handles with even force and run in middle of the treadmill to
avoid the running belt moves to the sides.
3.8. When coming into normal status, it is suggested that you keep hands off the
handles and swing your arms naturally, which will have better exercising effect.
3.9. Press stop key when getting down the running belt. Do get down when the
running belt completely stop.
3.10. Keep the children off the running treadmill to avoid nipping the hands or
clothes by the running belt to hurt children.
3.11. lt is prohibited to touch the running belt and the running wheels during
operation.
4. Additional Attention
4.1 . Heart patients are not suggested using the electric treadmill alone.
4.2. Decide the running speed according to your body status; Patients are
suggested not using or using under the doctor's guide.
4.3. Heart rate sensor is not belonged to medical equipment, and the metrical
result is just for reference.
lX. Repair and maintenance
Please pay attention to the following issues when you are using the
treadmill.
1. Keep treadmill clean
1.1. Keeping treadmill clean could fairly prolong life-span of treadmill. Please
frequently clean the exposed running board and footplate along both sides of
running belt to avoid the long-term accumulation of dust and dirt.
1.2. Running belt could be cleaned with soft cloth dipped with soap water. Try to
avoid the water to flow under running belt and into protection case.
1.3. Check the bolts and screw caps of the treadmill periodically. lf something
looses, please lock and fasten them immediately with tools.
1.4. Please check whether clean in the motor belt. Please clear up all remoras for
avoid unnecessary shake while using.
1.5. Regular to clean electronic control system and the dust surrounded motor and
make sue that the treadmill run normally.
2. Lubrication
2.1. Please spread the Lubrication for the running board with the attached
lubricating oil to reduce the frictional reciprocally between the running belt and
running board with the high temperature to damage the running belt, running
board and the load of elector motor. (Note: lt is not suitable for the children
to play with, avoiding eating inadvertently. )
After a period of use of treadmill, it is a must to lubricate running board and belt
with professional lubricant. ln terms of various operation period and intervals of
lubrication, it is referred to as follows:
Opeatbn period of treadmil lntervals of Ubrication
Operde less than 3 horrs per veek Lubricde orce per 3 months
Operab 36 hours perweek Lubricate cnce per mmth
Opeate more than 6 hotrs per veek Lrbricate once per 10 days
2.3 The way to lubricate: loose left and right adjusting bolts at the back of
treadmill with professional devices. Raise running belt by 10-15cm. Pour
adequate professional lubricate onto running board and even up. Tighten
running belt up. (See details of adjusting way in Adjusting way of running
belt) Don' t overuse lubricate. Please remember: rational lubrication is vital to
life-span of treadmill.
3. Judgment of resistance:
Uncleanness or lack of lubricate will both lead to more resistance between
running boards, which may do damage to electric engine and control board.
lndications of much resistance are as follows:
3.1 When power-off, running belt is hard to move or doesn' t move;
3.2 When treadmill operates with load at medium speed, if you turn off the
security switch, treadmill stops immediately;
3.3 More resistance may lead to the damage of electric engine or control board,
short circuit, tripping, fuse blowing, etc.
4. Tightness adjustment of running belt:
4.1 Although running belt of every treadmill has been adjusted before release
and assembly, it will turn slack after a period of use. Maintenance will rely on user
himself. lf running belt is very slack, it will skid between running belt and roller
when standing on belt. While the belt is too tight, it may damage electric engine,
running belt and roller, etc. Commonly, both sides of running belt part from
running board by 5-6 cm.
13 l4

4.2 How to determine whether electric engine belt is slack: Setting the speed of
treadmill at 1.5kM/H, hold handbar with both hands, try to stop running belt with
feet. lf belt stops and roller still runs, while belt continues to run without
block, it indicates the belt is too slack. User will sometimes feel the sense
of halt. Long-term use will shorten life-span of belt, thus shall be timely adjusted.
4.3 Way to adjust tightness of belt: after a period of use of treadmill, it will halt
sometimes when jogging because the belt is too slack. The tension adjusting
bolts in the left, right and rear adjusting box are used to adjust the degree of
tightness and deflection of the running belt and they are the core part for the
adjustment of the treadmill.
Adjusting method. (Note: Turn clockwise is tight, counterclockwise for
loose. The situation of tight and loose to express both clockwise and
counterclockwise as below) after a specified usage time, the running belt of the
treadmill will extend a little. Skidding will take place in running, which suggests
the running belt is over loosening. Then it is necessary to tighten the tension
adjusting bolts in the rear-adjusting box. Tighten the tension adjusting bolts at
both sides with a standard of quarter circle till no skidding takes place again.
Special attention: lt is not good to adjust belt too tight. Over tightness will shorten
life-span of running belt.
5. Deflection adjustment of running belt:
Though running belt of every treadmill has been adjusted before release and
assembly, it will deflect after a period of use due to the following reasons:
5.1 Host machine is not placed steadily.
5.2 Both feet of the user are not on the center of belt.
5.3 Both feet of the user exert different power.
5.4 Way to adjust deflection: man-caused deflection could automatically restore
by free-load running for several minutes. As to the deflection which cannot
restore, use professional tool available in kit to gradually adjust running belt
adjusting bolt with half circle as one unit. lf the deflection is on the right, adjust
right adjusting bolt clockwise or adjust left bolt anticlockwise. Deflection problem
is mainly maintained by use himself . Deflection will heavily damage running belt.
Once found, the problem shall be timely corrected.
6. Adjustment of electric engine belt:
6.1 Although running belt of every treadmill has been adjusted before release
and assembly, it will deflect after a period of use due to the electric engine belt is
too slack.
6.2 How to determine whether electric engine belt is slack: Setting the speed of
treadmill at 1.SkM/H, hold handbarwith both hands, tryto stop running beltwith
feet. lf beltstops and rollerstill runs, while belt continues to run without block,
it indicates the belt is too slack. User will sometimes feel the sense of halt. Long-
term use will shorten life-span of belt, thus shall be timely adjusted.
6.3 Solution: Adjust bolt of electric engine belt with professional tool for
several rounds clockwise till the user cannot find the sense of halt. The
maintenance is mainly covered by user himself.
Way to adjust electric engine belt: adjust it clockwise with half circle as one unit
with affiliated tool.
It is not good to adjust belt too tight. lt shall be adjusted according to the
requirement. Over tightness will shorten life-span of running belt.
V. General troubleshooting Methods:
Mdfmction Possble Reasons Cleckirg ways Troubleshodirg
t\.rcth ori s
Ndhing displayed
in electronic mder
1. The plug is rct wel
conrEcted with tlc power.
1. Check whether fit
colnec{ion d lir*4e ir
cmnec'ted.
1. Conned the plug
and linkage 4ain
2. \Mretherthe porler ha
been on 2. Check whether tle pore son 2. Restat tle power
Mdorhils
1. Related motor wires
are $nomd 1. Check vhether moto
wires are well DUooed 1. Plq mdor wies
aoain
2. Has not presse(
qTAPT KtrV . Check whether the key ir
rrplid nr nn crrrilnh 2. Press STARTKE\ :nain anr{ tacl
3. Ha rDt plugge(
securitv switch or fall ofi l. Check whether secudt ;vritch is wdl duooed l. Reset securit)
rwilch
4. Wrether Mdc pin falr
rff or motor is bd 4. Exchange t€st to se( ruhether molor is bad 1. Charge motq
5. The poruerorthewong
specificdion controller
AC(110230V
5. \Mdher the specifcatbr
is correct.
i. Choce the correc
ipecification and re
cslinn
No speed state SENSOR is bad in
sensing
1. Cfeck the distana
beturleen SENSOR an(
magndic stme 6 v\ell ar
tle bcdim
1Adjrst the
distance within srn/m
2. Check the wires are shor
cicuit or damaged becaus
of turndf 2. Change wires o
SENSOR
3. Check the uires whethe
are wel conred. 3. Hug and urplu(
wires main
Lack d strokes,
ghcting -@k of PA circuit berc
lr badly flaced cmnedor Iake lower cwer and pres
:o test vfiether PA circu
load is short cirorit q hll
Place conreclo
again and lod
screws
Heart rate display
fails
iENSOR is bad ir
iensing
1. Check wlether wires ar
sltrt circuit q fall off
2. CtEck whether wires mc
Teter ae not wdl comected 2. Hug and umlu(
wires 4ain
2. Bad sersirg of tht
rrrlv lrrin\ 3. Mcisture both hards o
icrub them 3. Court again
E01 Signal communication
hils
1. Eleclronic control En(
eledronic mder cannc
cqnmunicate. Check ead
ioint fron dedrmic meter t(
eledriccmtol
ccrnmunicatbn wire.
Ensure the \ivel
comectbn of eacl
cole.
l5 16

2. check I the wires o
eledronic mder ,Ytc
cokoller are danaged ot
not Cl'nnge tlre wires
fiz Anti-furst+harge
Prdection
1. Check power vdtage i{
lower than 50% cf nqma
udtage.
1. Use correc
voltage specificatior
and test again
2. \Metrer nptor is vrel
clugged 2. Conned rnotor tie
in 4ain ard md<r
sure cf its quality
l. Cfeck wtether ilrre ir
)rld (rcll in nmrr^ro. 3. Charge cmtroller
E6 No sensorsignral
l" Deted m sped senso
riTnal for 5-8 secords
)heck the plug of sensor is
uell pbed or the sensor is
larnaged or not.
1. Plug it wdt o
:hange the sensor
2. or detect no rnotor sigrE
npd fo 58 secords a. mdorwire not v\€l
rlugged or bad motor
fr4
't. check VR wire of rist
motq b vrell pltgged 1. flug \rR wire jcin
again to ensure itl
reliaUlity
Rise fals
2. check VR wire of rist
motq b urell phgged
2. dug AC wie o
rise motor accodins
to the labd on the
corirdler
3. Cfeck whdher the wire o
mottr is damaged oper
cicuit 3. chmge the vrire o
rise motor
4. lf the three pohts ae ok
:he dedrmic controler fails 4. drange thr
eledonic cortrdler
E05 Overflow potection
I
11. Overted leads to th(
lover-qrrfft ald he systen
enters he stde of self
protedion. Or sqne part d
treadmill is jamnred alc
leads to tre stop of mdor.
Overlod and oyer-curert
leads to the selfproEdiat d
the system.
Adjust the teadmil
and saitcfr on.
2. Clpck whether ilrre ir
rverllow sound durirg itl
rpeation or any pardr snrdl lunge tre motor
t7
18
Check whether there
smdl h contrdler Change contrdler
check the vdtage of Try nsiv
voltage to test
antrollq 24C02
eet lC) not well
reversely plqged or
plugged
lV. Exercise lmportant Note
warm-up: Before operation each time, the exerciser shourd do about 5 to i0
minutes warm-ups, incruding warm exercise (such as mark time, treadmiil,
rowing machine, body-buirding machine) and stretch (training the pu, and
extend of the position muscles and articular bend) to avoid to be hurt when
op e rat in g.
Breath: Do not hord the breath when doing exercising. Usuary, breathe with the
nose when preparing or reverting the action, breath with the mouth at fuI tirt
when energizing. The breath shourd assort with the actions. rf the breath is over
hurried, please stop the exercise.
Frequency: The same position of exercising muscre shourd rest for 4g hours;
that is retraining the same part of muscres shourd be after an intervar of
one day.
Burthen: Decide the training burden by individuar energy situation, and then
gradually burthen exercising. lt is common to feel muscle-ache when first
training. As following the frequency above, the ache will disappear.
Relaxation: After training, do five-minute reverted exercise, especiary for
training the stretch and reraxation of the regs' muscres to keep the
muscres' frexibirity and avoid the muscres stiffening for a rong time.
ln order to protect the digestive system, take the training tiil one hour after
mears Take food tiil rralf an hours after exercising. when doing exercise, prease
drink as rittr€ water as possibre, and forbid to drink a lot of water rest to increase
the burdcn of thc: heart and kidney.
our company refiorvos lrro right of finar interpretation for the appearance, specification and
type ofproduct mentionod;rbove. Tho product is subject to change without notice. prease
make the object as the stanclilrcj.