Roby POLARIS User manual

June 16, 2016 Printed in Canada
Instruction Manual
490, rue de l'Argon
Québec, CANADA G2N 2C9
Tél.: [phone] Fax : [phone]
www.jaroby.com
Certified and tested according to
CAN/ULC S627-00
UL 1482-2011
2020 U.S. Environmental
Protection Agency's crib wood
emission standard
PLEASE READ CAREFULLY AND KEEP
THIS MANUAL FOR FUTURE REFERENCE
Product # 10-000
POLARIS —VEGA —CENTAURI

June 16, 2016
TABLE OF CONTENTS
INTRODUCTION......................................................................3
LISTING AND CODE APPROVALS.........................................3
Appliance certification..........................................................3
Mobile home approved.........................................................3
BTU & Efficiency Specifications...........................................3
WARNING................................................................................3
RATING PLATE .......................................................................4
APPLIANCE DIMENSION........................................................5
SPECIFICATIONS ...................................................................5
CLEARANCES TO COMBUSTIBLE MATERIAL......................5
INSTALLATION........................................................................6
Fire Prevention.....................................................................6
Floor protection....................................................................6
Floor protection plate minimum dimensions ....................6
Clearances of the stove until the floor plate protection....6
Minimums clearances to combustible material.....................7
Assembly before installation ................................................8
Leg installation.................................................................8
Pedestal installation.........................................................8
Fan and Snap disc box installation..................................8
Warmer stove Assembly (Optional).................................9
Firebricks installation..........................................................11
Side firebrick installation................................................11
Back firebrick installation...............................................11
Floor firebricks installation.............................................11
Angle firebricks installation ............................................11
Firebrick installation on the pipes...................................12
GENERAL STOVE INSTALLATION STEPS..........................13
Location considerations .....................................................13
General steps of installation...............................................13
Chimney connector installation ..........................................14
Mobile home installation.....................................................15
Chimney installation, General steps...................................16
Inside Masonry Chimney, Vertical Installation ...............17
Outside Vertical Installation...........................................17
Cathedral Vertical Installation........................................17
Offset Installation...........................................................18
Vertical Installation.........................................................19
EXTERNAL COMBUSTION AIR SOURCE............................20
Exterior Air Intake pipe.......................................................20
Installation of Air Intake Pipe.........................................20
Air Inlet Obstruction.......................................................20
STAINLESS STEEL TUBES REPLACEMENT ......................21
Stainless steel tubes Installation........................................21
How to install tubes .......................................................21
OPERATING INSTRUCTIONS..............................................22
Primary and secondary air admission control....................22
Lightning fire......................................................................22
First fire..............................................................................23
Keep a fire .........................................................................23
Fan Control........................................................................23
Fuel Selection....................................................................23
Moisture Meter Information............................................23
Things not to burn..........................................................24
Wood storage ....................................................................24
Draft...................................................................................24
MAINTENANCE.....................................................................24
Ash Removal .....................................................................24
Ash Disposal......................................................................24
Creosote Formation...........................................................24
Chimney Inspection ...........................................................25
Chimney Sweeping............................................................25
Door maintenance..............................................................25
Air tight Adjustment............................................................25
Door adjustment (right side) ..........................................25
Cleaning up glass..........................................................25
Uninstalling and installing door......................................25
Replacing broken glass .................................................26
Fiberglass rope replacement.........................................26
WHAT TO DO IN CASE OF CHIMNEY FIRE ........................26
APPENDIX 1..........................................................................27
Exploded diagram of door..................................................27
APPENDIX 2..........................................................................27
Fans electric wiring diagram..............................................28
APPENDIX 3..........................................................................29
Parts that can be replaced.................................................29
ANNEXE 4 .............................................................................30
Pedestal installation...........................................................30
APPENDIX 5..........................................................................33
Dimension and quantity of bricks.......................................33
J. A. ROBY LIMITED LIFE WARRANTY................................34

June 16, 2016 3
INTRODUCTION
This manual describes the operation and installation of J.A.
Roby woodstove model: Polaris, Centauri, Antares, Sirius, Rigel,
and Vega. This appliance responds to 2020 US Environment
Protection with sized controlled crib wood. The capacity of this
appliance is from 11000 BTU/h to 27000 BTU/h.
Read all instructions carefully before installing your new J.A.
Roby stove. A good installation is very important for a safe and
effective use of this appliance. If you have doubts about the
instruction to install your appliance correctly, we suggest to call
a professional installer. A wrong installation may result in a fire,
burns and possible death.
Keep these instructions for future reference.
This appliance must be connect to:
A HT type factory-built chimney approved UL103 or ULC
629 with 6 inches diameter (15.24 cm);
A code-approved masonry chimney with a flue liner with a
6 inches diameter (15.24cm).
LISTING AND CODE APPROVALS
Appliance certification
The Polaris, Antarès, Sirius, Centauri, Rigel, Véga wood stove
meets the 2020 U.S. Environmental Protection Agency's crib
wood emission standard.
This appliance also meet:
UL 1482-2011 Standard for Solid-Fuel Type Room
Heaters;
ULC S627-00 Standard for Space Heaters for Use
with Solid Fuels;
(UM) 84-HUD, Mobile Home approved.
This wood heater has amanufacturer-set minimum low burn rate
that must not be altered. It is against federal regulations to alter
this setting or otherwise operate this wood heater in a manner
inconsistent with operating instructions in this manual.
This wood heater needs regular inspection and repair for
proper operation. It is against federal regulations to operate
this stove in a manner inconsistent with the instruction in this
manual.
Mobile home approved
This appliance is approved for mobile home installations. The
structural integrity of the mobile home floor, ceiling, and walls
must be maintained. The appliance must be properly grounded
to the frame of the mobile home and used only a listed double-
wall connector pipe.
The appliance must be fixed on the floor.
Do not install in a sleeping room.
Exterior air inlet is mandatory for mobile home use.
BTU & Efficiency Specifications
Average efficiency 75.66%
Particle emission 1.36g/h
Minimum Heat Output* 11'440 BTU/hr
Maximum Heat Output* : 27'214 BTU/hr
Vent size 6"
Firebox size 1.83 cubic feet
Recommended wood length: 18 inches
Fuel Orientation: side to side.
Fuel: Seasoned cord wood.
* A range of BTU outputs based on Environment Protection
Agency Default Efficiency and the burn rates from the low and
high Environment Protection Agency emission tests, using
Douglas fir dimensional lumber.
WARNING
If this appliance is in an area where children may be near, it
is recommended that you place a decorative barrier in front
of the appliance.
N.B: BE WARNED THAT THE LOCAL CODES AND RULES
CAN HAVE MORE SPECIFIC REQUIREMENT THAN THIS
MANUAL. YOU CAN CONSULT A PROFESSIONAL
INSTALLER, OR ASK FIRE OFFICIALS OR LOCAL
AUTHORITY ABOUT RESTRICTION AND INSTALLATION
INSPECTION IN YOUR AREA.
YOU MIGHT NEED TO OBTAIN A PERMIT FOR INSTALLING
CHIMNEY AND STOVE.
DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY FLUE
SERVING ANOTHER APPLIANCE.
DO NOT CONNECT TO OR USE IN CONJUNCTION WITH
ANY AIR DISTRIBUTION DUCTWORK UNLESS
SPECIFICALLY APPROVED FOR SUCH INSTALLATIONS.
THIS APPLIANCE IS BUILT FOR BURNING SEASONED
CORDWOOD ONLY. USE OF ANY OTHER TYPE OF FUEL
LIKE COAL/ CONSTRUCTION WOOD/ TREATED WOOD/
FLAMABLE LIQUID/ TRASH/ OR ANY FLAMABLE THING
CAN OVERFIRE AND DAMAGE THE STOVE.

June 16, 2016 4
RATING PLATE

June 16, 2016 5
APPLIANCE DIMENSION
SPECIFICATIONS
Option
Polaris, Sirius
Vega, Antares
Rigel, Centauri
Combustible
Wood
Wood
Wood
Recommended
surface area
1800 ft²
1800 ft²
1800 ft²
Capacity
27214 BTU/h
27214 BTU/h
27214 BTU/h
Flue pipe diameter
6 in (15.4 cm)
6 in (15.4 cm)
6 in (15.4 cm)
Minimal chimney
height
12 ft (366 cm)
12 ft (366 cm)
12 ft (366 cm)
Exterior Height
33 in (83.8 cm)
41.3 in
(104.1 cm)
54 1/8 in
(137.5 cm)
Exterior Width
26 7/8 in
(68.3 cm)
26 7/8 in
(68.3 cm)
26 7/8 in
(68.3 cm)
Exterior Depth
25 ½ in
(64.8 cm)
25 ½ in
(64.8 cm)
25 ½ in
(64.8 cm)
Door Opening
15 5/8 in x 9 1/8 in
40.0 cm x 23.2 cm
15 5/8 in x 9 1/8 in
40.0 cm x 23.2 cm
15 5/8 in x 9 1/8 in
40.0 cm x 23.2 cm
Interior Height
10 7/8 in
(27.6 cm)
10 7/8 in
(27.6 cm)
10 7/8 in
(27.6 cm)
Interior Width
18 3/8 in
(46.7 cm)
18 3/8 in
(46.7 cm)
18 3/8 in
(46.7 cm)
Interior Depth
15 3/4 in
(40 cm)
15 3/4 in
(40 cm)
15 3/4 in
(40 cm)
Maximum log
length
18 in
(45.7 cm)
18 in
(45.7 cm)
18 in
(45.7 cm)
Average
combustion time
3 to 8 hours
3 à 8 heures
3 à 8 heures
Weight
266 lb
(120.7 kg)
297 lb
(134.7 kg)
320 lb
(145.1 kg)
CLEARANCES TO
COMBUSTIBLE
MATERIAL
All models
Back
10 in (25.4 cm)
Beside
20 in (50.8 cm)
Front
48 in
(121.9 cm)
Minimum Ceiling
Height
84 in
(213.4 cm)
Back of Flue Collar
11 in (27.9 cm)
Side of Flue Collar
29.4 in
(74.6 cm)
In corner
installation
8 inches
(20.3 cm)

June 16, 2016 6
INSTALLATION
Fire Prevention
To provide reasonable fire prevention, the following should be
given serious consideration:
1. At least one smoke detector on each floor of your home
should be installed to ensure your safety. They should be
located away from the heating appliance and close to the
sleeping areas. Follow the smoke detector
manufacturer’s placement and installation instructions,
and be sure to maintain regularly.
2. A conveniently located Class A fire extinguisher to
contend with small fires resulting from burning embers.
3. A CO detector should be installed in the room with the
appliance.
4. A practiced evacuation plan, consisting of at least two
escape routes.
5. A plan to deal with a chimney fire as follows:
a.In the event of a chimney fire:
b.Evacuate the house immediately
c.Notify fire department.
Floor protection
Your stove must be installed on a non-combustible material
plate to protect the floor and avoid fire caused by:
Projections of sparks when opening door or loading
logs;
The heat radiation from stove runaway which might
cause an auto-ignition to the floor and the coating;
Flow of creosote when there is a fire chimney.
The coating used for the protection must be non-combustible
and approved according to standard UL1618 for USA or
approved to the locals codes (Example: cement, brick, ceramic
tiles, etc.)
HORIZONTAL VENTING MANDATORY Non-combustible
floor protections must extend beneath the flue pipe when
installed with horizontal venting and it should extend 2 inches
(51 mm) beyond each side of the pipe.
You can extend the protection plate while respecting the
clearances of each side of stove.
Floor protection plate minimum dimensions
The following dimensions are the minimums values and it can
be higher.
Canada:
44 ¾ inches (113.73 cm)
53 ¾ inches (136.53 cm)
3/8 inch thick (1 cm)
United States:
44 ¾ inches (113.73 cm)
51¾ inches (131.44 cm)
3/8 inch thick (1 cm)
8.0"
20.3cm
8.0"
20.3cm
8.0"
20.3cm
45.0"
114.3cm ÉU/USA
16.0"
40.7cm ÉU/USA
47.0"
119.4cm Canada
18.0"
45.7cm Canada
41.2"
104.8cm
Clearances of the stove until the floor plate
protection
The following dimensions are the minimums values and it can
be higher.
Canada:
8 in (20.3 cm) behind
8 in (20.3 cm) beside
18 in (45.7 cm) in front of the door opening.
United States:
8 in (20.3 cm) behind
8 in (20.3 cm) beside
16 in (40.64 cm) in front of the door opening.

June 16, 2016 7
Minimums clearances to combustible material
With these reduced clearances, this appliance take a minimum
space to be installed. Whether in the living room or the dining
room, this appliance will complete your decorate by his
originality and heating. It requires a minimum clearance of 10
inches (25.4 cm) to the back (for a smoke simple pipe with a
heat shield) and a 20 inches (50.8 cm) lateral MINIMUM
clearance.
29.4"
74.8cm
20.0"
50.8cm
11.0"
27.9cm
10.0"
25.4cm
In the case with a smoke simple pipe without heat
shield, you must installed the stove that the
smoke pipe is to 18 inches (47.5 cm) of all
combustible material therefore the MINIMUM
clearance at the back of the stove will be 12½
inches (41.3cm).
For a 45° corner or other corner installation, the
minimum clearance between the stove and
combustible material must be 8 inches.
18.5"
47.0cm18.5"
47.0cm
8.0"
20.3cm8.0"
20.3cm
To know how to reduce that dimension, you have to
contact your local authority for installing heat shield on
a wall. The Installation with reduced clearances must
comply with standard NFPA211 or CAN/CSA-B365.

June 16, 2016 8
Assembly before installation
Depending on the option you chose, the stove legs might not
have been assembled in the shop in order to save space for
storage and shipping. You must therefore assemble them before
installing the stove.
Leg installation
1) Remove legs and bricks from combustion room.
2) Unscrew the stove from the skids.
3) Put the stove on the back and be careful to protect the
paint.
4) Unscrew the nut (#2) at the corners without removing
completely.
5) Install the legs (#1) as illustrated and secure it with nut
and washer (#2, #3) (Attention: Be sure the legs are in
place, correctly positioned and in contact with the
bottom of the stove.)
Pedestal installation
See appendix 4.
Fan and Snap disc box installation
1) Screw the fans on the ventilation box as illustrated.
Make sure to place the cables as shown.
Fan
Screws
Grate
2) Screw snap disc box into the holes made for that at the
back side near the vent box.
Star Washer
Screw
Thermodisc
Box
WARNING: NEVER ROUTE POWER CORD UNDER
OR IN FRONT OF THE APPLIANCE.

June 16, 2016 9
Warmer stove Assembly (Centauri Cuisiniere)
Now, you need to know which type of smoke pipe: smoke simple
pipe or smoke double pipe.
For the smoke simple pipe, it’s not necessary to remove the pre-
cut metal part.
For the smoke double pipe, you must remove the pre-cut metal
part on the top, inside and in front of the warmer. See pictures
below.
1) Put the packaging product on the ground and put the back
on it to protect the painted part.
2) Fix the left side.
3) Fix the right side.
4) Fix the front (with the door) with the two sides and the
back. Keep the horizontal holes empty for the chrome
decoration.
5) Insert the chrome decoration in the hole and fix-it with
carriage bolt and nut (2 bolts each) .

June 16, 2016 10
6) Fix the top with the back and with the front as well.
7) Fix the left decorative panel side and install the left
chrome decoration.
8) Fix the right decorative panel side and finish installing
the right chrome decoration.
9) Put and fix the warmer with the 6 holes of each side to
the cook stove.

June 16, 2016 11
Firebricks installation
Side firebrick installation
Put 4 bricks "A" as shown.
Back firebrick installation
Put 3 bricks «A» and 1 brick «C» on the back wall.
Floor firebricks installation
Put 2 Bricks «F» near the wall and 2 bricks «D» in the center.
Angle firebricks installation
Put «C» and «E» brick on the top of the back bricks and tangent
to the last tube.

June 16, 2016 12
Firebrick installation on the pipes
The firebricks must be put on the 3 pipes from the front of
combustion chamber. Bricks keep the maximum heat inside the
combustion chamber and help the air from the tube burn the most
of the gas from wood which wouldn’t be burnt in any other
manner.
The rockwool above the brick prevents leakage between the
bricks and keep a maximum heat inside combustion chamber. It
must cover up all the bricks and the air corridors of both sides.
IMPORTANT: The rockwool must not obstruct the smoke exit
way. Check from the hole in the flue collar and make sure that is
in the good position. Place two half-round steel parts on the
rockwool as illustrated.
1) Put 3 « A » bricks and 1 «C» brick vertically over the first
three top pipes and push them against the back angle brick.
Be sure to eliminate any space between the back bricks
and the bricks you install as shown.
2) Put the rockwool over the bricks and check from the hole
in the flue collar that the passage of smoke is not
obstructed. There must be 1 inch (2.54 cm) or more
between the rockwool and the deflector.
3) Put two half-round steel disk over the rockwool near the
rear deflector already in place. Be sure to put it under the
rear deflector to maximise the clearance between
rockwool and the rear deflector. Make sure the rockwool
is not obstructig the space by looking from the hole in the
flue collar.
WARNING: Obstructing smoke exit way under deflector can
force fume to exit by the door when open it and the stove
must not work properly.
Half Disk

June 16, 2016 13
GENERAL STOVE
INSTALLATION STEPS
Location considerations
We recommend installation of this appliance by a certified
installer.
Consideration must be given to:
Safety;
Traffic flow;
Convenience;
Chimney and chimney connector required;
Draft.
Drawing your installation plan on paper is a good way to avoid
mistake.
Write on the plan:
Exact dimensions for clearances to combustible
material;
Exact dimensions of the floor protection;
Measurements of the chimney location. (If it not
already installed. Be sure to have all clearances
recommended by the factory-built chimney
manufacturer to pass through the ceiling and roof).
We recommend that a qualified building inspector and your
insurance company representative review your plan before and
after installation.
General steps of installation
1) Read the entire installation manual before installing
and using your stove.
2) Choose a spot where to install your stove. Read
section about floor protection dimension, localisation of
stove over the floor protection plate and combustible
material clearance. Once you have decided where to
install the stove, mark the roofat the center of chimney.
oTo be sure that the vertical center of the chimney,
use a plumb line and mark the center on the floor.
3) Check if it possible to pass chimney without damaging
the structural integrity of your house. If so, you have to
move the location of the stove while keeping the
minimum clearance or more to be sure. If you can’t
move the stove and have to cut through a beam, make
sure to keep the structural integrity of your house by
following state of the art and National building code.
oWe recommend installation of this appliance by a
certified installer.
Note: This appliance have to be connected to 6 inches
(15.24 cm) factory build chimney HT UL 103 or CAN/ULC
S629 compliant or a 6 inches (15.24 cm) masonry chimney
with a homologated sleeve inside.
4) Install the chimney following the manufacturer
instruction.
5) Put the stove directly on the floor aligned vertically with
the center of chimney, and trace the side of the stove
on the floor and remove it.
6) Trace the dimension of protection plate on the floor.
There must be 8 inch (20.3 cm) clearance from the side
and the back of the stove. . From the front of the door
opening, there must be a clearance of 16 inches (40.6
cm) in US and 18 inches (45 cm) in Canada.
7) Install the floor protection plate inside the mark (It must
be non-combustible).
8) Put the stove on the protection floor plate and respect
the offset clearance set at step 6. Be sure to center the
stove under the chimney. We recommend to fix the
stove to the floor with bolt in the slot made for this
purpose in the legs. In a mobile home, it is obliged to
fix the stove.
9) If you have an outside air inlet, you must use 4 inches
(10.16 cm) flexible aluminum pipe. The pipe must be
sealed with thermal resistant sealant and it has an air
intake with grate approved for this purpose.
10) Install the chimney connector on the stove. The pipe
must be fixed with at least 3 screws on the stove collar,
each chimney connector and the chimney collar.
Note: The single wall or double wall chimney connector
must be 6 inche diameter and have a minimum thickness of
24 gauge (0.025 inches 0.64 mm). Do not use galvanised
steel chimney connector.
.

June 16, 2016 14
Chimney connector installation
The chimney connector is a set of single wall or double wall flue
pipes and elbow installed between the stove collar and the
chimney collar. The single wall chimney connector is sold into
any hardware store and are not approved nor certified. Some
rules must be followed to install it and can be found in the
installation codes for wood heater.
Double wall chimney connector
The stove was designed and tested with a single wall
chimney connector with heat shield. However, it is
possible to install a 6 inch (15.2 cm) double wall certified
chimney connector.
ATTENTION:
For the clearance between combustible materials and
double wall chimney connector, see manufacturer manual.
Single wall chimney connector
For the single wall chimney connector, it must be 6 inches
diameter and minimum thickness of 22 gauge 0.029 inches
(0.85 mm).Install a metal heat shield, 1 inches (25.4 mm)
offset for the single wall section and elbow.
ATTENTION:
If heat shield is not present you must move away the
stove to keep 18 inches (45.7 cm) clearance
between combustibles materials and the chimney
connector.
Any horizontal section must have a 1/4 inches (6.35
mm) by feet (30 cm) slope toward the chimney collar.
Clearance between roof and horizontal single wall
chimney connector must be 18 inch (45.7 cm) or
more.
Clearance between roof and horizontal double wall
chimney connector, follow chimney connector
manufacturer indication.
ALL SECTION AND ELBOW MUST BE CLEAN AND
IN GOOD CONDITION AND MUST BE APPROVED
FOR A CORDWOOD FUEL.
Chimney connector assembly installation
1. Make a summary installation of all sections and elbows
(if necessary) to ensure that you meet the clearances and
inclinations of the horizontal sections and verify if you
have all the necessary parts for the final installation.
oFor direct vertical installation, you will need:
1 vertical section of 24 inches or more;
1 adequate length of telescopic chimney
connector section allowing you to connect
the last chimney connector to the chimney
collar.
Note: Additional section can be used for higher roof.
oFor horizontal run installation you will need:
1 adequate length of vertical section
1 x 90° elbow or 2 x 45°elbow.
1 x adequate length of telescopic chimney
connector section.
Note: For better draft performance, two 45 degree
elbow are preferable, with or without straight section
in between.
2. Disassemble the whole thing and restart screwing the
pieces from the stove to the roof chimney collar
3. Insert entirely the rolled end into the stove collar and
screwing it with a minimum of 3 screws.
4. Install all the next section up to the roof chimney
support and screw every chimney connector parts with
3 screws
WARNING: It is mandatory to screw the pipe to the
stove collar and also at each joints with a minimum
of 3 screws.
5. Install all the next section and screw it to the
chimney collar.
DO NOT CONNECT CONECT THIS UNIT TO A CHIMNEY
FLUE SERVING ANOTHER APPLIANCE.
CONNECTOR PIPES SHOULD NEVER PASS THROUGH
THE CEILING, THROUGH A WALL, IN A CLOSET, IN AN
ATTIC OR OTHER ENCLOSED AREA THAT COULD
CAUSE HEAT BUILDUP. IF YOU NEED TO PASS
THROUGH COMBUSTIBLE MATERIAL, MAKE SURE
THAT YOUR INSTALLATION COMPLIES WITH
CAN/CSA-B365.

June 16, 2016 15
Mobile home installation
DANGER: DO NOT INSTALL IN BEDROOM.
WARNING: THE STRUCTURAL INTEGRITY OF THE MOBILE
HOME FLOOR, WALL, AND CEILING/ROOF MUST BE
MAINTAINED.
VAPOR BARRIER EFFICACITY MUST BE KEEPT IN GOOD
CONDITION.
1) Do the General stove installation from steps 1 to 11.
2) The following requirements are MANDATORY for
installation in a mobile home.
a. The stove must be fixed on the floor of
mobile home with bolt and nuts.
b. The exterior air intake must be installed.
c. The stove must be electrically-grounded to
chassis of the mobile home. In USA,
electrical grounding to the certified
terminals with 8 gauge wire and using star
washer are mandatory.
d. All of the following equipment must be
certified and approved for mobile home
installation.
Double wall chimney connector;
The chimney system;
The roof flashing;
The Storm collar;
Cap with spark arrester;
Firewall;
Chimney ceiling support;
Decorative collar.
e. If the chimney is exposed outside from a wall and
placed lower than 7 feet (213 cm) above the
ground level where the mobile home is situated, a
shield must be installed around the chimney from
the bottom to 7 feet (213 cm) high. If openings are
made into the shield, they must be less than ¾
inch (2 cm) wide and keep the distance of 4 inches
(10,2 cm) or more in order to avoid contact with
chimney.
f. The chimney must exceed at least 3 feet (91,4 cm)
from the highest point of opening made in the roof
and exceed also 2 feet from the highest point of
the roof which is 10 feet away from the chimney.
g. Be sure to seal correctly the flashing of the roof,
the firewall and the exterior air inlet with sealant.
You should also pay attention to the efficacy of
vapor barrier.
3) Always keep the door closed. Open it only when add
wood or start fire.
4) To close the exterior air inlet when the stove is not in
use, a damper must be installed in the air intake pipe.
5) Don’t forget to open the damper when operate your
stove so that the smoke will not enter the house.
6) Always use certified parts for mobile home. Never use
a substitute.

June 16, 2016 16
Chimney installation, General steps
Use only approved chimneys, the same size as the output
collar, 6 inches in this case. The chimneys used must be tested
according to CAN/ULC S629 M87 in Canada and to UL 103
(type HT) in USA. The stove can be install with a masonry
chimney according to ULC S635, ULC S640 and UL 1777. The
masonry chimney must be equipped with a stainless steel
sleeve and meet the standards for the masonry chimney with
inner sleeve.
Provide a place to sweeping.
It is preferable, if possible, to avoid an outside chimney or built
on an exterior wall, and this is even more important for colder
areas. Outside chimneys generally have a less efficient draught.
They can even have an inverse draught because it is hard to
heat them enough so that they can reach their operating
temperature. A greater accumulation of creosote, a less efficient
draught and a lesser performance are some characteristics of
cold chimneys. Draught is proportional to the total chimney
height as well as its temperature. It is therefore possible to get a
better draught by increasing the chimney's height and by
reducing the heat loss with an insulated lining. The chimney has
to be installed with a stainless steel lining. Make sure that all
smoke pipe joints are really airtight. A leak reduces the efficiency
of the appliance and could even make its utilization dangerous.
Note: This is a general chimneys installation method.
Always refer to the manufacturer’s manual of the chimney
for a more detailed method for your chimney.
1) Determine the total length needed for your chimney.
2) Cut the holes into all floor and roof
3) If you need to cut a joist, be sure to strengthen the
adjacent joists and frame hole respecting the
minimum dimensions to be maintained between
combustible materials and the firewall. Follow the
manufacturer's instructions in the manual supplied
with the firestop. Never cut a structural beam.
4) Frame the holes in each level and attic respecting the
minimum distance recommended by the
manufacturer's manual of your chimney. Install
firestop in each level.
5) Frame the hole into the roof.
6) Install the chimney support at the ceiling where stove
is installed.
7) Stack and lock the factory built chimney section on
the support and above the roof.
The chimney must be over 36 inches (91.4
cm) over the higher point into the roof
opening.
The chimney must also be 24 inches over
the highest point on the roof inside 10 ft (304
cm) radius around chimney.
The minimum length of chimney is 12 feet
(365.8 cm).
ATTENTION: Be sure the chimney section are locked
together and locked onto the chimney support.
NOTE: More lengthen chimney than the minimum can add
more draft and help to the good working operation of the
stove Try the minimum length first then add section if you
need more draft.
8) Put the roof flashing over the chimney and seal it with
roof caulking.
9) Nail roof flashing, and reinstall roof covering.
10) Slide the storm collar over the chimney and seal it
with high temperature caulking.
11) Lock the chimney cap and install the spark arrestor if
necessary
Note:
Chimney performance may vary.
Buildings, trees, roof line and wind conditions affect
performance, and can make backflow into the
chimney.
Chimney height may need adjustment if smoking or
overdraft occurs.

June 16, 2016 17
Inside Masonry Chimney, Vertical
Installation
The wood appliance must be installed in accordance with the
applicable local laws or the CAN/CSA-B365, NFPA211 (USA)
norms. Follow the chimney manufacturer’s instructions to install
the chimney.
The chimney masonry must have inside a certified metallic
sleeve cover up all the chimney height. The sleeve must be at
the same diameter of the flue collar; 6 inches (15.2 cm). The
junction between sleeve and the chimney connector must be
tight and sealed to avoid fume to go indoor.
To pass into a combustible wall between stove and the masonry
chimney. The installation method have to be safe toprevent fire.
Find the lasts information to your local authority to be sure of the
manner you have to.
To install the stove onto an abandoned masonry fireplace and
use the good condition masonry chimney the chimney must
have inside a certified metallic sleeve cover up all the chimney
height. The sleeve must be at the same diameter than the flue
collar 6 inches (15.2 cm). The junction between sleeve and the
chimney connector must be tight and sealed to avoid fume to go
indoor. Don’t forget to add a sweep opening.
Outside Vertical Installation
The wood appliance must be installed in accordance with the
applicable local laws or the CAN/CSA-B365, NFPA211 (USA)
norms. Follow the chimney manufacturer’s instructions to install
the chimney.
To pass into a combustible wall between stove and the chimney.
The installation method have to be safe to prevent fire. Find the
lasts information to your local authority to be sure of the manner
you have to. An internal fire stop and an external fire stop must
be used.

June 16, 2016 18
Cathedral Vertical Installation
The wood appliance must be installed in accordance with the
applicable local laws or the CAN/CSA-B365, NFPA211 (USA)
norms. Follow the chimney manufacturer’s instructions to
install the chimney.
Always pass chimney between joists. If a joist need to be cut,
referring to the National Building code to know how to do it
safely to avoid structural integrity fail. Call a carpenter or a
certified Installer.
Always frame around chimney. Keep minimal clearances
written into your chimney manual.
Do not fill the gap between the fire stop and the chimney.
Nothing must be in contact with the chimney.
Always install a fire stop at each level, in a Floor, in a ceiling,
attic and in a Roof.
Always pass with a straight section into a level joist.
The chimney should be support by the cathedral roof. Build a
box around it to install ceiling support at is base.
Weight of the chimney never be allow to be support by the
stove.
Offset Installation
The wood appliance must be installed in accordance with the
applicable local laws or the CAN/CSA-B365, NFPA211 (USA)
norms. Follow the chimney manufacturer’s instructions to
install the chimney.
Always pass chimney between joists. If a joist need to be cut,
referring to the National Building code to know how to do it
safely to avoid structural integrity fail. Call a carpenter or a
certified Installer.
Always frame around chimney. Keep minimal clearances
written into your chimney manual.
Do not fill the gap between the fire stop and the chimney.
Nothing must be in contact with the chimney.
Always install a fire stop at each level, in a Floor, in a ceiling,
attic and in a Roof.
A special fire stop need to be install into the attic. It keep
isolation and avoid the attic isolation to be in contact with the
chimney.
Always pass with a straight section into a level joist.
Chimney weight have to be support by the lower level with a
Ceiling support.
Chimney weight have to never be onto the elbows. Install a
support band to support the upper straight section over the
elbow.
Weight of the chimney never be allow to be support by the
stove.
Some restriction have to be respect regarding the maximum
angle and length of the offset. See chimney manual for this
restriction. Or local building code.

June 16, 2016 19
Vertical Installation
The wood appliance must be installed in accordance with the
applicable local laws or the CAN/CSA-B365, NFPA211 (USA)
norms. Follow the chimney manufacturer’s instructions to
install the chimney.
Always pass chimney between joists. If a joist need to be cut,
referring to the National Building code to know how to do it
safely to avoid structural integrity fail. Call a carpenter or a
certified Installer.
Always frame around chimney. Keep minimal clearances
written into your chimney manual.
Do not fill the gap between the fire stop and the chimney.
Nothing must be in contact with the chimney.
Always install a fire stop at each level, in a Floor, in a ceiling,
attic and in a Roof.
A special fire stop need to be install into the attic. It keep
isolation and avoid the attic isolation to be in contact with the
chimney.
Always pass with a straight section into a level joist.
Chimney weight have to be support by the lower level with a
Ceiling support.
Weight of the chimney never be allow to be support by the
stove.

June 16, 2016 20
EXTERNAL COMBUSTION AIR
SOURCE
In conventional designed house, natural ventilation is enough
to operate the wood stove.
In some new energy saving house, natural ventilation is not
enough to good operation of your stove. To avoid reverse
circulation of smoke caused by negative pressure when turning
on some fan such as bathroom fan, cooking fan or a dryer, it is
recommended to install the external combustion air inlet.
Without the external air inlet, open a window slightly in the
room where the appliance is placed in order to avoid the
negative pressure caused by the appliances mentioned above.
A mobile home on a foundation is considered as a
conventional house.
Exterior Air Intake pipe
This appliance is certified for the mobile home installation. An
external air intake is necessary.
We recommend to use a 4 inches (10.7 cm) aluminum flexible
pipe with a dumper outside air inlet equipped with grate.
Other pipe material must be complied with ULC-S110 norms or
UL-181 Class1 norms, equipped with thermal resistant isolation
and must be corrosion resistant.
The stove must be fix to the structure when an exterior air
intake is installed.
Installation of Air Intake Pipe
1) To install the exterior air intake pipe, find the hole
under the stove back and fold the 3 tabs outside the
Intake box. Insert the pipe into the hole and screw the
pipe using the 3 holes in the tabs. Put a generous
layer of high temperature latex caulking onto the joint
to ensure the pipe is sealed.
2) Cut the exterior wall and install Air Inlet kit following
the manufacturer installation instructions. Be sure to
seal it correctly to preserve the vapour barrier of your
house.
3) Install a small rigid section inside the house and put a
damper to close the air Inlet. This damper is to reduce
the cold air circulation into the stove when it is not in
service.
4) Plug the flexible air inlet pipe onto the damper section.
5) Put a thermal resistant isolation onto the pipe if the
pipe is not isolated.
To avoid that the cold air doesn’t come in the stove, we
recommend to install a valve which closes the pipe near the
outdoor air inlet.
Air Inlet Obstruction
If the stove extinguishes after closing the door, it’s possible that
the air inlet is obstructed by something.
After a long unused period, insects or animals can build a nest
inside the air inlet.
After a storm in winter, snow can accumulate over the air inlet
and obstruct it.
Before warming season, always inspect air inlet pipe to be sure
nothing is obstructing the outside air inlet.
Exterior inlet with grate
Adjustable Collar
4 inches rigid or flex pipe