Rocket Medical CRAFT User manual

SERVICE MANUAL
Rocket
®
CRAFT™
and
DUOVAC™
Oocyte Aspiration Pumps

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
2
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:9
25/02/19
1. CONTENTS
1. CONTENTS ................................................................................................................................................................2
2. GENERAL ASSEMBLY ..............................................................................................................................................3
2.1. Rocket CRAFT™ DUO-VAC Suction Pump........................................................................................................3
2.2. Rocket CRAFT™ DUO-VAC Suction Pump –Internal View ...............................................................................4
2.3. Rocket CRAFT™ Suction Pump..........................................................................................................................5
2.4. Rocket CRAFT™ Suction Pump – Internal View.................................................................................................6
3. GENERAL DESCRIPTION:........................................................................................................................................7
3.1. INDICATIONS......................................................................................................................................................7
3.2. CONTRAINDICATIONS.......................................................................................................................................7
3.3. REFERENCES.....................................................................................................................................................7
4. GENERAL INFORMATION.........................................................................................................................................8
4.1. COPYRIGHT........................................................................................................................................................8
4.2. MODEL NUMBERS..............................................................................................................................................8
4.3. MANUAL REVISION:...........................................................................................................................................8
4.4. MANUFACTURER:..............................................................................................................................................8
4.5. SERVICE AGENTS..............................................................................................................................................9
4.6. SUPPLY VOLTAGE SELECTION .....................................................................................................................10
4.7. ELECTROMAGNETIC COMPATIBILITY...........................................................................................................10
4.8. PACKAGING......................................................................................................................................................10
4.9. POSITIONING and PLACEMENT of the DEVICE.............................................................................................10
4.10. SYMBOLS USED ON CRAFT SUCTION & DUO-VAC PUMPS.....................................................................11
4.11. SYMBOLS USED ON R57685 PATIENT CONNECTION SET.......................................................................11
5. GENERAL INFORMATION:......................................................................................................................................12
5.1. General Description:...........................................................................................................................................12
5.2. Indications..........................................................................................................................................................12
5.3. Contraindications ...............................................................................................................................................12
5.4. References.........................................................................................................................................................12
6. ANNUAL SERVICE...................................................................................................................................................13
6.1 Replacing the filter element.................................................................................................................................13
6.2 Replacing the pump valve & diaphragm set ...................................................................................................15
6.3 Reassembling the valve set............................................................................................................................18
7. REPAIRS & REPLACEMENTS ................................................................................................................................20
7.1 Replacing the DUO-VAC Footswitch Connectors...........................................................................................20
7.2 Replacing the gauge in DUO-VAC & Suction Pump models ..........................................................................21
7.3 Bottle Bracket Replacement using Service Kit B02-190S ..............................................................................22
8. FINAL TESTING .......................................................................................................................................................23
9. FUSE REPLACEMENT ............................................................................................................................................24
10. CLEANING THE PUMP CASING...........................................................................................................................25
11. YEAR OF MANUFACTURE:...................................................................................................................................25
12. RETURNING THE PUMP FOR FACTORY REPAIR OR SERVICE ......................................................................25
13. STORAGE ..............................................................................................................................................................26
14. TRANSPORTATION:..............................................................................................................................................26
15. WARRANTY............................................................................................................................................................27
16. TECHNICAL SPECIFICATIONS.............................................................................................................................28
16.1. CLASSIFICATION............................................................................................................................................28
16.2. SPECIFICATIONS...........................................................................................................................................28
17. DRAWINGS ............................................................................................................................................................29
17.1. GENERAL ASSEMBLY....................................................................................................................................29
17.2. GENERAL ELECTRICAL:................................................................................................................................30
17.3. GENERAL INSTALLATION: ............................................................................................................................31

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
3
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:9
25/02/19
2. GENERALASSEMBLY
2.1. Rocket CRAFT™ DUO-VAC Suction Pump
Rocket Craft DUOVAC Pump with footswitch supplied after2013
1. Illuminated O/I Mains Power On/Off
2. Vacuum Control Dial –clockwise to increase, anticlockwise to decrease the setvalue
3. Vacuum Display mmHg-1
4. Footswitch connection ports
5. Water trap connection port –recommended for use with R57685 Rocket Craft Pump Water TrapSets
6. Water Trap Set comprising glass bottle, bung, angled connectors, silicone tube set.
Recommended for use with R57685 Rocket Craft Pump Water TrapSets
7. Silicone tube set with metal luer connector
8. Footswitch: BLACK: Standard: 50-250mmHg-1 and WHITE: High Vacuum 440mmHg-1 foot-switch

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
4
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:9
25/02/19
2.2. Rocket CRAFT™ DUO-VAC Suction Pump –Internal View
1. Vacuum gauge 0-700mmHg –normal range 50-440mmHg-1
2. Illuminated O/I Mains Power On/Off
3. Motor 220VAC 50Hz, 110VAC 60Hz –modeldependant
4. Vacuum outlet port
5. Pump head including valve housing
6. Internal silencer with filter chamber
7. Main power input

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
5
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:9
25/02/19
2.3. Rocket CRAFT™ Suction Pump
1. Illuminated O/I Mains Power On/Off
2. Vacuum Display mmHg-1
3. High Vacuum (440mmHg-1) control button
4. Vacuum Control –clockwise to increase, anticlockwise
to decrease the set value
5. Watertrapconnection port –recommended for usewith
R57685 Rocket Craft Pump Water Trap Sets
6. Disposable Water Trap Set comprising glass bottle,
bung, angled connectors, PVC tube set.
7. Footswitch connection port
8. Medium Vacuum (Standard) 50-250mmHg-1 footswitch
Footswitch supplied on Rocket Craft SuctionPumps
2013 onwards

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
6
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:9
25/02/19
2.4. Rocket CRAFT™ Suction Pump – Internal View
1. Vacuum gauge 0-700mmHg –normal range 50-440mmHg-1
2. Illuminated O/I Mains Power On/Off
3. Motor 220VAC 50Hz, 110VAC 60Hz –modeldependant
4. Vacuum outlet port
5. Pump head including valve housing
6. Internal silencer with filter chamber
7. Main power input

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
7
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:9
25/02/19
3. GENERAL DESCRIPTION:
The Rocket CRAFT™ Oocyte Aspiration Pumps have been developed to provide smooth, low
volume vacuum at a pre-determined negative pressure. Vacuum is activated by a foot operated
toggle air switch controlled by the surgeon performing the oocytecollection.
The range of vacuum is infinitely variable from 10-200mmHg-1 in medium vacuum mode and at a
pre-set 400mmHg-1 in high vacuum mode.
Rocket CRAFT™ Oocyte Aspiration Pumps require either a water trap set (supplied) or R57685
Disposable Rocket CRAFT™ Water Trap Sets, supplied separately, sterile and for single patient
use.
A suitable collection test tube for use with oocyte needle sets is B.D. Falcon test tube No. 2001F, 17
x 100mm.
3.1. INDICATIONS:
For the generation of high vacuum/low volume suction between 10-400 mmHg-1 to permit the
aspiration of follicular fluid, oocytes and ovarian fluid as part of the treatment of infertility relating to
IVF and other gynaecological procedures.
3.2. CONTRAINDICATIONS:
Not intended for use where ovarian aspiration or the aspiration of ovarian fluid is contraindicated.
For short term operation only. The device is NOT intended for continuousdrainage.
3.3. REFERENCES:
Craft I, McLeod F. Edmonds K, ‘Human embryo transfer technique’. Lancet 1961 ii1104-5
Craft I, Diahanbakch O. McLeod F et al ‘Human pregnancy following oocyte and sperm transfer to
the uterus.’ Lancet 1992 i 1031-3
Craft I, (1984) ‘Clinical Methodology’ British Journal of Hospital Medicine 90-102
Reeves G, Scott R T, et al (1989) Journal of Assisted Reproduction and Genetics Volume6,
Number 6 / December, 1989

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
8
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:9
25/02/19
WARNING:
READ THIS MANUAL
CAREFULLY: Please
familiarise yourself with
the contents of this
manual before
attempting to use the
device.
Failure to observe
these instructions may
result in damage to the
pump or cause injury to
the patient or user.
This device should only
be used by suitably
qualified personnel.
WARNING:
ELECTRIC SHOCK
HAZARD.
The equipment is to be
used only with electrical
systems complying with
all IEC, CEC and NEC
requirements.
CAUTION:
Any adjustment,
modification or repairs
to the equipment
should be carried out
by authorised service
agents.
Disposal of
this device must be
undertaken with regard
to the WEEE directive
(2002/96/EC).
4. GENERAL INFORMATION
4.1. COPYRIGHT
This manual contains information that is subject to copyright. All rights reserved.
This manual should not be photocopied, duplicated or distributed completely or inpart
without the written approval of Rocket Medical plc.
4.2. MODEL NUMBERS:
Rocket Craft™ Suction Pump Complete (110v) R29654
Rocket Craft™ Suction Pump Complete (240v) R29655
Rocket Craft™ Duo Vac™ Suction Pump (240v) R29660
Rocket Craft™ Duo Vac™ Suction Pump (110v) R29661
4.3. MANUAL REVISION:
Revision 1 First Publication 15/02/12
Revision 2 Addition of drawings 29/06/12
Revision 3 Update of tolerance specifications 23/09/13
Revision 4 Update images with new footswitch 30/09/13
Revision 5 Update to latex statement, symbol 06/11/13
Revision 6 Update to YOM, consumption, footer 16/07/14
Revision 7 Update to LRQA CE mark 27/08/14
Revision 8 Update US address 17/01/19
Revision 9 Update Warranty and service addresses
& EU Representative 25/02/19
4.4. MANUFACTURER:
Rocket Medical plc
Sedling Road
WASHINGTON
Tyne & Wear
NE38 9BZ
UK.

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
9
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:9
25/02/19
4.5. SERVICE AGENTS:
Rocket Craft™ Pumps typically require only annual maintenance; however it is
recommended they are serviced and calibrated annually at an approved RocketMedical
plc service facility.
Failure to service the pump at the indicated intervals may invalidate theWarranty.
UK & European Service Agents:
Hunter Scientific Limited
Unit 1, Priors Hall
Widdington, Saffron Walden, Essex, CB11 3SB
Tel: [phone]
Fax [phone]
E: [e-mail]
W:www.hunterscientfic.com
UK Customer Services:
Rocket Medical plc. Sedling Road. WASHINGTON. NE38 9BZ. ENGLAND
Tel: [phone]. Fax: [phone]
Email: [e-mail]
US Office:
Email: [e-mail]
Rocket Medical
50 Corporate Park Drive.
Suite 890.
PEMBROKE.
MA. 02359. USA
Tel: [phone]
Rocket Medical GmbH
Am Rosengarten 48,
15566 Schöneiche.
Germany

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
10
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:8
25/02/19
WARNING:
ELECTRIC SHOCK
HAZARD.
The equipment is to be
used only with electrical
systems complying with
all IEC, CEC and NEC
requirements.
WARNING:
ELECTRIC SHOCK
HAZARD.
Do not immerse the
device.
WARNING:
Device can cause
explosion in the
presence of flammable
gases.
4.6. SUPPLY VOLTAGE SELECTION
The device operates at a voltage 110V 60Hz or 220-240 VAC @ 50Hz. 0.12A depending
on model.
Ensure that the correct power cord is connected.
4.7. ELECTROMAGNETIC COMPATIBILITY
Rocket Craft Suction Pumps comply with the electromagnetic compatibility (EMC) limitsfor
medical devices as specified by IEC 60601-1-2:2001. These limits are designed to provide
a reasonable degree of protection against harmful interference found in typical medical
installations.
Medical electrical equipment requires special precautions regarding EMC and the device
must be installed, positioned and operated according to the instructions contained in this
manual to ensure continued electromagnetic compatibility.
The device must be operated according to the instructions contained in this manualto
ensure continued electromagnetic compatibility.
4.8.PACKAGING
The packaging has been designed to allow secure transportation of the pump andits
accessories.
After unpacking, re-assemble and retain the packaging for transport for servicingwhen
required.
4.9. POSITIONING and PLACEMENT of the DEVICE
Rocket CRAFT™ Oocyte Aspiration Pumps must be placed on a secure, level surface,
away from sources of heat, water splashes, mists or cooling vents. Do not expose todirect
sunlight.
Do not expose to direct sunlight.
Do not expose to flammable gases.
Operating temperature Range: +5°C and +35°C

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
11
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:8
25/02/19
4.10. SYMBOLS USED ON CRAFT SUCTION & DUO-VAC PUMPS.
These tables describe their respective meanings.
Mains Power ON/OFF
This device is Type B
CE Mark
4.11. SYMBOLS USED ON R57685
PATIENT CONNECTION SET.
Read the Instruction for Use before connection and use
Device is for Single Use Only
Device is sterilised by Ethylene Oxide
This device is not manufactured with natural rubberlatex
CE Mark

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
12
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:8
25/02/19
5. GENERAL INFORMATION:
5.1. General Description:
The Rocket CRAFT™ Oocyte Aspiration Pumps have been developed to provide smooth,
low volume/high vacuum at a pre-determined negative pressure. Vacuum is activated by a
foot operated toggle air switch controlled by the surgeon performing the oocytecollection.
The range of vacuum is infinitely variable from 10-200mmHg-1 in medium vacuum mode and
at a pre-set 440mmHg-1 in high vacuum mode.
Rocket CRAFT™ Oocyte Aspiration Pumps require either a water trap set (supplied) or
R57685 Disposable Rocket CRAFT™ Water Trap Sets, supplied separately, sterile and for
single patient use.
A suitable collection test tube for use with oocyte needle sets is B.D. Falcon test tube No.
2001F, 17 x 100mm.
5.2. Indications:
For the generation of low flow/high vacuum between 10-440 mmHg-1 to permit the aspiration
of follicular fluid, oocytes and ovarian fluid as part of the treatment of infertility relating to IVF
and other gynaecological procedures.
5.3. Contraindications:
Not intended for use where ovarian aspiration or the aspiration of ovarian fluid is
contraindicated. For short term operation only. This device is not indicated for continuous
drainage.
5.4. References:
Craft I, McLeod F. Edmonds K, ‘Human embryo transfer technique’. Lancet 1961 ii1104-5
Craft I, Diahanbakch O. McLeod F et al ‘Human pregnancy following oocyte and sperm
transfer to the uterus.’ Lancet 1992 i 1031-3
Craft I, (1984) ‘Clinical Methodology’ British Journal of Hospital Medicine 90-102
Reeves G, Scott R T, et al (1989) Journal of Assisted Reproduction and GeneticsVolume
6, Number 6 / December, 1989

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
13
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:8
25/02/19
WARNING:
ELECTRIC SHOCK
HAZARD.
6. ANNUAL SERVICE
6.1 Replacing the filter element
1. Lay the pump on a clean
surface, protecting the
casing from scratches.
2. Remove 4 screws from
the casing underside and
retain
3. Carefully separate the
case halves, ensuring the
front and rear fascia
plates remain located in
the lower shell.
4. Locate filter housing 
5. Using fingers, lift the top
away from filter chamber.
CAUTION: Avoid the use of
sharp tools as these may
damage the O’ ring.

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
14
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:8
25/02/19
6. Life out the filter
assembly and
remove the filter.
7. Fit new replacement
filter
P/N: E05-000
8. Replace filter,
ensuring the top
seats securely into
the chamber.
9. Avoid trapping or
pinching the ‘O’ ring.
10. Check the top is
correctly seated.

15
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:8
25/02/19
Rocket CRAFT™ Oocyte Aspiration Pumps –ServiceManual
6.2 Replacing the pump valve & diaphragm set
1. Locate the pump silencer
housing and carefully
remove with a gentle
twisting movement.
2. Using a diagonal method,
remove the 4 screws
securing the pump valve
head.
3. Lift the valve head away
from the pump body to
reveal the pump head
gasket and diaphragm
assembly.

16
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:8
25/02/19
Rocket CRAFT™ Oocyte Aspiration Pumps –ServiceManual
IMPORTANT
4. Undo and remove the
centre Pozi drive screw to
release the valve plate.
5. Carefully remove valve
plate from head moulding
with a twisting motion to
separate the two halves
6. Valve gasket and valve
plate.
Note the orientation of
the cut-outs on the
valve gasket in relation
to the valve plate.
7. Lift off pump head gasket
and retain safely.

17
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:8
25/02/19
Rocket CRAFT™ Oocyte Aspiration Pumps –ServiceManual
IMPORTANT
8. Undo and remove the
centre Pozi drive screw
from the pump diaphragm
retaining plate
9. Retain retaining plate and
screw, discard old
diaphragm
10. Replace diaphragm with
P/N: DO1-053
11. Re-assemble and tighten
sufficient to secure the
retaining plate.
DO NOT OVERTIGHTEN
or use excessive force

18
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:8
25/02/19
Rocket CRAFT™ Oocyte Aspiration Pumps –ServiceManual
VERY
IMPORTANT
IMPORTANT
6.3 Reassembling the valve set
1. Ensure the valve plates
are orientated as in the
image (right).
IF THIS ORIENTATION IS
REVERSED, THE VALVE
AND PUMP WILL FAIL TO
OPERATE
2. Replace the valve gasket
with P/N: VO1-002
Note the orientation of the
cut-outs on the valve gasket
in relation to the valve plate
3. Reassemble the valve
head and tighten the
centre screw

19
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:8
25/02/19
Rocket CRAFT™ Oocyte Aspiration Pumps –ServiceManual
IMPORTANT
4. Reseat the pump head
gasket
P/N: GO1-001
5. Replace the valve head
assembly onto the
gasket, ensure the holes
are correctly aligned and
the gasket with seated
correctly.
6. Tighten the valve head
screws in a diagonal
pattern to ensure the
pump head is correctly
seated without distortion.
7. Re-fit the pump silencer
to the head module.

Rocket CRAFT™ Oocyte Aspiration Pumps –Service Manual
20
Copyright© 2012-19
Rocket Medical plc. .
All rights reserved.
ZDOCK226
Rev:8
25/02/19
7. REPAIRS&REPLACEMENTS
7.1 Replacing the DUO-VAC Footswitch Connectors
The front panel connectors of
the DUO-VAC can be subject
to damage through misuse or
repeated over-stressing of the
retaining clips on connection
of the footswitch.
Replacement is a straight
forward operation
1. Remove the upper
casing. (See Section 6)
2. Lift the front panel out of
the retaining grooves on
the lower case
3. Remove tubing by
carefully pulling from
connector.
4. Loosen and remove
securing nut.
5. Replace connector,
locate and tighten
securing nut.
6. Re-fit tubing by pushing
over connector inlet.