Rockford Fosgate T252-S - 5.25'' Original operating instructions

I J w E
Component
Systems
T252-S
-
5.25''
T2652~S
-
6.5''
T2T-S
-
T\Neeter
System
Serial
Number:
------
Installation
&
Operation
Installation
et
fonctionnement
lnstalaci6n
y
funcionamiento
Einbau
und
Betrieb
lnstallazione
e
funzionamento
Date
of
Purchase:
------

SAFETY
.&. CAUTION: Before installation, disconnect the battery
negative
(-) terminal to prevent damage
to the unit, fire and/or possible injury.
PRACTICE SAFE SOUND™
Continuous exposure to sound pressure levels over I OOdB may
cause permanent hearing loss. High powered auto sound systems
may produce sound pressure levels well over 130dB. Use common
sense and practice safe sound.
CARTON CONTENTS
• (1) Set T2 Series Speakers with Tweeters and 2-Way Crossover
or (1) Set T2 Series Tweeters with HP Crossover
• (1) Set of grilles/trim rings
• (2)
Sets of tweeter trim rings:
(1 set of polished aluminum)
(1 set of brushed aluminum)
• Tweeter Mounting Hardware with Surface, Angle, and Flush Mounts
• (I) Set Adapter Plates: T252-S (5"x7"/6"x9"), T2652-S (5"x7"/6"x9")
INSTALLATION CONSIDERATIONS
Before beginning any installation, follow these simple rules:
I.
Be sure to carefully read and understand the instructions before attempting to
install these speakers.
2. For safety, disconnect the negative lead from the battery prior to beginning the
installation.
3. For easier assembly, we suggest you run all wires prior to mounting your speakers
in place.
4. Use high quality connectors for a reliable installation and to minimize signal or
power loss.
5. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines,
brake or hydraulic lines, vacuum lines or electrical wiring when working on any
vehicle. If installation in a boat, take care not to cut or drill through the main hull.
6. Never run wires underneath the vehicle. Running the wires inside the vehicle or
hull area provides the best protection.
7. Avoid running wires over or through sharp edges. Use rubber or plastic
grommets
to protect any wires routed through metal, especially the firewall.
MOUNTING
I. Determine where the speakers will be mounted. Ensure an area large enough for
the speaker to mount evenly. Be sure that the mounting location is deep enough
for the speaker to fit; if mounting in a door, operate all functions (windows, locks,
etc.) through their entire operating
range to ensure there is no obstruction.
2. Refer to the specification chart to determine the proper diameter hole to cut
for your speaker model.The template provided also gives the proper cutout size.
3. Mark the locations for the mounting screws. Drill the holes with a 1/8" bit.
4. Feed the speaker wires through the cutout and connect to the speaker terminals.
Be sure to observe proper polarity when connecting the wires.The speaker's
positive terminal
is indicated with a "+".
5. On models with slotted holes, fit the speaker into the cutout and install the
screws
in the slots at the top and bottom.This will allow you to rotate the speak-
er to match the remaining mounting holes. When aligned, tighten the screws.
6. Tighten the screws until the speaker is snug in place to prevent rattling. Do not
over tighten the screws.
NOTE: If needed, use the adapter plate provided to mount the speaker.
See Adapter Plate Templates at the end of this manual.
2
T252-S Only
Removing tabs for
some installations
A Breakoff
V mounting tab.
0 Use pliers
to break o~
plastic tab.
~··<
~~
Align Holes
Example of standard
door installation
Use tip of a small flat
screwdriver to remove tweeter
Example of Discreet Dual Clamp (DOC™)
Tweeter
Mounting (Flush Mount)

fEATURES
Discreet Dual
Clamp
(DOC™)
Tweeter
Mount
T2
Components
Nominal
Diameter-
inch
(mm)
1252-S
5.
25
(133)
SPECIFICATIONS
12652-S
T2T-S
6.5
(165)
1.0
(25.4)
Every aspect
of
the
newTweeter design has been
completely re-engineered
to
allow for maximum
ease
of
installation and fitment.This
opt
imized
patent pending design provides concentric
clamping pressure around
the
perimeter
of
the
mounting hole.
Description
Component
System
Component
System
Tweeter
System
The
"mounting cups" are
in
fact
not
"cups"
at
all,
but
rather
unobtrusive "clamps"
that
quickly
and easily
mount
in
a standard
1.75
inch (45mm)
hole saw opening with a single
center
screw
securing with balanced pressure
to
both faces
of
the mounting surface. From
there
,
the
tweeter
simply snaps into place and
is
secured
by
a
snap-on trim ring. Removal
is
easy
if
needed.
The
protective grille
on
the
tweeter
is
non-removable and an intergral
part
of
the
design.
WIRING
T2T-S Crossover
Wiring
I.
Use illustration for
proper
connection.
2.
Be
sure
to
maintain speaker polarity.
3. Connecting
the
positive wire
to
OdB
matches the
amplitude
of
the
tweeter
to
the
mid-range (woofer).
4. Connecting positive wire
to
-2dB
or
-4dB
to
reduce
the
amplitude
of
the
tweeter
-2dB
or
-4dB lower
than
the
mid-range, (ideal for tweeters located
high
in
door
panels and mid-range low
in
the kick panel).
Nominal
Impedance
(ohms)
Frequency
Response
(Hz)
Crossover
Frequency
(Hz)
High-Pass
Butterworth
Crossover
Low
Pass
Butterworth
Crossover
Voice
Coil
Diameter-
inch
(mm)
Fs
-
Free
Air
Resonance
(Hz)
Qts
Vas
-
cu
.
ft
.
(Liter)
Xmax-
inch
(mm)
SPL
(dB@
1w/1m)
Power
Handling-Watts
(RMS
I
Peak)
Rec.
Amp
Power-Watts
(RMS)
Mounting
Diameter~nch
(mm)
Mounting
Depth-inch
(mm)
Includes
Grille/Trim
Ring
Trim
Ring
Diameter~nch
(mm)
Trim
Ring
Height-inch
(mm)
Includes
Adapter Plate
See
figures
on
following pages.
Tweeter
On-Axis
Tweeter
Off-Axis
Connect
Only
ONE(+)
Terminal
.....
-.
4Q~
...-
/ ....
~~
9
-
~
.......
.
,:
..
·
........
OR~
....-
3
40
40 40
65Hz-
20kHz
55Hz-22kHz
3kHz-
22kHz
3.5kHz
3kHz 3kHz
18dB/octave
18dB/octave
18dB
/
octave
12dB/octave
12dB/octave
-
1.1
(28)
1.2
(31)
1.0(
25.4
)
65
55
1.8kHz
0.60
0.50
-
0.34
(9.6)
0.56
(16)
-
0.
16
(4.0)
0.24
(6.0)
-
87dB
89dB
90dB
75/150
100/200
75
/
150
22
.5W-75W 30W- 1
00W
22
.5W-75W
4.
80
(122)
5.
59
(142)
1.75
(45)
(Flush
Mount)
2.
03
(52)
2.
51
(64)
0.
95
(24)
(Flush
Mount)
YES
YES YES
6.22
(158)
6.949
(177)
2.13
(54)
1.
06
(27)
1.18
(30)
0.
31
(8)
5"x7"/6"x9"
5"x7"/6"x9"
NO
Specifications subject
to
change
without
notice.
Tweeter
(TWT)
ot-t
··
.
0i='f=\\
-''i------'
·--
..
---··
Connect
Only
~--'"'o,I:·-'J
ONE
(+)Termi
n
al

T252-S & T2652-S Component Wiring
I. Use illustration for proper connection.
2. Be
sure to maintain speaker polarity.
Axis ON-OFF Switch
I. Set to ON or OFF to match position of tweeter re la-
tive
to listener. Default OFF pos i tion satisfies most
installations.
dB Switch
I. OdB matches the amplitude (no increase/ no attenuation)
of the tweeter to the same level as the mid-range
(woofer).
2. +2dB increases and -2dB reduces
the amplitude of
tweeter in relation to the mid-range, (ideal when match-
ing offset installation like
tweeters located high in door
panels and midranges low in ki ck panels).
Tweete r On-Ax is Tweete r Off-Axis
Tweeter Axis Sw i tch
· ·- ·· --- .- --
. .
·---- ---- -- ---- -- -- -- --- - --- - -- -- ··:-·· - ---- -----·
+2dB
Woofe r
(WFR)
u
Tweete r
( TWT )
..... -- ~~~ ....
-: ~----------------------------------------~
TweeterAttenuati on Switch \ . :?~ - ~- ·/
T252-S & T2652-S Bi-Amp Cossover Wiring
I. Use illustration for proper connection and be sure to maintain speaker polarity.
2. Remove 4 screws from
crossover bottom to detatch cover.
3.
When BI-AMP switched OFF for one amplifie r, use only " TWT " input.
4.
When BI-AMP switched ON for two dedicated amplifier, use both " TWT " and " WFR " inputs.
Default Setting
·- .. .
81-AMP -._
/ OFF-, r ON \
-------------------- -- ---- ---- ------ -- ------------- ~- .. ~ IIIB ~ )
... . _ ...
\
Crossover
Cover Removal
Remove 4Sc rews Fr om
Bottom to Detatc h Cov er _
__ __ ___ ___ ':'_i _~ ~':!!P .. ~~~':' __ _ ___ _ __ _ __ _ __ _ __ __ _ __ _____ ___ _
-- ~--
B~AMP -._
/ OFF-, r ON ·.
\. . ~ Elllll ~ )
.. _ __ .. ··
4
Tweet er
(TWT)
T wee ter
(TWT)

T252-S
6.02
11
(153mm)
Tweeter
0.30"
(Smm)
5.43
11
(138mm)
Diameter
Mounting Hole Mounting
Flush
Mount
Diameter Depth
0 32" 1.75" -- -1
h n e
without
notice.
Specifications subject
to
c a g
SPECIFICATIONS
T2652-S
·~·-
0.97"
(2t~~-
L
1.26" J
(32mm)
s
6.18
11
(157mm)
Diameter
T
T252-S
&
T2652-S
Component
Crossover
4.57"
(116mm)

Fran~ais
A\
MISE EN GARDE : avant d'entamer !'installation, deconnectez
Ia
L.1..1
broche negative(-) de
Ia
batterie
pour
eviter
tout
risque
de
blessures,
d'incendie
ou
de
dommages
a
l'appareil.
PRATIQUEZ
UNE
ECOUTE
SANS
RISQUESMo
Une exposition continue a des niveaux
de
pression acoustique superieurs
a I00
dB
peut
causer une
perte
d'acuite auditive permanente.
Les
systemes audio de forte puissance
pour
auto
peuvent produire des
niveaux de pression acoustique bien au-dela de 130
dB.
Faites preuve
de
bon sens
et
pratiquez une
ecoute
sans risques
Notes
pour
l'installation
Avant
de
commencer
!'installation, suivez les regles ci-dessous :
I.
Veillez
a
bien lire
et
comprendre
les instructions avant d'essayer d'installer les
haut-parleurs.
2.
Par mesure
de
securite, debranchez
le
fil
negatif
de
Ia
batterie avant
de
com-
mencer
!'installation.
3.
Pour faciliter
le
montage des haut-parleurs,
il
est
conseille d'installer
tous
les
cables au prealable.
4.
Utilisez des connecteurs
de
haute qualite
pour
assurer
une installation fiable
et
reduire au minimum
Ia
perte
de
signal
ou
de
puissance.
5.
Reflechissez bien avant de percer.Veillez a ne pas Couper
ou
percer
le
reser-
voir d'essence,
le
cablage electrique
ou
les conduites
de
carburant, de freinage
hydraulique ou de depression en travaillant
sur
un vehicule.
En
cas d'installa-
tion
sur
un
bateau, veillez a ne pas
couper
ou
percer
Ia
coque
principale.
6.
Ne
jamais faire passer de
fils
sous
le
vehicule. Leur installation a l'interieur du
vehicule ou
de
Ia
coque
assure
Ia
meilleure protection.
7.
Evitez
de
faire passer des
fils
sur
des
bords tranchants
ou
dans des orifices a
aretes
vives. Utilisez des bagues en caoutchouc
ou
en plastique
pour
proteger
les
fils
traversant une plaque
de
metal,
notamment
le
tablier.
Montage
I. Determinez !'emplacement des haut-parleurs.Veillez
ace
que
Ia
surface plane soit
assez grande pour assurer
un
contact uniforme du haut-parleur.Verifiez que !'em-
placement
est
assez profond pour
le
haut-parleur; en cas de montage dans une
portiere, actionnez toutes
les
commandes (fenetres, serrures, etc.) jusqu'aux
extremites de leurs courses pour vous assurer
qu'il
n'y
a pas d'obstruction.
2.
Consultez
le
tableau des caracteristiques pour determiner
le
diametre de !'orifice
a decouper pour votre modele
de
haut-parleur.
Le
gabarit fourni donne aussi
le
bon diametre de decoupe.
3.
Marquez !'emplacement des
vis
de montage. Percez
les
trous avec une meche de
I
/8 de pouce (3,2 mm).
4.
Faites passer les
fils
de haut-parleur a travers !'orifice decoupe
et
branchez-les
aux bornes
du
haut-parleur.
Veillez
a bien respecter
Ia
polarite lors
du
branche-
ment.
La
borne positive du haut-parleur
est
indiquee par
un
« +
».
5.
Sur
les
modeles a trous allonges, mettez
le
haut-parleur en place dans
Ia
decoupe
et
installez
les
vis
dans
les
trous du haut
et
du bas.Vous pourrez alors
fa.ire
tourn-
er
le
haut-parleur pour !'aligner sur les autres trous de montage. Une
fois
cet
alignement effectue, serrez
les
vis.
6.
Serrez les
vis
jusqu'a ce que
le
haut-parleur soit bien ajuste, de
fa~on
a prevenir
tout
cliquetis, mais evitez
tout
serrage excessif.
REMARQUE: Utilisez
si
necessaire
Ia
plaque d'adaptation fournie pour
monter
le
haut-parleur.Voir
les
gabarits de plaque d'adaptation a
Ia
fin
de
cette
notice.
6
Espaiiol
1'
PRECAUCION: Antes
de
Ia
instalaci6n, desconecte
el
terminal
L.l..1
negative
de
Ia
baterla
(-)
para prevenir dano a
Ia
unidad, incendio y/o
posibles lesiones.
PRACTIQUE
EL
SONIDO
SEGURO
El
contacto continuo con niveles de presion de sonido superiores a I00
dB
puede causar
Ia
perdida permanente de
Ia
audicion.
Los
sistemas de sonido para
automoviles de alta potencia pueden producir niveles de presion de sonido
superiores a los
130
dB.
Use su sentido comun y practique
el
sonido seguro.
Consideraciones
para
Ia
instalaci6n
Antes de comenzar cualquier instalacion,
siga
estas simples normas:
I.
Asegurese
de
leer cuidadosamente y de
entender
las
instrucciones antes
de
tratar
de
instalar
estes
altavoces.
2.
Per
seguridad, desconecte
el
conductor
negative de
Ia
baterla antes de comenzar
Ia
instalacion.
3.
Para facilitar
el
montaje, sugerimos que tienda
todos
los cables antes
de
montar
sus altavoces en su sitio.
4.
Utilice conectores de alta calidad para
tener
una instalacion confiable y para
reducir
al
mlnimo
las
perdidas de senal
0
de
potencia.
5.
jPiense siempre antes de perforar! Tenga
cui
dado
de
no
cortar
ni
perforar en tan-
ques
de
combustible, tuberlas de combustible, frenos o hidr.iulicas, tuberlas de
vade
o cableado electrico
al
trabajar en
un
vehlculo.
Si
Ia
instalacion se hace en
un
bote, tenga cuidado
de
no
cortar
ni
perforar a traves del casco principal.
6.
Nunca tienda cables abajo del vehlculo.Tender los cables adentro del vehlculo o
casco proporciona
Ia
mejor protecci6n.
7.
Evite
tender
cables arriba o a traves
de
bordes filosos. Use arandelas aislantes
de
caucho para proteger los cables tendidos a traves
de
metal, especialmente
Ia
mampara cortafuegos.
Montaje
I.
Determine adonde se montara los altavoces.Asegurese
de
que
haya
un
area
sufi-
cientemente grande para montar
de
man
era
plana
el
altavoz.Asegurese
de
que
el
Iugar de montaje sea suficientemente profundo para que quepa
el
altavoz,
si
se
menta en una puerta, accione todas
las
funciones (ventanas, cerradura, etc.) en
toda
su gama de funcionamiento para asegurarse
de
que no
haya
obstrucciones.
2.
Consulte
Ia
tabla de especificaciones para determinar cuales son los diametros
correctos para
el
agujero a
cortar
para su modele de altavoz.
La
plantilla propor-
cionada tambien
le
da
Ia
medida correcta del recorte.
3.
Marque
las
localidades para los tornillos
de
montaje. Perfore
los
agujeros usando
una broca de I
/8
pulg.
4.
Tienda los cables del altavoz a traves del
recorte
y conecte a los terminales del
altavoz.Asegurese de usar
Ia
polaridad correcta
al
conectar los cables.
El
terminal
positive del altavoz
esti
identificado con
un
slmbolo
"+".
5.
En
los modelos con agujeros ranurados, coloque
el
altavoz en
el
recorte
e instale
los tornillos en
las
ranuras en
Ia
parte superior e inferior. Esto
le
permitir.i hacer
girar
el
altavoz para que coincida con los agujeros de montaje restantes. Una vez
alineados, apriete los tornillos.
6.
Apriete los tornillos hasta que
el
altavoz
este
ajustado en su sitio para evitar
vibraciones.
No
apriete demasiado los tornillos.
NOTA:Use
Ia
placa adaptadora proporcionada para
montar
el
altavoz.
Con
suite
las
plantillas
de
las
placas adaptadoras
al
final
de
este
manual.

Deutsch
&.
VORSICHT:
Entfernen
Sie
vor
dem
Einbau
den negative Batteriepol,
urn
Schaden
am Gerat, Feuer bzw. moglicheVerletzungen
zu
vermeiden.
PRAKTIZIEREN
SIE SICHEREN
SOUND
Fortgesetzte Gerauschdruckpegel von
uber
I
00
dB konnen beim Menschen zu
permanentem
H6rverlust
fuhren. Leistungsstarke Autosoundsysteme k6nnen
Gerauschdruckpegel erzeugen, die
weit
uber
130 dB liegen.
Bitte
wenden
Sie
gesunden Menschenverstand
an
und praktizieren
Sie
sicheren Sound.
Einbauuberlegungen
Befolgen Sie
vor
dem
Einbau diese einfachen Regeln:
I.
Lesen
Sie
dieAnleitung sorgfaltig, bevor
Sie
versuchen diese Lautsprecher einzubauen.
2.
Entfemen
Sie
vor
dem Einbau
aus
Sicherheitsgri.jnden
das
negative Kabel von
der
Batterie.
3.
Um
die Montage zu erleichtem,empfehlen
wir
aile Kabel
vor
der
Befestigung
lhrer
Lautsprecher zu verlegen.
4. Verwenden
Sie
nur
Qualiriitsstecker,
um
einen zuverlassigen Einbau zu gewahrleisten
und
Signal-
und Stromverlust zu minimieren.
5.
Denken
Sie
nach, bevor
Sie
bohren! Achten
Sie
darauf, nicht in den Benzintank, die
Benzin-, Brems-
oder
hydraulischen Leitungen,Vakuumleitungen
oder
Elektrokabel
zu
schneiden
oder
zu bohren,wenn
Sie
am Fahrzeug arbeiten.Achten
Sie
beim Einbau in
einem
Boot
darauf, nicht durch den
Bootsrumpf
zu schneiden
oder
zu bohren.
6.
Verlegen
Sie
Kabel nie
unter
dem Fahrzeug.
Die
Kabel im Fahrzeug
oder
Bootsrumpf
zu verlegen, bietet den besten Schutt.
7.
Vermeiden
Sie
es,
Kabel
uber
scharfe Kanten zu verlegen.Verwenden
Sie
Gummi-
oder
Plastikringe,
um
Kabel zu schlitzen,die durch Metall verlegt
werden
(besonders die
Feuerwand).
Befestigung
I. Entscheiden,
wo
die Lautsprecher befestigt
werden
sollen. Gewahrleisten, dass
der
Platz ausreicht,
um
den Lautsprecher gleichmaBig zu befestigen. Gewahrleisten,
dass
die Befestigungsstelle ausreichendeTiefe
fur
den Lautsprecher hat; beim Einbau in
einer
Ture
aile Funktionen (Fenster, Schloss usw.) in
ihrem
ganzen Bereich auspro-
bieren
um
zu gewahrleisten,
dass
keine Blockierung
eintritt.
2.
Die
Tabelle in denTechnischen
Daten
gibt
den richtigen Lochdurchmesser
fur
lhr
Lautsprechermodell zum Ausschneiden
an.
Die
beiliegende Schablone zeigt ebenfalls
die richtige Ausschneidegr6Be an.
3.
Die
Stellen
fur
die Befestigungsschrauben markieren.
Die
Locher
mit
einer
1/8-Zoll
(3,2
mm)
Bohrerspitze bohren.
4.
Die
Lautsprecherkabel
durch
das
Loch fuhren und
an
den Lautsprecherausgangen
anschlieBen. Beim AnschlieBen
der
Kabel die ordnungsgemaBe Polaririit beachten.
Der
positiveAnschluss des Lautsprechers ist
mit
einem , +"
markiert.
5.
Bei
Modellen
mit
geschlitzten L6chern den Lautsprecher in das Loch einpassen und
die Schrauben in den Schlitzen oben und unten befestigen. Dadurch k6nnen
Sie
den
Lautsprecher so drehen,
dass
die ubrigen Befestigungsl6cher passen. Nach
der
Ausrichtung die Schrauben anziehen.
6.
Die
Schrauben anziehen, bis
der
Lautsprecher eng
an
seinem Platz anliegt,
um
Klappern zu verhindern.
Die
Schrauben
nicht
zu fest anziehen.
HINWEIS:
Falls
erforderlich
die beiliegende
Adapterplatte
bei
der
Befestigung des
Lautsprechers verwenden. Siehe Adapterplatten-Schablonen am Ende
dieserAnleitung.
7
Italiano
&.
ATTENZIONE:
Prima dell'installazione, scollegate
il
terminale
• negative (-) della batteria
per
evitare danni all'unici, pericoli d'incendio
e/o potenziali lesioni personali.
OSSERVATE
LE
REGOLE
DEL
usUONO
SENZA
PERICOLI"
La
costante esposiztone a livel
li
dt
pt-esstone acustica
al
di sopt-a dei I
OOdB
possono causare
Ia
pet-dita pe:-manente dell'udito. I sistemi audio
ad
alta potenza
possono
produrre
livelli
dt
presstone acustica ben superion
ai
130dB.
Si
constglia
il
buon
sensa e l'osset-vanza delle regale del
"suono
senza pericolt"
Considerazioni sull'installazione
Prima
di
iniziare
qualsiasi
operazione
d'installazione, vi
consigliamo
di
seguire
queste
semplici
regale:
I.
Assicuratevi di aver
letto
tutte
le
istruzioni con cura e di averle capite prima di effet-
tuare qualsiasi tentative d'installazione neiconfronti
dell'uniti
2.
Per
motivi
di sicurezza, scollegate
il
cava negative dalla batteria prima di dare l'avvio
all'installazione.
3.
Per facilitare
il
montaggio,
vi
suggeriamo di far scorrere
tutti
i fili prima di montare
Ia
vostra unici. nella
sua
ubicazione.
4.
Usate
connettori
di
alta
qualici.
per
garantire un'installazione che
da
affidamento e
per
ridurre
aJ
minima
Ia
perdita di
segnali
o di potenza.
5.
State attenti prima di trapanare! Cercate di non trapanare e di
non
incidere i serbatoi
della benzina; le
condutture
del carburante, dei freni, del sistema idraulico e a depres-
sione; nonche i fili elettrici quando state lavorando
su
qualsiasi veicolo.
6.
Non
fate mai scorrere i fili
sotto
il veicolo.Avrete
Ia
protezione migliore faccendo
scorrere i fili all'intemo del veicolo.
7.
Evitate di far scorrere i
fili
sopra o attraverso delle estremici. affilate. Usate guamizioni
di tenuta in gamma o in plastica
per
proteggere qualsiasi fila che
passi
attraverso del
metallo,
soprattutto
il
parafiamma
Montaggio
I.
Decidete
dove
montare
gli altoparlanti.Assicuratevi che
sia
un'area abbastanza
grande
per
pater
montare
l'altoparlante a livello e abbastanza
profonda
per
poterlo
collocare
comodamente.
Se
lo
montate
all'interno di
uno
sportello,
controllate
tutte
le funzioni (finestre, serrature, ecc.), una alia volta,
per
assicurarvi che
non
ci siano
ostruzioni.
2.
Fate
riferimento
alia tabella delle specifiche
per
stabilire il
diametro
corretto
del
foro
che
dovrete
praticare
per
il
modello
del
vostro
altoparlante.
II
modello
fornito
anche
da
Ia
dimensione adeguaci del ritaglio.
3.
Marcare le posizioni
perle
viti di montaggio. Praticare i
fori
con una punta da
tra-
pano di 1/8 di pollice (3,2
mm).
4. Passare i cavi del diffusore
tramite
l'apertura e collegarli
ai
terminali.Verificare che
Ia
polarici
sia
corretta
quando
si
collegano i
cavi.
II
terminale
positive del diffusore
e
identificato dal
"+".
5.
Nei
modelli
con
fori
a slot, adattare il diffusore nel
foro
ritagliato e inserire le viti
negli
slot
in alto e in basso. Cosl facendo
si
petrel
ruotare
il diffusore
per
allinearlo
con i rimanenti
fori
di montaggio. Serrare le viti quando
si
e
ottenuto
l'allineamento.
6.
Per evitare
rumore
dovuto
a vibrazioni serrare le viti finche il diffusore
non
sia
salda-
mente
in posizione.
Non
serrare le viti in
modo
eccessivo.
NOTA:
Se
necessaria, della piastra di adattamento in dotazione.Vedere Sagome
per
Ia
piastra di adattamento alia fine del presente manuale.

Fran~ais
Ciblage
du
filtre
T2T-S
I. Voir
le
branchement correct sur !'illustration.
2.
Veillez a
maintenir
Ia
polarite
du
haut-parleur.
3.
Le
branchement
du
fil positifa
Ia
borne 0 dB accorde !'amplitude du tweeter sur celle du
haut-parleur.
4.
Le
branchement
du
fil positifa
Ia
borne -2 dB ou
-4
dB reduit !'amplitude du
tweeter de -2 ou
-4
dB
par rapport a
celle du haut-parleur de medium (ideal lorsque
les
tweeters sont situes
en
haut
des
panneaux de
porte
et
les
haut-parleurs de medium
dans
les
panneaux de seuil).
T252-S &T2652-S
composants
de
ciblage
I. Utiliser !'illustration
pour
une bonne connexion.
2.
Assurez-vous
de
maintenir orateur polarite.
Axis
ON-OFF
I.
Regie
sur
ON
ou OFF match a
Ia
position relative
de
tweeter a
l'auditeur.
Par
defaut
OFF satisfait
Ia
plupart
des
installations.
Switch dB
I.
OdB
correspond a
!'amplitude
(pas
d'augmentation
I
sans
attenuation)
des
le tweeter
au
meme niveau que le milieu de gamme (woofer).
2.
+2dB augmente -2dB
et
reduit !'amplitude de tweeter
en
rapport a
Ia
moyenne gamme,
(ideal
pour
adapter !'installation offset comme
les
tweeters situe
en
haut
des
panneaux
de
porte
et
Midranges faible
en
kick panneaux).
T252-S &T2652-S Bi-Amp Cossover
ciblage
I. Utiliser !'illustration
pour
Ia
connexion
et
assurez-vous
de
maintenir orateur polarite.
2.
Suppression
de
4
vis
de
liaison a
bas
detatch couverture.
3.
BI-AMP Lorsque l'arret d'un amplificateur, utilisez uniquement
''TWT''
input.
4.
Lorsque BI-AMP tension
pour
deux dedies amplificateur, utiliser
les
deux
''TWT''
et
'WFR"
inputs.
Espaiiol
Cableado del
cruce
del
T2T-S
I. Utilice
Ia
ilustracion para hacer
una
conexion correcta.
2.
Asegurese
de
mantener
Ia
polaridad del altavoz.
3.
Conectar
el
cable
positivo a
OdB
hace
que coincida
Ia
amplitud del tweeter con
el
altavoz.
4.
Conectar
el
cable positivo a -2dB o -4dB reduce
Ia
amplitud del tweeter
-2dB o -4dB menos que
Ia
gama
de
medias, (ideal para tweeters situados altos
en
paneles
de puertas y
de
frecuencias
medias
sitiados bajos
en
Ia
placa
de
defensa).
T252-S &
T2652-S
Componente
de
cableado
I. Utilice
Ia
ilustracion para
una
correcta conexion.
2.
Asegurese
de
mantener
Ia
polaridad de los altavoces.
Eje
de
encendido
y
apagado
I.
En
ON
u OFF para que coincida con
Ia
posicion
de
los tweeter
en
relacion con
el
oyente.
Por defecto posicion OFF cumple
Ia
mayorfa
de
las
instalaciones.
dB
I. Coincide con
Ia
amplitud
OdB
(sin
aumento o no
de
atenuacion), de
el
tweeter
en
el
mismo nivel que los
de
gama
media (woofer).
2.
+2B de aumento y -2dB reduce
Ia
amplitud de los
tweeter
en
relacion con
Ia
gama
media, (ideal cuando
se
pongan
en
venta compensar
Ia
instalacion tweeters
de
alta como
situado
en
los
paneles
de
puerta
yen
el
tiro
bajo midranges
paneles).
T252-S
&
T2652-S Bi-Amp Cossover
de
cableado
I. Utilice
Ia
ilustracion para
Ia
correcta conexion y
asegurese
de
mantener
Ia
polaridad
de
los altavoces.
2.
Retire los 4 tornillos
de
Ia
parte inferior
de
cruce detatch a cubrir.
3.
Cuando BI-AMP
apagado
de
un
amplificador, utilice solo
''TWT''
de
entrada.
4.
Cuando BI-AMP encendido durante dos dedicados amplificador,
use
tanto
"TWr'
y
'WFR"
insumos.
8
Deutsch
T2T
-S Crossover-Verkabelung
I.
Zum
ordnungsgemaBen AnschlieBen die Illustration benutzen.
2.
Dabei die Lautsprecherpolaririit beachten.
3.
Das AnschlieBen
des
positiven Drahts
an
0 dB stimmt die Amplitude
des
Hochtoners auf
den Lautsprecher ab.
4.
Das
AnschlieBen
des
positiven Drahts
an
-2dB
oder
-4dB reduziert dieAmplitude
des
HochtOners auf -2dB
oder
-4dB niedriger
als
den Mitteltoner (ideal
fur
Hochtoner, die
sich
hoch
in
Turpaneelen befinden, und Mitteltoner, die
sich
tief im
FuBpaneel
befinden).
T252-S &T2652-S
Komponente
Verdrahtung
I. Verwenden
Sie
fur
die richtigeVerbindung Illustration.
2.
Stell
en
Sie
sicher,
dass
die Aufrechterhaltung Lautsprecher Polaririit.
Axis
ON-OFF-Schalter
I.
Auf
ON
oder
OFF,
urn
Position
der
HochtOner relativ zum Horer.Standard-OFF-Position
entspricht den meisten lnstallationen.
dB-Schalter
I.
Mit
der
Amplitude 0 dB (keine Zunahme
I
keine Dampfung) von
der
Hochtoner auf
der
gleichen
Ebene
wie die Mid-Range-(TT).
2.
+2dbB -2dB
erhoht
und verringert dieAmplitude
der
Hochtoner
in
Bezug
auf die Mid-
Range-,
(ideal, wenn Offset-Installation HochtOner hoch wie inTurverkleidungen und
Mitteltonergering Kick Platten).
T252-S &T2652-S Bi-Amp Cossover
Verdrahtung
I. Verwenden
Sie
fur die richtigeVerbindung Illustration und vergewissern
Sie
sich,
urn
Lautsprecher Polaritat.
2.
Nehmen
Sie
4
Schrauben von unten
nach
Crossover detatch decken.
3.
Bei
der
Bi-Amp ausgeschaltet fur einenVerstarker, verwenden
Sie
nur
''TWT''
Input.
4.
Bei
der
Bi-Amp eingeschaltet
fur
zwei spezielleVersriirker, sowohl
"TWT''
und
'WFR"
Eingange.
Italiano
lmpianto
di
crossover
del
T2T-S
I. Per
il
collegamento
corretto
riferirsi all'illustrazione.
2.
Accertarsi di mantenere
Ia
polarici del diffusore.
3.
II
collegamento del filo del positivo a
OdB
fa
corrispondere l'ampiezza del
tweeter
al
diffu-
sore.
4.
II
collegamento del filo del positivo a -2dB
o-
4dB riduce l'ampiezza del
tweeter
di -2dB
o -4dB
al
disotto del midrange (particolarmente indicato per tweeter posti
in
alto
nei
pannelli della portiera e per midrange posti
in
basso
nel
kick panel).
T252-S
&
T2652-S
Componente
Cablaggio
I.
Usa
illustrazione per
Ia
corretta connessione.
2.
Ricordati di mantenere
Ia
polarici dei diffusori.
Asse
ON-OFF
I. lmpostato
su
ON
o OFF per corrispondenza di posizione rispetto
al
tweeter ascolta-
tore. Default OFF posizione soddisfa
Ia
maggior parte degli impianti.
dB
I.
OdB
corrisponde l'ampiezza (nessun aumento
I
no
attenuazione)
di
il
tweeter e
allo stes-
so livello, come
il
mid-range (woofer).
2.
+2dB aumenta -2dB e riduce l'ampiezza del
tweeter
nella rispetto
al
mid-range, (ideale
quando corrispondenti compensare l'installazione come tweeter situato
in
alto pannelli
porta
e midrange a
basso
contenuto di calcio pannelli).
T252-S &T2652-S Bi-Amp
Wiring
Cossover
I. Usa illustrazione per
Ia
corretta connessione
ed
essere
certi di mantenere
Ia
polarici dei
diffusori.
2.
4 Rimuovere
le
viti
dal
fondo
di
crossover detatch copertina.
3.
Quando BI-AMP spento per un amplificatore, utilizzare solo
''TWT''
input.
4.
Quando BI-AMP attivata per due amplificatore dedicato, l'uso
sia
''TWT''
e
'WFR"
ingressi.

Remove Shaded Area
From Adapter Plate for
T252-S Shallow Mount
Spacer Plate
Adapter Plate Template
6.5" Hole Mounting
Remove Shaded Areas
Mounting for
T252-S 5.25"
9

For 5"x7" Hole Mounting • Remove Dark Shaded Areas
Mounting for
T252-S 5.25"
Remove For Tweeter
Remove Shaded
Areas to Mount
T2652-S 6.5"
10

T252-S
Component System
1.00"
(25mm)
Mounting
Template
'------
T252
-----/
Midrange
Mounting
Holes
5.43"
(138mm)
T252
Midrange
Hole
Cutout
4.81"
(122mm)
II
-----
/
'
/
'
~~/
T2T
'\
I \
/ Tweeter \
I I
1
....
1.
75"
..I
I I
I
(44mm)
I
\ I
'
I
'
/
'
/
-----

T2652-S
Component System
Mounting
Template
/
I
/
/
-----
/ Tweeter
I
\
II
~
-
--
1.75"
~
I
..
,
I
(44mm)
'
/
'
/
'
T2652
___
__,
1.00"
(
25
mm)
Midrange
Mounting
Holes
6.18"
(157mm)
_
__,
T2652
Midrange
Hole
Cutout
5.57"
(141
mm)
-
~
-
---
=-
-----
:)--
-
12

LIMITED
WARRANTY
STATEMENT
Rockford Corporation offers a limited warranty
on
Rockford Fosgate products on
the
following terms:
Length
ofWarranty
Speakers-
IYear.
Any
Factory
Refurbished
Product-
90 days
(receipt
required)
What
is
Covered
This warranty applies only
to
Rockford Fosgate products sold
to
consumers
by
Authorized Rockford Fosgate
Dealers
in
the
United States ofAmerica
or
its possessions. Product purchased
by
consumers from an
Authorized Rockford Fosgate Dealer
in
another country are covered only
by
that
country's Distributor and
not
by
Rockford Corporation.
Who
is
Covered
This warranty covers only
the
original purchaser of Rockford product purchased from an Authorized
Rockford Fosgate Dealer
in
the
United States.
In
order
to
receive service,
the
purchaser must provide
Rockford with a copy
of
the
receipt stating
the
customer name, dealer name, product purchased and date
of
purchase. Products found
to
be
defective during
the
warranty period
will
be repaired
or
replaced
(with a product deemed
to
be equivalent)
at
Rockford's discretion.
What
is
Not
Covered
I.
Damage caused
by
accident, abuse, improper operations,water, theft, shipping
2.Any
cost
or
expense related
to
the
removal
or
reinstallation
of
product
3.
Service performed
by
anyone
other
than Rockford
or
an Authorized Rockford Fosgate Service
Center
4.Any product which
has
had
the
serial number defaced, altered,
or
removed
5.
Subsequent damage
to
other
components
6.Any product purchased outside
the
U.S.
7.Any product
not
purchased from an Authorized Rockford Fosgate Dealer
Umit
on
ImpliedWarranties
Any
implied
warranties
including
warranties offitness for use and merchantability are limited
in
duration
to
the
period ofthe express warranty set forth above. Some
states
do not allow limitations on the length of
an
implied
warranty, so this limitation
may
not
apply.
No
person
is
authorized
to
assume for Rockford Fosgate
any
other
liability
in
connection
with
the sale
of
the product.
How
to
Obtain Service
Contact
the
Authorized Rockford Fosgate Dealer you purchased this product from.
If
you need further
assistance,
call
1-800-669-9899 for Rockford
Customer
Service.
You
must obtain an
RA#
(Return
Authorization
number)
to
return any product
to
Rockford Fosgate.
You
are responsible for shipment
of
product
to
Rockford.
E.U
Warranty
This product meets
the
current
EU
warranty requirements, see yourAuthorized dealer for details.
Rockford
Fosgate
Rockford
Corporation
600
South Rockford Drive
Tempe,Arizona 85281 U.S.A.
In
U.S.A., [phone]
-Customer
Service 1-800-669-9899
www.rockfordfosgate.com
Designed
and
Engineered
by
Rockford
Fosgate,
Tempe,AZ.
USA.
©20
I0 Rockford
Corporation.
All
rights reserved.
Rockford Fosgate and
the
Rockford Fosgate logo
are
either
05/2009 B.M. registered
trademarks
or
trademarks
of
Rockford
Corporation.
11/2009
E.R.
(WebWizard)
1230-56187-0I Printed
in
China