RODE Microphones NTH-100 User manual

USER GUIDE & SUPPORT
The RØDE NTH 100 professional over - ear headphones offer exceptional sonic performance and superior comfort that inspires
creativity . Featuring custom - matched drivers that deliver an incredibly accurate frequency response and ultra - low distortion , and a
precision - engineered acoustic design optimised for exceptional detail and clarity , they are ideal for all forms of content creation ,
including music production , mixing and audio editing , podcasting , streaming and location recording .
Find out all you need to know about using your NTH 100 s here .
Contents
Features
1 Removable  Alcantara ® headband cushion
NTH -100 / USER GUIDE & SUPPORT

EN
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Rode NTH-100 o cerca il
tuo prodotto tra le migliori offerte di Cuffie e Microfoni

2
FitLok ™ locking tab
Twist to lock and unlock headband size adjustment
3 Ergonomic earcup shape
4
Right cable attachment socket
Push plastic cable bayonet into place and turn clockwise to lock
5 Headband cushion locking tabs
Slide locking tabs down on either side to release
6 Red indicator for right earcup
7 Removable Alcantara ® ear cushion
Pull to remove
8 Left cable attachment socket
Use included rubber seal to close unused socket
Getting Started: Cable Plug Identi cation
The cable supplied with your NTH 100 s features a different type of connector on each end . Insert the jack plug with the
plastic bayonet connector and lock symbol into the headphone earcup . Insert the jack plug with the gold - plated thread
into your audio source . If you experience intermittent or crackly audio , check that the cable is attached correct way
round .
NTH -100 / USER GUIDE & SUPPORT

Connecting the Cable to the Headphones
To connect the cable to the headphone earcup , simply insert the plastic bayonet end into the socket and twist the
connector clockwise to lock it into place . To remove it , simply twist counter - clockwise to unlock and pull free .
The NTH 100 s feature cable attachments on both earcups , allowing you to connect the cable where is most convenient .
Connecting the Headphones to your Device
The supplied cable comes with a standard 3.5 mm jack plug for connecting to devices with a 3.5 mm output , such as a
smartphone . Also included is a 1/4- inch to 3.5 mm adaptor for connecting to professional audio equipment , such as mixers
and audio interfaces . This screws securely onto the end with the gold - plated thread .
NTH -100 / USER GUIDE & SUPPORT

Pro Tip
The NTH 100 s are a low - impedance , high - sensitivity headphone , which means they can be used with virtually any
equipment . This may mean a low volume setting on your amplifier could result in a loud signal – so turn down your
volume to zero before plugging in the headphones , and then gradually raise the volume to the desired level .
Using the Rubber Seal
Included in the accessory pack is a rubber seal for closing off the earcup socket that is not in use . We recommend using
this at all times . Not only will it prevent dirt and debris entering the socket , but it also ensures that the frequency
response is perfectly matched between left and right earcups for critical monitoring .
NTH -100 / USER GUIDE & SUPPORT

Using the COLOR ID Rings
The NTH 100 s come with a set of eight COLOR ID rings . These can be used for quick identification in setups where
multiple pairs of headphones are in use . To use them , remove the black ID ring that clips around the body of the plugs at
either end of the cable , and replace it with your preferred colour . Note that the colours match the channel ID colours used
by the RØDECaster Pro and RØDE Connect .
NTH -100 / USER GUIDE & SUPPORT

Using the FitLok ™ Locking System
The FitLok ™ system allows you to set the NTH 100 headband size to your preferred comfort setting , and then lock this in
place , meaning you never have to adjust it again . To unlock the headband adjustment , twist the locking cams clockwise .
The earcups will now slide freely , allowing you to set them to your preferred position . Once you are comfortable , simply
turn the cams counter - clockwise to lock the earcups into place
NTH -100 / USER GUIDE & SUPPORT

Pro Tip
You can unlock and lock the Fitlok ™ adjustment whilst wearing the NTH 100 s for the optimal fit – perfect for long hours of
content creation .
Earpad and Headband Cushion Removal and Cleaning
To remove the earpads from the headphones , simply pull them away from the earcup . To replace , push them back into
place , working around the perimeter to ensure all the tabs are locked into place .
To remove the headband pad , slide the locking tabs on either side of the earpad away from the pad . You may need to
push the locking tab from underneath to facilitate this . Pull off the lower cushion ( held in place by Velcro ), and then slide
off the upper one . To replace , reverse the steps , ensuring that the locking clips are correctly positioned over the top of
the ends of the cushions before sliding them into place , then make sure they click as they lock into position .
To clean the pads , simply wipe with a damp cloth . Do not immerse the pads in water , or use leather or suede cleaning
products , as this may damage the pad . Replacement pads are available – please contact our service centre if you need
new pads .
NTH -100 / USER GUIDE & SUPPORT

Products
Microphones
Headphones
Interfaces and Mixers
Accessories
Apps
Apparel
Support
Contact RØDE
Service Centre
Warranty
Where to Buy
Authorised Dealers
Company
About RØDE
News and Info
Job Opportunities
Account
Manage your Account
Create Account
Subscribe to our latest news and offers
Subscribe
NTH -100 / USER GUIDE & SUPPORT

Privacy Policy
|
Terms & Conditions
  
© 2023 RØDE All Rights Reserved .
NTH -100 / USER GUIDE & SUPPORT