Rogers 410673 User manual

0
Product Information Packet
Product Name: Portable Goal Post
Product Part Numbers: 410673 & 410674

1
Table of Contents
Introduction……………………………………………………………………………….……..……………….…
General Safety Rules…………………………………………………………………….…..……………….…..
Symbols……………………………………………………………………………………..…………………...…
Technical Specifications………………………………………………………………………………………….
Assembly Instructions……………………………………………………………………………………………..
Maintenance…………………………………………………………………………..……………………….…..
Customer Service Information………………………………………………………..……..…..……...……….
Introduction
The Rogers Athletic Portable Goal Post has been designed and manufactured with safety, performance and
dependability as top priorities, as well as making it easy to operate and maintain.
The care you give your Goal Post will greatly determine your satisfaction with its performance and service life.
We urge careful study of this manual to provide you with a thorough understanding of your new Goal Post
before operating, as well as suggestions for operation and maintenance.
If your manual becomes lost or destroyed, Rogers Athletic will gladly provide you with a new copy. Should you
require additional information or assistance, please feel free to contact us.
BECAUSE ROGERS ATHLETIC MAINTAINS AN ONGOING PROGRAM OF
PRODUCT DEVELOPMENT AND IMPROVEMENT, WE RESERVE THE RIGHT
TO MAKE IMPROVEMENTS IN DESIGN OR CHANGES IN SPECIFICATIONS
WITHOUT INCURRING ANY OBLIGATIONS TO INSTALL THEM ON UNITS
PREVIOUSLY SOLD.
1
2
3
4
5
8
8

2
General Safety Rules
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below may result in serious personal
injury.
SAVE THESE INSTRUCTIONS
Use field equipment in a supervised environment with proper gear.
Inspect equipment prior to use. DO NOT use if it appears damaged or inoperable. NOTE: to
avoid damage to equipment, disassemble the Portable Goal Post if winds over 30mph are expected.
Save these instructions. Refer to them frequently and use them to instruct others who may use the
goal post. If you loan someone your goal post, loan them these instructions also.
Read the Product Information Packet. Failure to read this packet is considered a misuse of this
equipment.
Become familiar with all caution and warning decals affixed to the field equipment before use.
Never cover or deface caution/warning labels.

3
Symbols
Read the Product Information Packet: To reduce risk of
injury, user must read and understand Product Information
Packet before using this product.
Do Not Climb Symbol: Climbing on or playing around
equipment may result in personal injury.
Safety Alert: Precautions that involve your safety.

4
Rogers Athletic Field Equipment Specifications
Portable Goal Post
Portable Goal Post Construction, Finish, and Hardware
- Constructed of aluminum schedule 40 pipe.
- Raw Aluminum.
- Zinc-plated hardware.
H
W D
23’4”
Weight: 325 lbs
Height: 20’ 5”
Width: 24’ 11/16” (23’4” inside uprights)
Depth: 11’ 4”
18’6”
Weight: 298 lbs
Height: 20’ 5”
Width: 24’ 11/16” (18’6” inside uprights)
Depth: 11’ 4”
- Use during practice and at temporary fields.
- All aluminum construction.
- Easy disassembly.
- Can be moved while assembled.

5
1
2
Begin by installing wheels on the lower elbow connections as shown with 9” axle bolts, washers and nuts.
Use a ¾” wrench to tighten, but do not over tighten – the wheel should roll freely. Also loosely thread the 1”
pinch bolts into the elbows.
Assembly
Install upright T-connectors to ends of crossbar. Finger tighten pinch bolts.
Crossbar length = 23’ 3” or 18’5”

6
3
4
Slide the upright tubes through the T-connectors of the crossbar without tightening pinch bolts so you can
set the height later. Also slip the wheeled elbow over the bottoms of the upright tubes, as shown.
Fit remaining elbow connectors (no wheel brackets) to the base cross bar and base outrigger tubes. Do not
tighten the pinch bolts until the entire goal post is built.
Upright tubes are 20’ long
Crossbar length = 23’ 3” or 18’5”
Outrigger length = 10’

7
5
Fit the base assembly to the upright assembly with the uprights lying on the ground. All elbow connectors
can now be tightened. (3/4” wrench) Adjust height of crossbar before tightening. Dimension from base of
elbow connector (what would be ground level when the goal post is upright) to the bottom edge of the T-
connectors should be 9 feet. Once all bolts are ti
g
htened the
g
oal
p
ost ma
y
be fli
pp
ed u
p
ri
g
ht.
9 feet

8
Maintenance
WARNING!
READ AND UNDERSTAND ALL MAINTENANCE PROCEDURES.
Failure to follow all procedures listed below may cause serious injury and/or
decrease equipment functionality.
Frequently check to see that all bolts are securely fastened.
Field equipment should be washed periodically with soapy water to maintain original surface
finish.
Replace any damaged equipment with genuine Rogers Athletic parts. Failure to do so may result
in unsafe equipment and/or personal injury.
Customer Service
For parts or service contact Rogers Athletic Company. When ordering parts be sure to provide all relevant
information available including the name and part number of the equipment purchased. This information is
located on the cover of this product information package. Customer service are Monday through Friday from
8:00 a.m. to 5:00 p.m. Eastern Standard Time. Customers can phone [phone] or toll free at (800) 248-
0270. Fax toll free at [phone] or mail to:
Rogers Athletic Company
3760 W. Ludington Drive
Farwell, MI 48622

9
Rogers Athletic Company
3760 N. Ludington Drive
Farwell, MI 48622
www.rogersathletic.com
[phone]
[phone]
Fax toll free [phone]
PIP410673