Rogue4 S6-RGB User manual

HIGH PERFORMANCE LED LIGHTING
INSTALLATION MANUAL

THANK YOU FOR YOUR ROGUE4PURCHASE.
PRELIMINARY STEPS
1. Read all instructions carefully and study diagrams before installing lights.
2. Check with state and local authorities for laws governing usage and proper
mounting of auxiliary lamps.
3. Disconnect ground connection from battery (marked “-“) to avoid accidental short
circuits before attempting to connect electrical wires.
4. Route new wires along existing wiring. Tape as necessary to correct slack.
5. When running wires, keep them away from moving parts.
WIRING INSTRUCTIONS
1. Mount switch in a convenient location where it is easily reached from the driver’s
seat.
2. Wiring: Red “+”, black “-”. Attach the Red wire terminal to positive side “+” ,
and the black wire terminal to negative side “-” on battery or ground. (Vehicles)
3. Make sure the working voltage (DC12V/24V), choose the corresponding relays.
(DC12V/24V)
4. Insert the lamp connector (A) to wiring connector (B)
5. Turn on the switch to make sure if the lamp works. If not, please check carefully if
the wiring installing correct.
CAUTION
- Only operate under the specified voltages (DC9-30V)
- This light becomes hot during continuous use. Don’t remove the lamp or
touch the casing for at least 30 minutes after turning the lamp off.
- Keep heat-sink clean and exposed to maintain air flow.

POWER
RGB
RGB Controller required for full color control
Black (power)Red (negative)
Green (negative)Blue (negative)
MOUNTING LIGHTS
Installation Method Using L bracket Mounts
1. Install the side mount on the lamps and fasten with bolts.
2. Drill M8 bolt holes at the appropriate position of the mounting plate where you
would like to fix the base and attach the mounting plate.
Installation Method Using Pipe Mount Adapters
1. Install the side mount on the lamps and fasten with bolts.
2. Attach the clamps onto the roll bar/pipe/tube.
3. Insert the bolt through the clamp, mount, and roll bar then tighten it.
WIRING
Mounting Lights
Installation Method Using L bracket Mounts
1.Install the side mount on the lamps and fasten with bolts.
2.Drill M8 bolt holes at the appropriate position of the mounting plate where
you would like to fix the base and attach the mounting plate.
Installation Method Using Pipe Mount Adapters
1.Install the side mount on the lamps and fasten with bolts.
2.Attach the clamps onto the roll bar/pipe/tube.
3.Insert the bolt through the clamp, mount, and roll bar then tighten it.
23
Mounting Lights
Installation Methods
1. Install the side mount on the lamps and fasten with bolts.
2. Drill M8 bolt holes at the appropriate position of the mounting plate where
you would like to fix the base and attach the mounting plate.
Installation Methods (II)
1.Install the side mount on the lamps and fasten with bolts.
2.Attach the clamps onto the roll bar/pipe/tube.
3.Insert the bolt through the clamp, mount, and roll bar then tighten it.
Mounting Lights
Installation Method Using L bracket Mounts
1.Install the side mount on the lamps and fasten with bolts.
2.Drill M8 bolt holes at the appropriate position of the mounting plate where
you would like to fix the base and attach the mounting plate.
Installation Method Using Pipe Mount Adapters
1.Install the side mount on the lamps and fasten with bolts.
2.Attach the clamps onto the roll bar/pipe/tube.
3.Insert the bolt through the clamp, mount, and roll bar then tighten it.
23
Mounting Lights
Installation Methods
1. Install the side mount on the lamps and fasten with bolts.
2. Drill M8 bolt holes at the appropriate position of the mounting plate where
you would like to fix the base and attach the mounting plate.
Installation Methods (II)
1.Install the side mount on the lamps and fasten with bolts.
2.Attach the clamps onto the roll bar/pipe/tube.
3.Insert the bolt through the clamp, mount, and roll bar then tighten it.

MOUNTING LIGHTS
Installation Method 1
1. Install the side mount on the lamps and fasten with bolts.
2. Drill M8 bolt holes at the appropriate position of the mounting plate where you
would like to fix the base and attach the mounting plate.
Installation Method 2
1. Install the side mount on the lamps and fasten with bolts.
2. Attach the clamps onto the roll bar/pipe/tube.
3. Insert the bolt through the clamp, mount, and roll bar then tighten it.
Mounting Lights
Installation Method Using L bracket Mounts
1.Install the side mount on the lamps and fasten with bolts.
2.Drill M8 bolt holes at the appropriate position of the mounting plate where
you would like to fix the base and attach the mounting plate.
Installation Method Using Pipe Mount Adapters
1.Install the side mount on the lamps and fasten with bolts.
2.Attach the clamps onto the roll bar/pipe/tube.
3.Insert the bolt through the clamp, mount, and roll bar then tighten it.
23
Mounting Lights
Installation Methods
1. Install the side mount on the lamps and fasten with bolts.
2. Drill M8 bolt holes at the appropriate position of the mounting plate where
you would like to fix the base and attach the mounting plate.
Installation Methods (II)
1.Install the side mount on the lamps and fasten with bolts.
2.Attach the clamps onto the roll bar/pipe/tube.
3.Insert the bolt through the clamp, mount, and roll bar then tighten it.
Mounting Lights
Installation Method Using L bracket Mounts
1.Install the side mount on the lamps and fasten with bolts.
2.Drill M8 bolt holes at the appropriate position of the mounting plate where
you would like to fix the base and attach the mounting plate.
Installation Method Using Pipe Mount Adapters
1.Install the side mount on the lamps and fasten with bolts.
2.Attach the clamps onto the roll bar/pipe/tube.
3.Insert the bolt through the clamp, mount, and roll bar then tighten it.
23
Mounting Lights
Installation Methods
1. Install the side mount on the lamps and fasten with bolts.
2. Drill M8 bolt holes at the appropriate position of the mounting plate where
you would like to fix the base and attach the mounting plate.
Installation Methods (II)
1.Install the side mount on the lamps and fasten with bolts.
2.Attach the clamps onto the roll bar/pipe/tube.
3.Insert the bolt through the clamp, mount, and roll bar then tighten it.

LIMITED LIFETIME WARRANTY
WHAT THIS WARRANTY COVERS
This is a “Limited” warranty. This warranty covers any defects in materials and
workmanship and warranty only applies to the original purchaser and is not
transferable. This warranty is also only valid if the original purchase was made from
an authorized Rogue 4 dealer.
HOW LONG COVERAGE LAST
From date of purchase to 1 year - Rogue 4 will fix or replace the product. The customer
is responsible for shipping charges to Rogue 4 for repair of the product. Rogue 4 will
cover all parts, labor and return shipping to the customer. After 1 year - The customer
is responsible for all shipping charges to Rogue 4 for repair of the product and labor.
WHAT IS NOT COVERED
This warranty does not cover fading or discoloration caused by exposure to sunlight
or chemicals such as ammonia, household bleach, or any cleaning material that
contains abrasive substances. Rogue 4 does not cover the cost for removal and re-
installation of any kind. This warranty is void and inapplicable if Rogue 4 deems that
the product was abused or misused; including but not limited to damage caused
by accident, mishandling, improper installation, negligence, normal wear and tear,
excessive water or heat damage, freight damage or products that have been altered
in any way. Product owned by anyone other than the original purchaser from an
authorized Rogue 4 dealer. (The warranty is not transferable and will not apply to
products purchased from unauthorized dealers.) Rogue 4 is not responsible for any
damages to a consumer’s vehicle or person from a product failure. The warranty is
void if Rogue 4 deems the product was installed or used improperly. Rogue 4 shall
not be responsible for any incidental or consequential damages, except to the extent
provided (or prohibited) by applicable law. This warranty gives you specific legal
rights, and you may also have other rights which vary from state.
HOW TO OBTAIN WARRANTY SERVICE
Contact Rogue 4 either by phone at 855-476-4834 or by email at warranty@rogue-4.
com. A service representative will assist you in the necessary actions to verify that the
problem that you are experiencing is covered under warranty. If it is in fact a warranty
issue, Rogue 4 will issue an RA number for tracking purposes and give instructions
on sending the product in for evaluation.
INTERNET WARNING
Rogue 4 products sold on any non authorized web site or internet auction site are void
of any and all manufacturer’s warranty. Please contact Rogue 4 at 855-476-4834
or visit our web site at www.rogue-4.com to search for an authorized site and/or an
authorized retailer near you.

SIGMA SERIES SINGLE ROW LED RGB LIGHTBARS
D6D6
S6
DEPTH 3.4” HEIGHT 2.2”
BAR WIDTH 6.77” MOUNT BOSS WIDTH 7.4” BRACKET WIDTH 8.19”
S10
DEPTH 3.4” HEIGHT 2.2”
BAR WIDTH 10.71” MOUNT BOSS WIDTH 11.34” BRACKET WIDTH 12.13”
S20
DEPTH 3.4” HEIGHT 2.2”
BAR WIDTH 20.55” MOUNT BOSS WIDTH 21.18” BRACKET WIDTH 21.97”
S30
DEPTH 3.4” HEIGHT 2.2”
BAR WIDTH 30.39” MOUNT BOSS WIDTH 31.02” BRACKET WIDTH 31.81”
S40
DEPTH 3.4” HEIGHT 2.2”
BAR WIDTH 40.24” MOUNT BOSS WIDTH 40.87” BRACKET WIDTH 41.66”
S50
DEPTH 3.4” HEIGHT 2.2”
BAR WIDTH 50.08” MOUNT BOSS WIDTH 50.71” BRACKET WIDTH 51.5”
Available in Black or White
Sigma 30 shown >
BAR WIDTH
MOUNT BOSS WIDTH
BRACKET WIDTH

DELTA SERIES DOUBLE ROW LED RGB LIGHTBARS
D6s6
D6
DEPTH 3.53” HEIGHT 3.23”
BAR WIDTH 6.93” MOUNT BOSS WIDTH 7.56” BRACKET WIDTH 8.35”
D10
DEPTH 3.53” HEIGHT 3.23”
BAR WIDTH 10.94” MOUNT BOSS WIDTH 11.57” BRACKET WIDTH 12.36”
D20
DEPTH 3.53” HEIGHT 3.23”
BAR WIDTH 20.98” MOUNT BOSS WIDTH 21.61” BRACKET WIDTH 22.4”
D30
DEPTH 3.53” HEIGHT 3.23”
BAR WIDTH 31.02” MOUNT BOSS WIDTH 31.65” BRACKET WIDTH 32.44”
D40
DEPTH 3.53” HEIGHT 3.23”
BAR WIDTH 41.06” MOUNT BOSS WIDTH 41.69” BRACKET WIDTH 42.48”
D50
DEPTH 3.53” HEIGHT 3.23”
BAR WIDTH 51.1” MOUNT BOSS WIDTH 51.73” BRACKET WIDTH 52.52”
Available in Combo or Spot Beam congs
Delta 30 shown >

ROGUE 4.COM / 877-938-7757