Ronbow Signature series Assembly instructions

INSTALLATION AND CARE GUIDE
29” PEBBLE VANITY AND SINKTOP/LED MIRROR
E062629
E062730

161013ronbow.eu | ronbow.comINSTALLATION SHEET
1
PEBBLE 29” Vanity and Sinktop/LED Mirror
Model : E062629
E062730
Designed By: ORA ITO | FRANCE
Tools Required
PRE-INSTALLATION
Materials Included
E062629
3 long screws
3 washers
1 wrench
E062730
4 long screws
1 set of cleats
Materials Required
2 2x4 beam cut to size
ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENSED ELECTRICIAN.
WARNING: To reduce the risk of electrical shock, shut o power before wiring the cabinet.
CAUTION: Requires 120V 20AMP circuit.
CAUTION: The LED mirror must be wired to a GFI (ground fault interrupter) circuit breaker when used in
bathrooms and all other locations required by the national electric code.
120VAC
20A GFI
CIRCUIT BREAKER FIELD CONNECTION LED MIRROR CABINET
White = Negative
Green= Ground
Black= Positive
White = Negative
LED
Black= Positive
Green= Ground

161013ronbow.eu | ronbow.comINSTALLATION SHEET
2
PEBBLE 29” Vanity and Sinktop/LED Mirror
Model : E062629
E062730
Designed By: ORA ITO | FRANCE
Figure 1.
Step 2: Cut a rough opening for the electrical
box and run the wires from the house
to the electrical box.
Step 3: Mark pilot holes for the long screws to
fasten them into the studs.
Fasten the vanity to the wall.
Verify the vanity is level.
Determine the ideal location of your
new wall cabinet.
It is recommended that the vanity is
between the height of 30” - 32”.
Measure the distance from the vanity
top to the wall cleat.
NOTE: Check if the location has at
least two studs. Front notch the studs
to fit a 2x4 beam for added stability of
the wall cabinet.
See Figure 1.
Step 1:
INSTALLATION
Step 4: The drawer system is ran by electric.
It is recommended to install an outlet
at the bottom electric box.
Figure 2.
See Figure 2.
2x4 beam
2x4 beam

161013ronbow.eu | ronbow.comINSTALLATION SHEET
3
PEBBLE 29” Vanity and Sinktop/LED Mirror
Model : E062629
E062730
Designed By: ORA ITO | FRANCE
Figure 3.
Figure 4.
Step 5:
Step 6:
Step 7:
Install the faucet and drain per the
manufacturer’s instructions.
Measure the distance of the wall cleat
and mark the locations on the wall.
Drill pilot holes into the studs.
Take the measurements from step 1
and secure the wall cleat to the wall.
Make sure to secure the wall cleat over
the horizontal beam.
Attach the wires in the electrical box.
See Figure 3.
See Figure 4.

161013ronbow.eu | ronbow.comINSTALLATION SHEET
4
PEBBLE 29” Vanity and Sinktop/LED Mirror
Model : E062629
E062730
Designed By: ORA ITO | FRANCE
Step 8: Clean the top surface of the vanity and
apply a thin bead of silicone around
the surface where the sink will sit.
Figure 5.
Step 9: Carefully lift and sit the sink and mirror
over the wall cleat and onto the vanity.
See Figure 5.

161013ronbow.eu | ronbow.comINSTALLATION SHEET
5
PEBBLE 29” Vanity and Sinktop/LED Mirror
Model : E062629
E062730
Designed By: ORA ITO | FRANCE
Wood Surfaces
Recommended Products
The fine furniture finish of your new vanity, mirror or other bathroom accessories are designed to
protect against normal home use. With proper care, your product will provide years of use and beauty
in your home.
General Care Tips
PRODUCT CARE AND MAINTENANCE
• If a spill occurs, clean and dry the surface immediately as liquid can soak through the surface and cause
greater damage.
• Do not place in direct sunlight. Exposure to sunlight may affect the appearance of your vanity, and the
finish will eventually crack.
• Keep away from direct sources of extreme temperatures as heat, cold or moisture from humidity.
Color changes, or blemishes in the wood can occur if recommended care of is not met. Try to avoid
these extremes.
• Most wood surfaces can be cleaned, or dusted, with any commercial wood cleaning product. For general
cleaning, use a non-abrasive, or lint-free cloth while dusting along the wood grain to preserve the
wood’s chacteristics.
• Pledge Orange Oil, or similar
• Orange-Glo Wood Cleaner
DISCLAIMERS: Wood naturally ages, darkens and changes color over time due to several environmental conditions that may cause materials to vary from their
original color and/or to warp, split or crack. These variations are considered to be the nature of the material in relation to their environmental exposure and may
be significant over a long period of time. The eectiveness of cleaning Ronbow product is dependant on various factors that include sunlight, smoke, moisture,
household cleaners and/or amount of cleaning product used over time. Ronbow cannot guarantee that the above Product Care & Maintenance methods will
eectively clean your product.
• Test cleaning product on small, discrete area prior to applying to entire surface.
• Wipe surfaces frequently with dry, soft, non-abrasive and lint-free towel.
• Do not allow liquids and moisture to accumulate on the surface of products.
• For warranty information, please visit our website at www.ronbow.com or contact the Customer Service
Department at [phone].

161013ronbow.eu | ronbow.comINSTALLATION SHEET
6
PEBBLE 29” Vanity and Sinktop/LED Mirror
Model : E062629
E062730
Designed By: ORA ITO | FRANCE
Recommended Products
Solid Surface Sinks
• Propietary Bathroom Cleaning Products
DISCLAIMERS: Eectiveness of cleaning your Ronbow products is dependent on various factors that include: water temperature, concentration and/or
amounts of cleansers. Because of these many dierent conditions, Ronbow cannot guarantee that the above Product Care & Maintenance methods will
eectively clean your product.
• After applying recommended cleaning products, wipe surfaces clean and rinse completely with water
immediately
• Use mild cleaning solution only, Strong, abrasive cleaners are not recommended, and can damage surface.
Do not allow cleaner to soak.
• Use a soft, dampened sponge or cloth. Never use an abrasive materials such as a brushed or scouring pad
to clean surface.
• Always test your cleaning solution on a inconspicuous area before apply to the entire surface.
• Hot pans, electric frying pans, waffle irons, crock-pots, and other heat-generating appliances can damage
the surface. To prevent heat damager, always use a trivet with rubber feet between the appliance and the
countertop.
• Avoid exposing solid surface to strong chemicals, such as paint removers, oven cleaner, ect. If contact
occurs, quickly flush the surface with water.
• Remove nail polish with a non-acetone-based nail polish remover and flush with water.
• Do not cut directly on your solid surface countertop. Cutting directly on it will damage the surface.
• Run cold water when pouring boiling water into sinks
• Soapy water and a sponge will remove most stains. Do not use 409 or Fantastik.
• For more stubborn stains use a blue scotch-brite pad and Soft-Scrub.

161013
40650 Encyclopedia Circle
Fremont, CA 94538
T 510.713.1188
F 510.657.9388 ronbow.eu | ronbow.com