Rosewill RNX-AC600NUB User manual

User Manual
RNX-AC600NUB
Nano USB Wireless Adapter

3
Nano USB Wireless Adapter User Manual
RNX-AC600NUB
Chapter 1: Introduction………….....................………...…….… 03
1.1 Product Features…………………………………….…............ 03
1.2 Package Contents………………………………….........…...... 03
1.3 Indicator Description……………………………………........... 03
CHAPTER 2: Quick Installation Guide……………...……......... 04
2.1 Driver Installation………………………......................…......... 04
2.2 Connect to Wireless Access Point……………....................... 07
2.2.1 Using Client Utility……………………………………............ 07
2.2.2 Using Windows Zero Configuration…………………........... 11
CHAPTER 3: Client Utility………………………………….......... 16
3.1 Connection Profile Management………………………........... 16
3.1.1 Add a new profile……………………………………….......... 17
3.1.2 Remove an existing profile…………………………….......... 19
3.1.3 Edit an existing profile………………………………............. 19
3.1.4 Make a copy of existing profile…………………….............. 20
3.1.5 Set as default profile…………………………………............ 20
3.2 View Network Statistics, General Information, and Status.... 21
3.2.1 General Information………………….................................. 21
3.2.2 Status………………………………………………....…......... 22
3.2.3 View Network Statistics………………………….....……...... 22
3.3 Miscellaneous Settings……………………………......……..... 23
3.4 Establish secure connection with AP by WPS…………........ 24
3.4.1 PIN Code……………………................................……….... 26
3.4.2 Push Button…………………………...........................…..... 27
CHAPTER 4 Soft AP Function………………………….............. 28
4.1 Switch to AP Mode and Station Mode………………….......... 28
4.1.1 Configure SSID and Channel…………………………......... 30
4.1.2 Setup Soft-AP Security…………………………................... 31
4.2 Advanced Settings……………………………………….......... 32
4.3 Wireless Statistics………………………………….................. 33
4.4 Internet Connection Sharing (ICS)…………………............... 34
CHAPTER 5: Troubleshooting………………………….............. 35
Chapter 1: Introduction
1.1 Product Features
•
Complies with IEEE 802.11ac , IEEE 802.11a,IEEE 802.11n,IEEE 802.11g and
IEEE 802.11b standards
•
Provides USB2.0 port
•
Provides 150/433Mbps receiving rate and 150/433Mbps sending rate
•
Supports 20MHz/40MHz/80MHz frequency width
•
Auto-detects and changes the network transmission rate
•
Provides two work modes: Infrastructure and Ad-Hoc
•
Supports Soft AP to establish your wireless LAN networking
•
Supports 64/128-bit WEP, WPA, WPA2 encryption methods and 802.1x
security authentication standard
•
Supports WPS (Wi-Fi Protected Setup) encryption method to free you from
remembering long passwords
•
Easy-to-install, plug and play
•
Supports Windows XP/VISTA/Win7/ Win8/Win10/Linux/Macintosh
Thank you for purchasing the wireless 802.11b/g/n/a/ac USB adapter!
This adapter is mini size design and you are able to plug it into the USB port.
Excepting common wireless standards 802.11b/g/n, this wireless adapter is also
802.11ac compatible - data transfer rate is 150/433Mbps, and that’s three times
faster than 802.11g wireless network!
1.2 Package contents
The following contents should be found in your box:
•
One Wireless 802.11b/g/n/a/ac USB adapter
•
One CD (include driver/utility/user manual)
•One Quick Installation Guide
1.3 Indicator Description
There is a LED indicator blinking when data communication is going on.
Table of Contents

4 5
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
2.1.3
Insert the driver CD into your CD-ROM. You can see autorun screen below. if
not, you can double click ‘autorun.exe’ on CD.
CHAPTER 2: Quick Installation Guide
This chapter is to assist you how to use the included CD-ROM which
comprises the Driver and the Client Utility Interface.
2.1 Driver Installation
Please follow the following instructions to install your new wireless USB
Adapter:
2.1.1
Insert the USB wireless network card into an empty USB 2.0 port of your
computer when computer is switched on. Never use force to insert the card, if
you feel it’s stuck, flip the card over and try again.
2.1.2
The following message will appear on your computer, click ‘Cancel / Close’.
Under Windows XP
Under Windows Vista and Windows 7
Click ‘Install Driver’ to start the installation procedure
2.1.4
Installation descriptions shown. Click ‘Next’ to continue

6 7
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
2.2 Connect to Wireless Access Point
To use wireless network, you have to connect to a wireless access point first.
You can either use Client utility (comes with network card driver), or Windows
Zero Config utility (comes with Windows operating system).
2.1.5
Once the installation is finished the computer will be asked to reboot. You can
click ‘Finish’ and reboot the computer to finish the installation of driver files.
2.1.6
A new icon will appear near the clock of system tray:
Left-click the icon will launch wireless network configuration utility, and you can
right-click the icon to show the quick menu of configuration utility. This icon also
uses different color to show the status of wireless connection:
Wireless connection is established, good signal reception.
Wireless connection is established, weak signal reception.
Connection is not established yet.
Wireless network card is not detected.
For detailed instructions of wireless network configuration utility,
please see next chapter.
2.2.1 Using Client Utility
1. Please follow the following instructions to use Client configuration utility to
connect to wireless access point.
Left-click the Client configuration utility icon located at lower-right corner of
computer desktop, and configuration menu will appear:
HERE!
2. Wireless utility will appear. Click ‘Available Network’ menu to search for
wireless access points nearby.

8 9
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
3. Please wait for a while, and all wireless access points which can be reached
by this wireless network card will be displayed here.
If the wireless access point you wish to connect does not appear here, you
can click ‘Refresh’ button to scan for wireless access points again; if the wireless
access point you’re looking for still not appear, try to move the computer closer.
When the access point you’re looking for is on the list, left-click it and then
double click it or click ‘Add to Profile’.
4. If a password (a.k.a. ‘Network Key’) is required to access the wireless access
point, please input it in ‘Network key’ (and input it again in ‘Confirm network
key’ for confirmation). Click ‘OK’ when password is properly inputted.
NOTE: Network security type (‘Network Authentication’ and ‘Data encryption’)
will be selected automatically based on wireless access point’s security setting.
It’s not required to change these settings by yourself.
All options in this page will be filled automatically according to the access point
you wish to add to profile. However, you can still modify any of them to meet your
requirement.

10 11
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
5. Network card will attempt to connect to access point now, this may
require few seconds to minutes, please be patient. When the ‘Status’ become
‘Associated’ , your computer is connected to access point you selected. Click
‘Close’ to close conguration menu.
Please click ‘OK’ when ready.
Profile name You can give a name to this profile, so you can remember its purpose
easily. It can be any phrase to help you remember.
Network Name
(SSID)
The SSID (Service Set IDentifier, i.e. access point’s name). This field
will be filled as the access point you selected when SSID is not hidden
and grayed out. If SSID is hidden, you have to input correct SSID you
yourself.
This is a
computer-to-
computer
(ad hoc) network
Check this box if you wish to connect to another computer / network
device by ad hoc method. When not accessing to wireless access
point, you have to check this box.
Channel Select wireless channel for ad hoc connection. This option only
appears when you’re using ad hoc connection.
Network
Authentication
Select the network authentication type from drop-down menu. This
setting must be identical with the setting of wireless access point you
with to connect.
Data encryption Select the data encryption type from drop-down menu. This setting
must be identical with the setting of wireless access point you with to
connect.
ASCII /
PASSPHRASE
When the encryption type is ‘WEP’, it’s required to input a set of
‘passphrase’ to connect to wireless access point. Check ‘ASCII’ or
‘PASSPHRASE’ depends on the security setting of access point, and
input it in the box; if you select ‘PASSPHRASE’ you also need to select
the length of the key.
The passphrase must be identical with the setting of wireless access
point you with to connect.
Key index Select WEP key index. For most of access points you can select ‘1’,
but please refer to the setting of the access point.
Network key /
Confirm network
key
When the encryption type is ‘WPA’ or ‘WPA2-PSK’, it’s required to
input a set of ‘passphrase’ to connect to wireless access point. Please
input the same passphrase in two boxes for confirmation.
EAP TYPE
/ Tunnel /
Provision Mode
When authentication type is any of 802.1X, you have to select EAP
type, tunnel, and provision mode from dropdown menu. This setting
must be identical with your 802.1x authentication server.
Username /
Identity / Domain /
Password
Please input 802.1x related authentication information here.
Certicate If certication is required to authenticate with 802.1x authentication
server, please select a local certicate from dropdown list.
PAC Check this box and PAC (Privilege Access Certificate) will be
automatically selected.
NOTE: If you connected to an access point but the connection has been
dropped soon, please check security settings and re-check password spelling.
2.2.2 Using Windows Zero Configuration
Windows XP and Vista has a built-in wireless network conguration utility,
called as ‘Windows Zero Configuration’ (WZC). You can also use WZC to
congure your wireless network parameter:
1. Right-click Client conguration utility icon, and click ‘Open Config Utility’.

12 13
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
2. Check ‘Windows Zero Config’ box.
3. A message indicating that you’ve been switched to Windows Zero.
NOTE: To return to use Client utility, uncheck ‘Windows Zero Config’ box.
4. Click ‘Start’ button (should be located at the bottom-left corner of windows
desktop), click ‘Control Panel’, then click ‘Network and Internet Connections’
in Control Panel.
5. Double click ‘Network Connections’.

14 15
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
6. Right-click ‘Wireless Network Connection’ (it may have a number as sufx
if you have more than one wireless network card, please make sure you right-
click the Wireless LAN 802.11ac USB Network Adapter), then select ‘View
Available Wireless Networks’.
7. All wireless access points in proximity will be displayed here. If the access
point you want to use is not displayed here, please try to move your computer
closer to the access point, or you can click ‘Refresh network list’ to rescan
access points. Click the access point you want to use if it’s shown, then click
‘Connect’.
8. If the access point is protected by encryption, you have to input its security
key or passphrase here. It must match the encryption setting on the access
point. If the access point you selected does not use encryption, you’ll not be
prompted for security key or passphrase.
9. If you can see ‘Connected’ message, the connection between your computer
and wireless access point is successfully established.

16 17
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
CHAPTER 3: Client Utility
If you need to connect to different wireless access points at different time, like
of access point of your home, office, cybercafe, or public wireless service, you
can store the connection parameters (encryption, passphrase, security etc, etc.)
as a profile for every access point, so you don’t have to input these parameters
every time when you want to connect to a specific wireless access point.
To manage profiles, right-click the Client configuration utility icon located at
lower-right corner of computer desktop, then click ‘Open Config Utility’.
3.1 Connection Profile Management
Click the ‘Profile’ menu.
3.1.1 Add a new profile
By this function you can setup the connection parameters for a specific
wireless access point in advance, without contacting it first.If you want to
create a new profile, click ‘Profile’ menu, then click ‘Add’ button.
You’ll be prompted to input connection parameters for the wireless
access point you wish to connect:

18 19
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
Required parameters are:
Profile name You can give a name to this profile, so you can remember its purpose
easily. It can be any phrase to help you remember.
Network Name
(SSID)
The SSID (Service Set IDentifier, i.e. access point’s name). This must
be identical with the SSID of the access point you wish to connect.
This is a
computer-to-
computer (ad
hoc) network
Check this box if you wish to connect to another computer / network
device by ad hoc method. When not accessing to wireless access
point, you have to check this box.
Channel Select wireless channel for ad hoc connection. This option only
appears when you’re using ad hoc connection.
Network
Authentication
Select the network authentication type from drop-down menu. This
setting must be identical with the setting of wireless access point you
with to connect.
Data encryption Select the data encryption type from drop-down menu. This setting
must be identical with the setting of wireless access point you with to
connect.
ASCII /
PASSPHRASE
When the encryption type is ‘WEP’, it’s required to input a set of
‘passphrase’ to connect to wireless access point. Check ‘ASCII’ or
‘PASSPHRASE’ depends on the security setting of access point, and
input it in the box; if you select ‘PASSPHRASE’ you also need to select
the length of the key.
The passphrase must be identical with the setting of wireless access
point you with to connect.
Key index Select WEP key index. For most of access points you can select ‘1’,
but please refer to the setting of the access point.
Network key /
Confirm network
key
When the encryption type is ‘WPA’ or ‘WPA2-PSK’, it’s required to
input a set of ‘passphrase’ to connect to wireless access point. Please
input the same passphrase in two boxes for confirmation.
EAP TYPE
/ Tunnel /
Provision Mode
When authentication type is any of 802.1X, you have to select EAP
type, tunnel, and provision mode from dropdown menu. This setting
must be identical with your 802.1x authentication server.
Username /
Identity / Domain /
Password
Please input 802.1x related authentication information here.
Certicate If certication is required to authenticate with 802.1x authentication
server, please select a local certicate from dropdown list.
PAC Check this box and PAC (Privilege Access Certificate) will be
automatically selected.
When all required parameters are set, click ‘OK’ to create and save a new profile.
3.1.2 Remove an existing profile
When you no longer need an existing profile, you can remove it.
If you want to remove a profile, click ‘Profile’ menu, then select an existing
profile which you wish to remove, and then click ‘Remove’ button.
3.1.3 Edit an existing profile
If you have added a profile before, and you wish to change the content of the
profile, you can use this function. Please select a profile from the list first, then
click ‘Edit’ button. You’ll be provided with the contents of selected profile, and you
can edit them. Click ‘OK’ to save changes, or click ‘Cancel’ to discard changes.

20 21
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
3.1.4 Make a copy of existing profile
If you need to make a copy of a specific profile, you can use this function. This
function is very convenient when you need to build a new profile which parameters
are similar to any existing profile.
To do this, select an existing profile, then click ‘Duplicate’ button.
3.1.5 Set as default profile
If you wish to use a specific profile as default connection, you can select a
profile in the list, and click ‘Set Default’. Selected profile will become default
selection and Client configuration utility will attempt to connect to selected access
point.
You’ll be prompted to input a profile name, please use an identical name that
does not exist in profile list.
3.2 View Network Statistics, General Information, and Status
The configuration utility provides information about network statistics and link
status. If you want to know how your wireless network card works, you can use
these functions to get detailed information about the wireless connection you’re
using.
3.2.1 General Information
If you want to know the general information of the access point you’re
connecting to, click ‘General’ menu:
All general information like signal strength and link quality will be displayed
here. These information are very useful when you encounter some problem on
connecting to access point.
If you wish to get a new IP address from DHCP server, you can click ‘ReNew IP’
button.

22 23
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
3.2.2 Status
If you want to know the status of your wireless network card, click ‘Status’
menu:
3.2.3 View Network Statistics
To view the statistical data of wireless network card, click ‘Statistics’ menu,
and the statistics of wireless connection will be displayed:
All connection-related statistics is displayed here. You can click ‘Reset’ button,
to reset the statistics of all items back to 0.
3.3 Miscellaneous Settings
There are few functions provided by Client configuration utility, you can access
these functions from the bottom of configuration menu:
The descriptions of these function are listed as follow:
Show Tray Icon Check this box to show an icon on system tray.
Uncheck this box to hide it.
Radio Off Switch wireless radio off. Wireless network
functionalities are disabled.
Disable Adapter Disable wireless network adapter. All functionalities of
configration menu will disappear. To resume, unckeck
‘Disable Adapter’.
Windows Zero Config Use Windows Zero Configuration to manage wireless
connections. See section 2.2.2.

24 25
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
3.4 Establish secure connection with AP by WPS
Wi-Fi Protected Setup (WPS) is the latest wireless network technology which
makes wireless network setup become very simple. If you have WPS-enabled
wireless access point, and you want to establish a secure connection to it, you
don’t have to configure the wireless access point and setup data encryption by
yourself. All you have to do is to go to the WPS setup page of this wireless card,
click a button, and then press a specific button or enter a set of 8-digit code on
the wireless access point you wish to establish a secure connection - just three
simple steps!
For older wireless access points, it’s possible to perform a firmware upgrade
to become a WPS-enabled access point. Since they may not have a hardware
button to press for WPS setup, you can use an alternative WPS setup method
- input the pin code. Every WPS-compatible wireless network card support pin
code configuration method; you can just input the code to wireless access point,
and the wireless access point and wireless network card will do the rest for you.
This wireless network card is compatible with WPS. To use this function, the
wireless access point you wish to connect to must support WPS function too.
Now, please follow the following instructions to establish secure connection
between WPS-enabled wireless access point and your wireless network card.
This wireless network card supports 2 kinds of WPS: PIN code and Push-
Button.
Please follow the following instructions to setup WPS:
1. Right-click Client configuration utility icon, and click ‘Open Config Utility’.
2. Click ‘Wi-Fi Protect Setup’ menu.
3. You can use PIN code or Push-Button configuration, and WPS-compatible
wireless access point must use the same type of WPS. For instructions on setup
each type of WPS, see next 2 chapters for detailed instructions.

26 27
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
3.4.1 PIN Code
To use PIN Code, please click ‘Pin Input Config (PIN)’ button:
You’ll be prompted to select an access point you wish to connect. If you know its
SSID, click ‘Yes’, otherwise click ‘No’.
If you select ‘Yes’, a list of all WPS-compatible AP nearby will be displayed; you
can click ‘Refresh’ to rescan, then select an AP and click ‘Select’ button.
If you select ‘No’, wireless network card will prompt you to enter 8-digit PIN
code into your AP, without selecting an AP in advance.
After you select ‘Yes’ or ‘No’ in previous step, network card will attempt to
connect to WPS-compatible AP, and an 8-digit number will appear. Please input
this number to AP’s configuration menu within 2 minutes, and network card will
establish secure connection with AP automatically.
To stop this procedure before connection is established, click ‘Cancel’.
3.4.2 Push Button
To use Push-Button WPS configuration, please click ‘Push Button Config
(PBC)’ button. This is the easiest way to establish secure connection by WPS, but
if there’re more than one WPS-compatible AP using Push-Button config, please
use PIN Code instead.

28 29
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
After you click “Push Button Config(PBC)”, a message box will appear:
Please activate Push-Button function on wireless access point now, and
wireless network card will establish secure connection with access point within
one minute.
CHAPTER 4 Soft-AP Function
Excepting become a wireless client of other wireless access points, this
wireless adapter can act as a wireless service provider also! You can switch this
wireless adapter’s operating mode to ‘AP’ mode to simulate the function of a real
wireless access point by software, and all other computers and wireless devices
can connect to your computer wirelessly, even share the internet connection you
have!
Please follow the instructions in following chapters to use the AP function of
your wireless card.
4.1 Switch to AP Mode and Station Mode
The operating mode of the wireless card is ‘Station Mode’ (becoming a client of
other wireless access points) by default.
Please follow the following instructions to switch to AP mode:
1. Right-click Client configuration utility icon, and click ‘Open Config Utility’.
2. Select ‘Mode’, and then select ‘Access Point’.
It requires few seconds to switch to AP mode, please be patient.
After mode switch is complete, you’ll see general information of software AP,
which shows AP’s SSID and connected wireless clients.
Client mode icon :
Software AP icon:

30 31
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
4.1.1 Configure SSID and Channel
To configure software AP, click ‘Config’ button:
The ‘Wireless Network Properties’ is displayed.
Please note that Ad-Hoc mode is not available when network card is in AP
mode. The description of major setup items are listed below:
Network Name (SSID) Please input the SSID (the name used to identify this wireless
access point) here. Up to 32 numerical characters can be
accepted here, excepting space.
Channel Please select the wireless channel you wish to use, from 1 to
13.
To save changes, click ‘OK’; otherwise click ‘Cancel’ to leave this menu and
keep settings untouched.
4.1.2 Setup Soft-AP Security
To setup security options for Soft-AP, configure ‘Wireless Network Security’
section as follow:

32 33
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
The description of setup items about wireless security are listed below:
Network Authentication Select network authentication mode from dropdown menu.
Data Encryption Select data encryption method from dropdown menu.
ASCII / PASSPHRASE If the encryption method is WEP, check either ‘ASCII’
or ‘PASSPHRASE’ box and input it in the box as WEP
passphrase.
Key Index Select WEP key index (1-4). If you don’t know which one
you should use, select 1.
Network key / Conrm
network key
IF network authentication mode is WPA, please input WPA
passphrase in both box.
To save changes, click ‘OK’; otherwise click ‘Cancel’ to leave this menu and
keep settings untouched.
4.2 Advanced Settings
If you want to setup advanced settings of software access point, select
‘Advanced’ menu. If you don’t know the meaning and affects of these settings,
keep them untouched.
The description of all setup items are listed below:
Beacon Interval Please input wireless beacon time interval here.
DTIM Period Please input DTIM (Delivery Trafc Indication Message) here.
Preamble Mode Select wireless frame preamble mode (long or short) from
dropdown menu.
Key Index Select WEP key index (1-4). If you don’t know which one you
should use, select 1.
Apply Save changes.
If you changed any setting here and cause problem on communicating with
wireless clients, click ‘Set Defaults’ to reset all settings back to default setting.
4.3 Wireless Statistics
Select ‘Statistics’ menu and the data statistics about software access point will
be displayed.
Click ‘Reset’ to reset the value of every item back to ‘0’.

34 35
Nano USB Wireless Adapter Nano USB Wireless Adapter
User Manual User Manual
RNX-AC600NUB RNX-AC600NUB
4.4 Internet Connection Sharing (ICS)
In this page, you can assign a network card on your computer as the path for all
wireless clients to get connected to Internet.
If you have only one network card (except this software access point), you don’t
have to select network card here; if you have more than one network card, select
the one you wish to be used as Internet gateway.
Click ‘Apply’ to save changes (‘Apply’ is grayed out when no changes are
made in this page).
CHAPTER 5: Troubleshooting
If you encounter any problem when you’re using this wireless network card,
don’t panic! Before you call your dealer of purchase for help, please check this
troubleshooting table, the solution of your problem could be very simple, and you
can solve the problem by yourself !
Scenario Solution
I can’t find any wireless
access point / wireless
device in ‘Site Survey’
function.
1. Click ‘Rescan’ for few more times and see if you can find any
wireless access point or wireless device.
2. Please move closer to any known wireless access point.
3. Ad hoc’ function must be enabled for the wireless device you
wish to establish a direct wireless link.
4. Please adjust the position of network card (you may have to
move your computer if you’re using a notebook computer)
and click ‘Rescan’ button for few more times. If you can find
the wireless access point or wireless device you want to
connect by doing this, try to move closer to the place where
the wireless access point or wireless device is located.
Nothing happens when I
click ‘Open Config
Utility’
1. Please make sure the wireless network card is inserted into
your computer’s USB port.
2. Reboot the computer and try again.
3. Remove the card and insert it into another USB port.
4. Remove the driver and re-install.
5. Contact the dealer of purchase for help.
I can not establish
connection with a
certain wireless access
point
1. Click ‘Add to Profile’ for few more times.
2. If the SSID of access point you wish to connect is hidden
(nothing displayed in ‘SSID’ field in ‘Site Survey’ function),
you have to input correct SSID of the access point you wish
to connect. Please contact the owner of access point to ask for
correct SSID.
3. You have to input correct passphrase / security key to connect
an access point with encryption. Please contact the owner of
access point to ask for correct passphrase / security key.
4. The access point you wish to connect only allows network
cards with specific MAC address to establish connection.
Please go to ‘Status’ menu and write the value of ‘MAC
Address’ down, then present this value to the owner of access
point so he / she can add the MAC address of your network
card to his / her access point’s list.
The network is slow /
having problem when
transferring large files
1. Move closer to the place where access point is located.
2. There could be too much people using the same radio
channel. Ask the owner of the access point to change the
channel number.
Please try one or more solutions listed above.

RNX-AC600NUB_A
Technical Support Information
[e-mail] 1-800-575-9885
----------------------------------------------------------------------------------
Thank you for purchasing a quality Rosewill product.
Please register your product at: www.rosewill.com
for complete warranty information and support for your product.