Rosewill RNX-N250PCe User manual

Wireless N Adapter RNX-N250PCe
User Manual

Wireless N Adapter RNX-N250PCe User Manual
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device
and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations.
The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user
may be required to take adequate measures.
National Restrictions
2400.0-2483.5 MHz
Country Restriction Reason/remark
Bulgaria General authorization required for outdoor use and public service
France Outdoor use limited to 10 mW
e.i.r.p. within the band 2454-2483.5
MHz
Military Radiolocation use. Refarming of the 2.4 GHz band has
been ongoing in recent years to allow current relaxed regulation.
Full implementation planned 2012
Italy If used outside of own premises, general authorization is
2

Wireless N Adapter RNX-N250PCe User Manual
required
Luxembourg General authorization required for network and service
supply(not for spectrum)
Norway Implemented This subsection does not apply for the geographical area within a
radius of 20 km from the centre of Ny-Ålesund
Russian
Federation
Only for indoor applications
Note: Please don’t use the product outdoors in France.
3

Wireless N Adapter RNX-N250PCe User Manual
Table of Content
Table of Content.............................................................................................................4
Chapter 1 Overview.......................................................................................................5
Package Content.................................................................................................5
1.1Overview of the Product.........................................................................5
1.2Features....................................................................................................6
1.3System Requirement..............................................................................6
1.4Specification.............................................................................................6
Chapter 2 Installation Guide..........................................................................................8
2.1Hardware Installation..............................................................................8
2.2Software Installation................................................................................9
Chapter 3 Wireless Connection Guide.........................................................................13
3.1.Connecting with Microsoft Zero Configuration tool (Win XP).........13
3.2.Connecting with Window 7 ..................................................................14
3.3.Connecting with Wireless LAN Utility.................................................15
Chapter 4 Utility Configuration – Win XP’s Station Mode...................................18
4.1.General...................................................................................................18
4.2.Profile......................................................................................................19
4.2.1 Add.....................................................................................................19
4.2.2 Remove.............................................................................................21
4.2.3 Edit.....................................................................................................21
4.2.4 Duplicate...........................................................................................22
4.2.5 Set default ........................................................................................23
4.3.Available Network..................................................................................24
4.4.Status......................................................................................................25
4.5.Statistics..................................................................................................26
4.6.Wi-Fi Protect Setup...............................................................................27
4.6.1 Method 1 PIN Input Config (PIN)..................................................27
4.6.2 Method 2 Push Button....................................................................29
FAQ..............................................................................................................................31
Glossary......................................................................................................................32
4

Wireless N Adapter RNX-N250PCe User Manual
Chapter 1 Overview
Thank you for choosing Rosewill’s 802.11n 2T2R Wireless PCI-Express adapter –
RNX-N250PCE. RNX-N250PCE is a powerful 300Mbps Adapter into PCs without any
hassle. The Adapter can be used in Ad-Hoc mode to connect directly with other cards for
peer-to-peer file sharing or in Infrastructure mode to connect with a wireless access point
or router for access to the Internet in your office or home network. This chapter is to
introduce you more about this Wireless Adapter.
1.1 Package Content
Before getting started, please verify that your package includes the following items:
1. Rosewill RNX-N250PCE Wireless N Adapter x 1
2. 5 dBi Antenna x2
3. Low Profile Bracket x1
4. Quick Installation Guide x1
5. Resource CD x1, including:
zRosewill Wireless N Utility and Driver
zUser Manual
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or missing,
please contact with your distributor.
1.2 Overview of the Product
The adapter is an 802.11n client device; it is designed to provide a high-speed and
5

Wireless N Adapter RNX-N250PCe User Manual
unrivaled wireless performance for your computer or notebook. With a faster wireless
connection, you can get a better Internet experience, such as downloading, gaming, video
streaming and so on.
With the 802.11n technology, higher throughput improvements using MIMO (multiple input,
multiple output antennas), the RNX-N250PCE’s transfer rate up to 300Mbps for maximum
throughput. It can also interoperate with other wireless (802.11b, 802.11g) products. The
adapter supports 64/128-bit WEP, WPA and WPA2 encryption to prevent outside intrusion
and protect your personal information from being exposed.
The adapter is easy to install and manage. The Quick Setup Wizard guides you
step-by-step through the installation process; the Rosewill Wireless N Client Utility helps
you create a wireless connection immediately.
With unmatched wireless performance, reception, and security protection, the
RNX-N250PCE is the best choice for easily adding or upgrading wireless connectivity to
your notebook and computer.
1.3 Features
zComply with IEEE 802.11b, 802.11g and 802.11n standard for 2.4GHz Wireless LAN
zSupport advanced 2 x 2 MIMO Technology with up to 300Mbps data transfer rate
zSupport 64/128-bit WEP,WPA and WPA2 wireless security modes
zWindows 7-32/64 bit, Vista 32/64 bit, XP, 2000, Linux support
zSupports Sony PSP X-link for online gaming
zSupports roaming between access points when configured in Infrastructure mode
zEasily connect and secure your wireless network with WPS (Wi-Fi Protected Setup)
1.4 System Requirement
You must have at least the following
zA desktop PC with an available working PCI-Express slot
zAt least a 300MHz processor and 32MB of memory
zWindows OS for Win98SE, ME, 2000, XP, Vista, Win7
zA CD-ROM Drive
zA 802.11n 、802.11g or 802.11b Wireless Access Point/Router (for infrastructure
Mode) or another 802.11n、802.11g or 802.11b wireless adapter (for Ad-Hoc;
Peer-to-Peer networking mode).
1.5 Specification
6

Wireless N Adapter RNX-N250PCe User Manual
Chipset Realtek RTL8192CE
Standard IEEE 802.11n, IEEE 802.11g, IEEE 802.11b
Interface PCI-E Interface
Frequency Range 2.412 - 2.4835GHz
Wireless Transmit Power
802.11b: up to 18 ± 1 dBm
802.11g: up to 14 ± 1 dBm
802.11n: up to 13 ± 1 dBm
Modulation Technology OFDM/CCK
Security Support 64/128 bit WEP, WPA-PSK/WPA2-PSK (TKIP and AES)
Antenna 2x 5dBi detachable Directional Antenna
Operating: 0°C~40°C (32℉~104℉)
Temperature Storage: -20°C~70°C (-40℉~158℉)
Relative: 15% ~ 95%, Non-Condensing
Humidity Storage: 5% ~ 90% Non-Condensing
Dimensions 1.8" x 2.9" (45 x 74 mm, excluded Antenna)
Weight 0.08 lbs. (40g, excluded Antenna)
7

Wireless N Adapter RNX-N250PCe User Manual
Chapter 2 Installation Guide
2.1 Hardware Installation
1 Make sure the computer is turned off. Remove the expansion slot cover from the
computer.
(The Highlighted slots are the PCIe slot available for RNX-N250PCe to install)
2 Carefully slide RNX-N250PCe into the PCI-E slot. Push evenly and slowly and
ensure it is properly seated. (The PCB board is only for reference)
3 Secure the screw, then the antennas on.
4 Turn on your computer. Windows detects the new hardware and prompts for Driver
installation.
8

Wireless N Adapter RNX-N250PCe User Manual
2.2 Software Installation
The following driver installation guide uses Windows XP as the presumed operation
system.
1. The system finds the newly installed device automatically. Click Cancel to close this
window.
2. Insert the Driver and Utility CD-ROM into the CD-ROM driver.
3. The Wizard should run automatically, and below Smart Wizard should appear. If not,
click the Start button and choose Run. In the field that appears, enter D:\autorun.exe
(if ‘’D’’ is the letter of your CD-ROM drive).
4. Click Install Driver Installation on the Wireless Client Configuration Utility dialogue
9

Wireless N Adapter RNX-N250PCe User Manual
box, and then select the installing language from the next screen and click Next
button.
5. Click Next
6. Click Install to start installing
10

Wireless N Adapter RNX-N250PCe User Manual
7. Follow the InstallShield Wizard steps, and click Finish when done.
8. Now your PC or notebook will restart automatically.
zYou may encounter warning windows like below, please select
“install this driver software anyway” for Win7, or “Continue Anyway”
for Vista or XP.
11

Wireless N Adapter RNX-N250PCe User Manual
12

Wireless N Adapter RNX-N250PCe User Manual
Chapter 3 Wireless Connection Guide
This chapter describes how to configure your Adapter for wireless connectivity on
your Wireless Local Area Network (WLAN) and use the data security encryption
features.
After Installing the Adapter, the Adapter’s tray icon will appear in your system tray. It
appears at the bottom of the screen, and shows the signal strength using color and
the received signal strength indication (RSSI).
- If the icon is purple, there is no connection.
- If the icon is white, the network is dropping off.
- If the icon is green, there is good signal strength.
- If the icon is green, there is excellent signal strength.
In the following instruction for making a network connection, we use the provided
Utility to configure your wireless network settings.
Note: You could use either the software we provide or Microsoft Zero Configuration
tool to configure this adapter.
3.1. Connecting with Microsoft Zero Configuration tool (Win XP)
After specifying the Microsoft Zero Configuration tool to configure your wireless
network, right click on the icon on system tray. Select “View Available Wireless
Networks” to specify your wireless network.
The tool shows the available wireless networks. Select your demanding network to
connect with. To connect to a wireless network, please click Change advanced
settings to be compatible with your wireless network settings.
13

Wireless N Adapter RNX-N250PCe User Manual
3.2. Connecting with Window 7
You can easily access to wireless with Win7. First, move your mouse to lower right
hand corner as below and click on the icon where arrow pointing to.
Click Refresh to get an update of your Wireless Network Connection. This should help
you search the SSID of the network you want to connect to.
Select your desired SSID, then Click “Connect”.
14

Wireless N Adapter RNX-N250PCe User Manual
You will be prompt to ask you entering the network security key. Once entered, please
click OK to complete.
You should see below in a very short period and find out whether you are connected
or now.
3.3. Connecting with Wireless LAN Utility
We provide this Utility for users to connect to a wireless network easily. It provides
more information and configuration for this adapter. As default, the Utility is started
15

Wireless N Adapter RNX-N250PCe User Manual
automatically upon starting your computer and connects to a connectable wireless
network with best signal strength and with no security setting.
3.3.1 Step 1: Search Available Network
First Select the Available Network option:
You will see a list of the SSID that your wireless adapter has scanned in your
surrounding area. You can also “Refresh” to see the most updated list.
3.3.2 Step 2: Select and Add to Profile
Select your desired SSID (the one you want to link with), then click Add to Profile.
16

Wireless N Adapter RNX-N250PCe User Manual
After click “Add to Profile”, you will see the next window “Wireless Network Properties”
popup with your current wireless signal’s setting. (RNX-N180PCe will detect the
current setting of your SSID). So after the “Wireless Network Properties” popup, all
you need to do is to enter the password of your SSID and click OK to continute.
When done, your wireless adapter will automatically connect to this SSID. However,
Please do make sure returning to “Profile” and set your SSID Profile as your default.
So your utility will remember for the future to link to this SSID when computer is
Power-On.
Now you have complete the setup of the your wireless network. You should be ready
to surf!
17

Wireless N Adapter RNX-N250PCe User Manual
Chapter 4 Utility Configuration – Win XP’s
Station Mode
The Wireless Adapter provides two modes: Station mode and Access Point mode,
the default is Station mode under Window XP.
You can select connect wirelessly to your Wireless router/AP to connect to Internet in
station mode. But in the Access Point mode, the wireless adapter act as a wireless
access point which can share Internet connection with others. (Access Point Mode
requires Wired Connection)
4.1. General
The General tab displays current basic wireless connection information.
General Information
zStatus: Wireless networkAssociated, Ad-hoc Mode or Not Associated.
zSpeed: The data Tx rate and Rx rate of the current connection.
zType: The type of the current wireless connection , Infrastructures or ad hoc
zEncryption: Current encryption.
zSSID: The unique name of the wireless network to which the wireless adapter is
connecting.
zSignal Strength: The signal quality of the current connection.
18

Wireless N Adapter RNX-N250PCe User Manual
zLink Quality: The link quality of the current wireless connection.
Network Address
zMAC Address: The MACAddress of the Adapter.
zIPAddress: The IPAddress of the Adapter.
zSubnet Mask: The Subnet Mask of theAdapter.
zDefault Gateway: The Default Gateway address of the Adapter.
Others
zShow Tray Icon: Show USB Wireless LAN Utility icon in the windows taskbar
notification area.
zDisable Adapter: Disable the wireless adapter.
zRadio off: Turn off the radio of the wireless adapter.
4.2. Profile
Using the Profile tab, you can add, remove, edit, duplicate, and set default a
profile.
4.2.1 Add
zCreate a new Infrastructure mode profile
If you want your wireless computers to communicate with other computers on your
wired network via a wireless access point. Click the Add button to create a new
infrastructure profile.
19

Wireless N Adapter RNX-N250PCe User Manual
When the Network Info dialog box appears, enter a name for the new profile. Enter the
Network SSID. Choose the Network Authentication Mode and Data encryption from
the drop-down menu and import the network key. Then click OK button.
zCreate a new ad-hoc mode profile
If you want your wireless computers communicate with each other directly, click the
Add button to create a new ad-hoc profile. Then, check on below option:
then select the correct operating channel for your network from the Channel
drop-down menu.
Choose the Network Authentication Mode and Data encryption from the drop-down
20