Ross openGear DRA-8804 User manual

DRA-8804
Dual 3G/HD/SD Reclocking Distribution Amplifier
User Manual

Thank You for Choosing Ross
You've made a great choice. We expect you will be very happy with your purchase of Ross Technology.
Our mission is to:
1. Provide a Superior Customer Experience
• offer the best product quality and support
2. Make Cool Practical Technology
• develop great products that customers love
Ross has become well known for the Ross Video Code of Ethics. It guides our interactions and
empowers our employees. I hope you enjoy reading it below.
If anything at all with your Ross experience does not live up to your expectations be sure to reach out to
us at [email protected].
David Ross
CEO, Ross Video
[email protected]
Ross Video Code of Ethics
Any company is the sum total of the people that make things happen. At Ross, our employees are a
special group. Our employees truly care about doing a great job and delivering a high quality customer
experience every day. This code of ethics hangs on the wall of all Ross Video locations to guide our
behavior:
1. We will always act in our customers’ best interest.
2. We will do our best to understand our customers’ requirements.
3. We will not ship crap.
4. We will be great to work with.
5. We will do something extra for our customers, as an apology, when something big goes wrong and
it's our fault.
6. We will keep our promises.
7. We will treat the competition with respect.
8. We will cooperate with and help other friendly companies.
9. We will go above and beyond in times of crisis. If there's no one to authorize the required action in
times of company or customer crisis - do what you know in your heart is right. (You may rent
helicopters if necessary.)

DRA-8804 · User Manual
• Ross Part Number: 8804DR-004-04
• Release Date: January 18, 2018.
The information contained in this Guide is subject to change without notice or obligation.
Copyright
©2018 Ross Video Limited, Ross®, and any related marks are trademarks or registered trademarks of Ross Video
Limited. All other trademarks are the property of their respective companies. PATENTS ISSUED and PENDING.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, mechanical, photocopying, recording or otherwise, without the prior written permission of
Ross Video. While every precaution has been taken in the preparation of this document, Ross Video assumes no
responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the
information contained herein.
Patents
Patent numbers US 7,034,886; US 7,508,455; US 7,602,446; US 7,802,802 B2; US 7,834,886; US 7,914,332; US
8,307,284; US 8,407,374 B2; US 8,499,019 B2; US 8,519,949 B2; US 8,743,292 B2; GB 2,419,119 B; GB
2,447,380 B; and other patents pending.
Notice
The material in this manual is furnished for informational use only. It is subject to change without notice and should
not be construed as commitment by Ross Video Limited. Ross Video Limited assumes no responsibility or liability
for errors or inaccuracies that may appear in this manual.
Safety Notices
Refer to the “Important Regulatory and Safety Notices” document that accompanied your product.
Statement of Compliance
This product has been determined to be compliant with the applicable standards, regulations, and directives for the
countries where the product is marketed.
Compliance documentation, such as certification or Declaration of Compliance for the product is available upon
request by contacting [email protected]. Please include the product; model number identifiers and serial
number and country that compliance information is needed in request.
EMC Notices
US FCC Part 15
This equipment has been tested and found to comply with the limits for a class A Digital device, pursuant to part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a Commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Canada
This Class “A” digital apparatus complies with Canadian ICES-003 and part 15 of the FCC Rules.
Cet appareil numerique de la classe “A” est conforme a la norme NMB-003 du Canada.
European Union
This equipment is in compliance with the essential requirements and other relevant provisions established under
regulation (EC) No 765/2008 and Decision No 768/2008/EC referred to as the “New Legislative Framework”.
Australia/New Zealand
This equipment is in compliance with the provisions established under the Radiocommunications Act 1992 and
Radiocommunications Labeling (Electromagnetic Compatibility) Notice 2008.
Korea
This equipment is in compliance with the provisions established under the Radio Waves Act.
Class A equipment (Broadcasting and communications service for business use)
This device is a business-use (Class A) EMC-compliant device. The seller and user are advised to be aware of this
fact. This device is intended for use in areas outside home.
International
This equipment has been tested under the requirements of CISPR 22:2008 or CISPR 32:2015 and found to comply
with the limits for a Class A Digital device.
Maintenance/User Serviceable Parts
Routine maintenance to this openGear product is not required. This product contains no user serviceable parts. If
the module does not appear to be working properly, please contact Technical Support using the numbers listed
under the “Contact Us” section of this manual. All openGear products are covered by a generous 5-year warranty
Notice — Changes or modifications to this equipment not expressly approved by Ross Video Ltd. could
void the user’s authority to operate this equipment.
Warning — This equipment is compliant with Class A of CISPR 32. In a residential environment this
equipment may cause radio interference.
Notice — This is a Class A product. In domestic environments, this product may cause radio
interference, in which case the user may have to take adequate measures.
Type of Equipment User’s Guide
A
(߶הࡈ ؏ܞݦ࢕ࢢ)
Class A Equipment
(Industrial Broadcasting &
Communication Equipment)
ࢇ Е ߶הࡈ(A)ࢷ࢕ળࢶଢԻ۰ શ
֐࢕ ӖЕ یࡈ࢕Е ࢇ ࢺࡶ ࣯ࢂଜݤ ؂Ԃ
ֲ,ɼࢽ࠹ࢂ ࠇ߾۰ یࡈଜЕ ʨࡶ ּࢶࡳԻ
ଢТЬ.
This equipment is Industrial (Class A)
electromagnetic wave suitability equipment and
seller or user should take notice of it, and this
equipment is to be used in the places except for home.

and will be repaired without charge for materials or labor within this period. See the “Warranty and Repair
Policy” section in this manual for details.
Environmental Information
The equipment may contain hazardous substances that could impact health and the environment.
To avoid the potential release of those substances into the environment and to diminish the need for the extraction
of natural resources, Ross Video encourages you to use the appropriate take-back systems. These systems will reuse
or recycle most of the materials from your end-of-life equipment in an environmentally friendly and health
conscious manner.
The crossed-out wheeled bin symbol invites you to use these systems.
If you need more information on the collection, reuse, and recycling systems, please contact your local or regional
waste administration. You can also contact Ross Video for more information on the environmental performances of
our products.
Company Address
Ross Video Limited Ross Video Incorporated
8 John Street P.O. Box 880
Iroquois, Ontario, K0E 1K0 Ogdensburg, New York
Canada USA 13669-0880
General Business Office: (+1) 613 • 652 • 4886
Fax: (+1) 613 • 652 • 4425
Technical Support: (+1) 613 • 652 • 4886
After Hours Emergency: (+1) 613 • 349 • 0006
E-mail (Technical Support): [e-mail]
E-mail (General Information): solu[email protected]
Website: http://www.rossvideo.com

DRA-8804 User Manual (Iss. 04) Contents • i
Contents
Introduction 1
Overview.............................................................................................................................. 1-2
Features.................................................................................................................. 1-2
Functional Block Diagrams ................................................................................................. 1-3
Dual 1x8 Configuration......................................................................................... 1-3
Dual 1x4 Configuration......................................................................................... 1-3
User Interfaces ..................................................................................................................... 1-4
DashBoard Control System ................................................................................... 1-4
Card-edge Monitoring ........................................................................................... 1-4
SNMP Monitoring and Control............................................................................. 1-4
Documentation Terms and Conventions.............................................................................. 1-5
Installation 2
Before You Begin ................................................................................................................ 2-2
Static Discharge..................................................................................................... 2-2
Unpacking.............................................................................................................. 2-2
Installing the DRA-8804...................................................................................................... 2-3
Supported Rear Modules ...................................................................................... 2-3
Installing a Card .................................................................................................... 2-3
Cabling................................................................................................................................. 2-5
Software Upgrades............................................................................................................... 2-6
Configuration 3
Card Overview..................................................................................................................... 3-2
Monitoring Features............................................................................................................. 3-3
Status LEDs........................................................................................................... 3-3
Using DashBoard................................................................................................................. 3-4
Configuring the DRA-8804 ................................................................................................. 3-5
Enabling a Single Channel Configuration............................................................. 3-5
Enabling the Fail-over Feature .............................................................................. 3-5
Configuring the Equalizer for a Channel............................................................... 3-6
Configuring the Reclocker for a Channel.............................................................. 3-6
Loss of Input.......................................................................................................... 3-7
DashBoard Menus 4
Status Tabs........................................................................................................................... 4-2
Signal Tab.............................................................................................................. 4-2
Hardware Tab ........................................................................................................ 4-3
Product Tab ........................................................................................................... 4-4
Setup Tab ............................................................................................................................. 4-5
Alarms Tab .......................................................................................................................... 4-6
Specifications 5
Technical Specifications ...................................................................................................... 5-2

ii • Contents DRA-8804 User Manual (Iss. 04)
Service Information 6
Troubleshooting Checklist ................................................................................................... 6-2
Bootload Button..................................................................................................... 6-2
Warranty and Repair Policy ................................................................................................. 6-3

DRA-8804 User Manual (Iss. 04) Introduction • 1–1
Introduction
In This Chapter
This chapter contains the following sections:
• Overview
• Functional Block Diagrams
• User Interfaces
• Documentation Terms and Conventions
A Word of Thanks
Congratulations on choosing an openGear DRA-8804 Dual 3G/HD/SD Reclocking Amplifier.
Thank you for joining the group of worldwide satisfied Ross Video customers!
Should you have a question pertaining to the installation or operation of your DRA-8804, please
contact us at the numbers listed on the back cover of this manual. Our technical support staff is
always available for consultation, training, or service.

1–2 • Introduction DRA-8804 User Manual (Iss. 04)
Overview
Your DRA-8804 is a 3G/HD/SD Multi-Definition SDI distribution amplifier, capable of
equalizing and reclocking all common serial digital signals. An LED indicator for each channel,
at the front of the card, identify the presence of incoming video, simplifying system
troubleshooting.
A special feature of the DRA-8804 is the ability to operate in a number of different channel
configurations. Dual channel mode is ideal for applications requiring only a few outputs, such as
mid-cable signal boosters, router expansion, or signal cleanup. Up to 20 SDI distribution channels
can be housed in a 2RU space using the DRA-8804.
Features
The DRA-8804 includes the following features:
• Equalizes and reclocks SDI signals of 270Mbps, 1.485Gbps, and 2.97Gbps
• Supports DVB-ASI (EN 50083-9), and SMPTE 310 signals
• Flexible channel configurations where the card can operate as a:
› Dual 1x8 or Single 1x16 (requires the 8320AR-302 Full Rear Module)
› Dual 1x4 or Single 1x8 (requires the 8320AR-300 Full Rear Module)
• Configure and monitor via DashBoard
• Automatic detection of incoming data rate
• Automatically mutes the channel output when a loss of input occurs
• Automatically performs a fail-over switch between the two SDI inputs (configurable via
DashBoard)
• LED indicators for input signal presence
• Excellent input and output return loss
• Fits DFR-8321 series and OG3-FR series frames
• Fully compliant with openGear specifications
• 5 year transferable warranty

DRA-8804 User Manual (Iss. 04) Introduction • 1–3
Functional Block Diagrams
The DRA-8804 configuration depends on the rear module you are using.
Dual 1x8 Configuration
Figure 1.1 describes the workflow of the DRA-8804 with the 8320AR-302 Full Rear module.
This configuration has the DRA-8804 operating as a dual reclocking 1x8 with HD-BNC
connections.
Figure 1.1 Simplified Diagram — Dual 1x8 Configuration (8320AR-302)
Dual 1x4 Configuration
Figure 1.2 describes the workflow of the DRA-8804 with the 8320AR-300 Full Rear module.
This configuration has the DRA-8804 operating as a dual reclocking 1x4 with BNC connections.
Figure 1.2 Simplified Diagram — Dual 1x4 Configuration (8320AR-300)
IN CH B
IN CH A
Equalizer
Equalizer
OUT 1A
OUT 2A
OUT 3A
OUT 4A
OUT 5A
OUT 6A
OUT 7A
OUT 8A
OUT 1B
OUT 2B
OUT 3B
OUT 4B
OUT 5B
OUT 6B
OUT 7B
OUT 8B
Reclocker
Reclocker
Reclocker
IN CH B
OUT 1B
OUT 2B
OUT 3B
OUT 4B
IN CH A
OUT 1A
OUT 2A
OUT 3A
OUT 4A
Equalizer
Equalizer Reclocker

1–4 • Introduction DRA-8804 User Manual (Iss. 04)
User Interfaces
The following interfaces are available for control and monitoring of your DRA-8804.
DashBoard Control System
DashBoard enables you to monitor and control openGear frames and cards from a computer.
DashBoard communicates with other cards in the openGear frame through the Network
Controller Card.
For More Information on...
• menus in DashBoard, refer to the chapter “DashBoard Menus” on page 4-1.
• installing and using DashBoard, refer to the DashBoard User Manual.
Card-edge Monitoring
The card-edges provide LEDs for monitoring the status of the input signal.
For More Information on...
• card-edge LEDs, refer to the section “Monitoring Features” on page 3-3.
SNMP Monitoring and Control
The Network Controller card in the openGear frame provides optional support for remote
monitoring and control of your frame and openGear cards using Simple Network Management
Protocol (SNMP), which is compatible with many third-party monitoring and control tools.
For More Information on...
• SNMP controls on your card, refer to your DRA-8804 Management Information Base
(MIB) file.
• SNMP Monitoring and Control, refer to your MFC-8300 Series or MFC-OG3 Series
User Manual.

DRA-8804 User Manual (Iss. 04) Introduction • 1–5
Documentation Terms and Conventions
The following terms and conventions are used throughout this manual.
Terms
The following terms are used:
•“Board” and “Card” both refer to the card, including all components and switches.
•“DashBoard” refers to the DashBoard Control System.
•“DFR-8321 series” refers to the DFR-8321 series frames and all available options unless
otherwise indicated.
•“Network Controller Card” refers to the MFC-8320-N, MFC-8322-N, and
MFC-OG3-N Series Network Controller Cards unless otherwise indicated.
•“OG3-FR series” refers to the OG3-FR series frames and all available options unless
otherwise indicated.
•“openGear frame” refers to all versions of the DFR-8321 series and OG3-FR series
frames unless otherwise indicated.
•“Operator” and “User” both refer to the person who uses the DRA-8804.
•“System” and “Video system” both refer to the mix of interconnected production and
terminal equipment in which the card operates.
Conventions
The following conventions are used:
•The “Operating Tips” and “Note” boxes are used to provide additional user information.

1–6 • Introduction DRA-8804 User Manual (Iss. 04)

DRA-8804 User Manual (Iss. 04) Installation • 2–1
Installation
In This Chapter
This chapter provides instructions for installing the rear module for your DRA-8804, installing
the card in the openGear frame, cabling details, and how to upgrade the software on your card(s).
The following topics are discussed:
• Before You Begin
• Installing the DRA-8804
•Cabling
• Software Upgrades

2–2 • Installation DRA-8804 User Manual (Iss. 04)
Before You Begin
Before proceeding with the instructions in this chapter, ensure that your openGear frame is
properly installed according to the instructions in the manual that accompanied it.
Static Discharge
Throughout this chapter, please heed the following cautionary note:
Unpacking
Unpack each card you received from the shipping container and ensure that all items are included.
If any items are missing or damaged, contact your sales representative or Ross Video directly.
ESD Susceptibility — Static discharge can cause serious damage to sensitive
semiconductor devices. Avoid handling circuit boards in high static environments such as
carpeted areas and when synthetic fiber clothing is worn. Always exercise proper grounding
precautions when working on circuit boards and related equipment.

DRA-8804 User Manual (Iss. 04) Installation • 2–3
Installing the DRA-8804
The DRA-8804 can be installed in the DFR-8321 series frames and the OG3-FR series frames
using one of the supported rear modules.The procedure for installing the rear module and card in
your openGear frame is the same regardless of the rear module used.
Supported Rear Modules
The rear module depends on the configuration you wish to use.
•Dual 1x8 configuration — The 8320AR-302 Full Rear Module is required.
•Dual 1x4 configuration — The 8320AR-300 Full Rear Module is required.
Installing a Card
You must first install the rear module in the frame and then install the card in the appropriate slot
within an openGear frame. This section outlines how to perform both tasks.
To install the rear module in the openGear frame
1. Refer to the manual for your frame to ensure that the openGear frame is properly
installed.
2. On the rear of the frame, locate the card frame slot.
3. Remove the Blank Plate from the rear of the slot you have chosen for card installation.
4. As shown in Figure 2.1, seat the bottom of the rear module in the seating slot at the base
of the frame’s back plane.
Figure 2.1 Rear Module Installation in an OG3-FR Series Frame (Cards not shown)
5. Align the top hole of the rear module with the screw hole on the top edge of the frame
back plane.
Notice — Ensure that you install the DRA-8804 using one of the supported rear modules
listed below. Installing the DRA-8804 with an unsupported rear module can damage the card,
the rear module, or both.
Screw Hole
Module Seating Slots

2–4 • Installation DRA-8804 User Manual (Iss. 04)
6. Using a Phillips screwdriver and the supplied screw, fasten the rear module to the back
plane. Do not over-tighten.
7. Verify whether your Rear Module Label is self-adhesive by checking the back of the
label for a thin wax sheet. You must remove the wax sheet before affixing the label.
8. Affix the supplied Rear Module Label to the BNC area of the Rear Module.
9. Ensure proper frame cooling and ventilation by having all rear frame slots covered with
rear modules or blank metal plates.
To install the card in the openGear frame
1. Locate the Rear Module you installed in the procedure “To install the rear module in
the openGear frame” on page 2-3.
2. Hold the card by the edges.
3. Carefully align the card edges with the slots in the frame.
4. Fully insert the card into the frame until the rear connection plugs are properly seated on
the mid-plane and rear modules.

DRA-8804 User Manual (Iss. 04) Installation • 2–5
Cabling
The DRA-8804 can operate as a dual 1x8, or a dual 1x4 depending on the rear module you are
using. This section provides cabling details based on the configuration.
Dual 1x8 Configuration
The 8320AR-302 Full Rear Module is required when operating in a dual 1x8 configuration. Each
rear module occupies two slots and accommodates one card. This rear module provides one SDI
input and eight SDI outputs per channel on HD-BNC jacks. (Figure 2.2)
Figure 2.2 Cable Connections for the 8320AR-302 Full Rear Module
Dual 1x4 Configuration
The 8320AR-300 Full Rear Module is required when operating in a dual 1x4 configuration. Each
rear module occupies two slots and accommodates one card. This rear module provides one SDI
input and four SDI outputs per channel on BNC jacks. (Figure 2.3)
Figure 2.3 Cable Connections for the 8320AR-300 Full Rear Module
IN CH A
OUT 2A
OUT 1A*
OUT 3A*
OUT 4A
OUT 5A*
OUT 6A*
OUT 7A
IN CH B
OUT 1B*
OUT 2B
OUT 3B*
OUT 4B
OUT 5B*
OUT 6B*
OUT 7B
OUT 8BOUT 8A
2
4
6
8
10
12
14
16
18
1
3
5
7
9
11
13
15
17
Inverted outputs are noted with an asterisk (*).
12
34
56
78
910
IN CH A
OUT 1A
OUT 2A
OUT 3A
OUT 4A
IN CH B
OUT 1B
OUT 2B
OUT 3B
OUT 4B

2–6 • Installation DRA-8804 User Manual (Iss. 04)
Software Upgrades
The DRA-8804 can be upgraded in the field via the Network Controller Card in your openGear
frame. Note that DashBoard version 6.2.0 or higher is required.
To upgrade the software on a card
1. Contact Ross Technical Support for the latest software version file.
2. Display the Device View of the card by double-clicking its status indicator in the Basic
Tree View.
3. From the Device View, click Upload to display the Select file for upload dialog.
4. Navigate to the *.bin upload file you wish to upload.
5. Click Open.
6. If you are upgrading a single card, click Finish to display the Uploading to Selected
Devices dialog. Proceed to step 8.
7. If you are upgrading multiple cards:
•Click Next > to display the Select Destination menu. This menu provides a list of
the compatible cards based on the card selected in step 2.
• Specify the card(s) to upload the file to by selecting the check box(es) for the cards
you wish to upload the file to.
• Verify that the card(s) you wish to upload the file to. The Error/Warning fields
indicate any errors, such as incompatible software or card type mismatch.
•Click Finish to display the Uploading to Selected Devices dialog.
8. Monitor the upgrade.
• The Uploading to Selected Devices dialog enables you to monitor the upgrade
process.
•Click OK to complete the upgrade.
• The card(s) are temporarily taken offline during the re-boot process. The process is
complete once the status indicators for the Card State and Connection fields return
to their previous status.