Rowlinson Garden Products SS352C User manual

Before assembly
•We recommend that time is taken to
read the instructions before starting
assembly, then follow the easy step
by step guide.The instruction sheet
is only a guide to the assembly.
Certain items may not be shown to scale.
•Check all components prior to assembly
•This product should be assembled
by no less than two people.
•Never attempt to erect the assembly
in high winds.
•Drill all components where indicated.
Recommended tools for assembly
•Cross head screw driver
•Drill with 3mm diameter drill bit
•Hammer
x 2 Drill
No. Components Qty.
1Side base frame 2
2Back base frame 1
3Left wall panel (Width 785mm) 1
4Right wall panel (Width 785mm) 1
5Left back panel (Width 705mm) 1
6Right back panel (Width 705mm) 1
7Support rail 1
8To p f r a m e 1
9Planting trough 1
10 Trough liner 1
11 Front rail 1
12 Left door (Width 705mm) 1
13 Right door (Width 705mm) 1
No. Fixing kit Qty.
14 Metal L-brackets 2
15 100mm screws 5
16 80mm screws 9
17 50mm screws 29
18 32mm screws 8
19 10mm nails 40
20 Hinge 4
21 Turn button 2
22 50mm screws 5
23 25mm screws 34 1
2
3
4
5
6
7
8
9
10
11
Kanny Bin Canopy
Assembly Instructions
English SS352C
If in doubt of any aspect regarding the assembly, use or safety of your product please contact us :
Help Line (Normal Office Hours) 01829 261 121
ROWLINSON GARDEN PRODUCTS LIMITED
Green Lane
Wardle Nr. Nantwich
Cheshire
CW5 6BN
We constantly improve the quality of our products, occasionally the
components may differ from the components shown and are only
correct at time of printing. We reserve the right to change the
specification of our products without prior notice.
2015 © Rowlinson Garden Products Ltd
25mm
12
13
6. Doors
Attach each door using two hinges and 8 x 25mm per hinge as shown. Position the top hinge approximately 180mm
from the top of the door. Position the bottom hinge approximately 180mm from the bottom of the door.
25mm
Caution
it is recommended the
Kanny Bin Store is
bolted to a solid surface.
50mm
7. Front rail and turn buttons
Position the front rail flush to the bottom edge of the top frame. Secure in place using 5 x 50mm screws. Screw through
the frame into the ends of each angled rafter. Attach a turn button above each door and secure each one to the front
rail using 1 x 25mm screws for each turn button.
Drill
It is recommended to drill pilot
holes for the front rail screws with
a 3mm drill bit before assembly.
Please Note:
Diagrams in this section show assembly with
planting trough removed for visual purposes
only. It is not necessary to remove the
trough to fit these parts.

Drill
3. Support rail
Position the support rail between the two side panels. Align so that it is flush with the front and top of the sides.
Secure at each end using 2 x 80mm screws. Screw through the side panels into the ends of the rail. Position the Metal
L-brackets under each corner between the rail and the side panels and secure each bracket with 32mm screws.
It is recommended
to drill pilot holes for
these screws with a
3mm drill bit before
assembly.
50mm
50mm
50mm
2. Base frame
Lay the unit on its back. Position the three base rails as shown. Secure the back panel base rail with 3 x 50mm screws
and each side base frame with 2 x 50 mm screws. When all the base frames are attached stand the unit up.
80mm
80mm
32mm
4. Top frame and front rail
The top frame can be positioned so it can slope either way. Place the top frame onto the assembly with the slope
running the desired way. Secure through the thicker end of each angled rafter with 1 x 100mm screw. Screw through
the rafter into the frame of the back panels. Secure through the thinner end of each angled rafter with
1 x 80mm screw. Screw through the rafter into the support rail.
100mm
80mm
1. Wall panels
Secure the two back panels together as shown using 4 x 50mm screws. Attach each side panel using 4 x 50mm
screws. Screw through the frame of the back panels into the frames of the sides.
Drill
It is recommended to drill pilot
holes for these screws with a
3mm drill bit before assembly.
Drill
It is recommended to drill pilot
holes for 80mm screws with a
3mm drill bit before assembly.
Drill
It is recommended to drill pilot
holes for these screws with a
3mm drill bit before assembly. Note:
The top frame can be positioned so
the slope can run either way
depending on preference.
50mm
5. Plant trough and liner
Position the planting trough on top of the assembly. Secure in place using 10 x 50mm screws. Screw through the
trough into the angled rafters. Lay the liner in the trough, fold in the corners and pin in place using 40 x 10mm nails
around the top edge of the liner.
10mm