Ruby Tech ES-2310Q User manual

ES-2310Q:
10-Port L2 Managed Fast Ethernet Switch with 2 100Base-FX Ports
Key FeaturesKey Features
Standard compliance
---IEEE 802.3 10Base-T
---IEEE 802.3u 100Base-TX
---IEEE 802.3x Flow Control Capability
---ANSI/IEEE 802.3 Auto-negotiation
---IEEE 802.1q VLAN
RoHS Compliance
Subscriber Interface
---1-8 10/100Mbps Fast Ethernet ports.
---9,10 are Fast Ethernet Fiber ports with
SEP module
---Auto-Negotiation and Auto-MDIX
---Back pressure flow control for half
duplex.
---IEEE 802.3x flow control for full duplex
---Connector: 8 ports RJ-45 and 2 ports
Fiber (SEP)
Performance
Switching capacity:
---Non-blocking switch fabric supports up
to 8 FE+2 SEP ports
---8 K MAC addresses
---256K packet buffer and 128K control
memory
VSM(Virtual Stacking Management)
---Supports 16 devices stacking
---Multiple switches can be managed via
one IP address, just like software
stacking
---Low cost and easily to establish
network environment, not extra
hardware require
---Not center on the physical location of
wiring closets
---In tag-base VLAN, supports egress/
ingress packet filter
---Q-in-Q is an efficient method for
enabling Subscriber Aggregation
QoS
---Port Based (VIP Port), 802.1p , TOS
and Diffserv(IPv4/IPv6) based QoS
packet classification
---Supports four level priority queues to
prioritize in-bound and out-bound traffic
ES-2310Q
RUB
TECHTECH
BenefitsBenefits
QoS with four priority queues
The QoS(Quality Of Service) feature provides four internal queues to
support four different classifications of traffic. High priority packet streams
experience less delay inside the switch, which supports lower latency for
certain delay-sensitive traffic. The ES-2310Q can classify the packet as one
of the four priorities according to vip port, 802.1p priority tag, DiffServ and/or
IP TOS. The QoS operate at full wire speed. The actual scheduling at each
egress port can be based upon a strict priority, weighted round robin or a mix
of both.
Port Mirroring
This mechanism helps track network errors or abnormal packet transmission
without interrupting the flow of data. Allow ingress traffic to be monitored by a
single port that is defined as mirror capture port. The mirror capture port can
be any 10/100 port, 10/100/1000 port. Mirroring multiple ports is possible but
can create congestion at the mirror capture port.
Q-in-Q VLAN for performance & security
The VLAN feature in the switch offers the benefits of both security and
performance. VLAN is used to isolate traffic between different users and thus
provides better security. Limiting the broadcast traffic to within the same
VLAN broadcast domain also enhances performance. Q-in-Q, the use of
double VLAN tags is an efficient method for enabling Subscriber Aggregation.
This is very useful in the MAN.
Isolated Group, provides protection for certain ports
The isolated group feature allows certain ports to be designated as protected.
All other ports are non-isolated. Traffic between isolated group members is
blocked.
Traffic can only be sent from isolated group to non-isolated group.
Mac-based 802.ad LACP with automatic link fail-over
Dynamic fail-over means packets will not get assigned to any trunk member
port that has failed. If one of the ports were to fail, traffic will automatically get
distributed to the remaining active ports.
802.1x Access Control improves network security
802.1x features enable user authentication for each network access attempt.
Port security features allow you to limit the number of MAC addresses per
port in order to control the number of stations for each port. Static MAC
addresses can be defined for each port to ensure only registered machines
are allowed to access. By enabling both of these features, you can establish
an access mechanism based on user and machine identities, as well as
control the number of access stations.
802.1d Compatible & 802.1w Rapid Spanning Tree
For mission critical environments with multiple switches supporting STP, you
can configure the switches with a redundant backup bridge path, so
transmission and reception of packets can be guaranteed in event of any fail-
over switch on the network.
L2 Managed Switch
Fast Ethernet Switch
Fast EthernetSwitch

RUB
TECHTECH
Broadcast/Multicast/unknown-unicast Storm Control
To limit too many broadcast/multicast/unknown-unicast flooding in the
network, broadcast/multicast storm control is used to restrict excess traffic.
Threshold values are available to control the rate limit for each port. Packets
are discarded if the count exceeds the configured upper threshold.
Technical SpecificationsTechnical Specifications
LED Description
Network Interface
Full Forwarding Packet Rate: PPS (64 Bytes packets per second)
Cable and Maximum Length
Hardware Spec
---Supports two scheduling, WRR and
Strict
---Supports priority in a Q-in-Q tag
Bandwidth Control
---Supports bandwidth rating per port
ingress and egress rate limit
1000Mbps with 1Mbps increment
Broadcast Storm
---Multicast/Broadcast/Unknown-Unicast
Storm suppression.
Transmission Mode
---10/100Mbps support full or half duplex
Transmission Speed
---10/100Mbps for TP and 100Mbps for
Fiber
Port Mirroring
---Support 1: N RX port mirroring
---Supports port sniffer function with 3
modes:
(TX Monitor Mode, RX Monitor Mode
and TX-RX pair Monitor Mode)
Isolated Group
---Provide one group allows certain ports
to be designated as protected
Restricted Group
---Can decide the direction of transmitting
packets for the specific port
Protocol
LACP
---2 Fast Ethernet +1 Gigabit Ethernet
groups
---Per-group max 4 member
---Provides DA, SA and DA+SA Mac-
based trunking with automatic link fail-
over
GVRP/GARP
---802.1q with GVRP/ GARP
Multicasting
---Supports IGMP snooping including
active and passive mode
STP/RSTP
---802.1d/1w
Network Security
---802.1x access control
---Isolated group
---Restricted group
---Management Access Policy Control
---Static mac, to limit which mac
addresses can pass through or not
---Mac addresses learning limit, to set
up the maximum amount of mac that
each port can learn
Snmpv1,v2c Network Management
RFC 1213 MIB (MIB-II)
Interface MIB
Address Translation MIB
IP MIB
ICMP MIB
TCP MIB
UDP MIB
SNMP MIB
L2 Managed Switch
Fast Ethernet Switch
Fast EthernetSwitch
LED Color Function
Global POWER Green -Lit when +5Vpower is comingup
Global CPU Green -Blinks when CPUis active
Port LINK/ACT Green -Lit when connectionwith remote device
1-8 is good
-Blinks when any traffic is present
Port 10/100 Green -Lit Green whenTP link on 1000Mbps
1-8 Mbps /Amber speed
-Off when 10Mbps or nolink occurs
Port SEP Green - Lit whenSEP connection with remote
9,10 device is good
-Blinks when any traffic is present
Category Connector Transmission Max. Cable Wavelength
Length
10-T/ RJ-45 Full/Half Duplex 100M /
100-TX
100-FX SC/ST Full/Half Duplex 2Km 1310nm
(M-M) 50/125ì
100-FX SC Full/Half Duplex 5/20/60Km 1310nm
(S-M) 9/125ì
100-FX Bidi-SC Full/Half Duplex 20Km 1310nm
(S-M) 9/125ì 1550nm
Forwarding Rate Speed
14,880PPS 10Mbps
148,800PPS 100Mbps
Dimensions 44(H) x 220(W)x 130.5(D) mm
Feature Detailed Description
Voltage 100~240 VAC
Frequency 50~60 Hz
Consumption 8.9W
Ambient Temperature 0 to 40 C
Humidity 5% to 90%
Safety Comply with FCCPart 15 ClassA& CE
Mark Approval
Feature Detailed Description
TP Cat. 5 UTP cable, up to 100m
100Base-FX SC/ST M-M Up to 2Km
100Base-FX SC S-M Single-Mode Fiber, up to
5/20/60Km
100Base-FX WDM SC S-M Single Fiber, BiDi 20Km

RUB
TECHTECH
RFC 1757 RMON MIB
Statistics Group 1
History Group 2
Alarm Group 3
Event Group 9
RFC 1493 Bridge MIB
RFC 1643 Ethernet MIB
Enterprise MIB
OverviewOverview
ES-2310Q is a Managed Fast Ethernet
switch that supports SNMP, Web UI and
CLI management interface and with 8 ports
10/100Base-TX (RJ-45 connectors) and 2
ports 100Base-FX (SEP). It is a standard
switch that meets all IEEE 802.3/u/x/z
Gigabit, Fast Ethernet specifications. In
addition, the switch implements the QoS
(Quality of Service), VLAN, Mac Filtering
Policy, Port Mirror, VLAN and full L2
protocols. It has a rich feature set suitable
for streaming VoIP, video, and data
traffics for multimedia applications.
In this switch, Port 9, 10 support 2-port
100Base-FX ports(SEP) , and the 2-port
fiber is used 2 slots for removable SEP
module supporting, they are 100Base-
FX fiber module.
Fast Ethernet Switch
Fast EthernetSwitch
L2 Managed Switch
Ordering InformationOrdering Information
ES-2310Q:
10-Port L2 Managed Fast Ethernet Switch with 2 100Base-FX Ports
Optional SEP Fiber Module
Ruby Tech Corp.
2F, No.7, Lane 50, Nan Kang Road, Sec.3, Taipei, Taiwan http://www.rubytech.com.tw
TEL:[phone] FAX:[phone] E-mail [email protected]
FM-SEP.SC SEP, FE SCMulti-Mode Fiber Module1310nm
FM-SEP.SC.S05 SEP, FE SCSingle-Mode 5km FiberModule
1310nm
FM-SEP.SC.S20 SEP, FE SCSingle-Mode 20km Fiber Module
1310nm
FM-SEP.SC.S40 SEP, FE SCSingle-Mode 40km Fiber Module
1310nm
FM-SEP.SC.S60 SEP, FE SCSingle-Mode 60km Fiber Module
1310nm
FM-SEP.BS5.S20 SEP, FE BiDiSC 20km ModuleSingle Fiber
1550nm, Type 1
FM-SEP.BS3.S20 SEP, FE BiDiSC 20km ModuleSingle Fiber
1310nm, Type 2