Rugged Computing WARRIOR Quick start guide
&
Assembly Instructions
OWNER’S MANUAL
Y100-020818
SKU# Y100
STRENGTH & FITNESS
WARRIOR
POWER RACK
Warning, Safety & Maintenance
2
Be sure that all users carefully read and understand all
warning, safety and maintenance labels on the machine
before each use. Failure to do so may result in death or
serious injury.
It is imperative that you retain this Owner’s Manual and be
sure all warning labels are legible and intact. Replacement
Owner’s Manuals and warning labels are available from
Rugged Fitness.
If you have any questions about the operation, set up or
maintenance of this machine please call our customer service
department at 1 (800) 556-3113.
Table of Contents
3
Important Safety Instructions
4
Il est conseille de subir un examen medical complet avant d’entreprendre tout programme d’exercise.
Si vous avez des etourdissements ou des faiblesses, arretez les exercices immediatement.
Antes de comenzar cualquier programma de ejercicios, deberias tener un examen sico con su doctor.
When using exercise equipment, you
should always take basic precautions,
including the following:
m
m Do not remove any safety labels from the
machine.
m
m
m
m
m
m
m
m
m
m
m
Personal Safety During Assembly
m
m
m
RUGGED FITNESS POWER
RACK.
1-800-556-3113
Obtaining Service
Toll Free: 1-800-556-3113
Phone: 1-708-427-3555
Fax: 1-708-427-3556
Hours: M-F 8:30-5:00 CST
E-Mail: service@ruggedtness.com
Or write to: Rugged Fitness
Service Department
1900 S. Des Plaines Ave.
Forest Park, IL 60130 USA
Retain this Owner’s Manual for future
reference. If you need to order replacement
parts please be prepared to provide the
following information when contacting us so
that we can assist you better.
1. Model Number
2. Place of Purchase
3. Serial Number (S/N)
4. Part # and Description
Preparation
5
-
-
Required Tools
Y100
m
m
m
Installation Requirements
Y100Y100
Fill out and mail the warranty card
Assembly Tips
Y100
NOTE:
CAUTION:
45
6
Y100 Hardware Illustration
7
Y100 Hardware Illustration
7
8
Y100 Parts & Hardware List
Part# Qty Description
Part# Qty Description
45
9
Parts Illustration
45
10
Parts Illustration
45
11
Parts Illustration
12
STEP
1
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Finger tighten all hardware in this step. DO NOT wrench tighten until instructed.
Some components may be pre-assembled. Nylon lock nuts will not fully screw onto
bolts, they must be wrench tightened to fully go on.
1A. (A & B)(H)
(C)
(#3) M16x110mm Hex Head Bolt, QTY 4
(#4) M16 Regular Flat Washer, QTY 8
(#6) M16 Nylon Lock Nut, QTY 4
NOTE 1:
Please refer to the drawing for the correct bolt hole locations. The bolt
holes are the 7th and 10th holes from the open end of the Base Frame.
1B. (D)(C)
(#2) M16x90mm Hex Head Bolt, QTY 4
(#4) M16 Regular Flat Washer, QTY 8
(#6) M16 Nylon Lock Nut, QTY 4
1C. (F)(D)
(#1) M16x80mm Hex Head Bolt, QTY 4
(#4) M16 Regular Flat Washer, QTY 4
(#5) M16 Large Flat Washer, QTY 4
(#6) M16 Nylon Lock Nut, QTY 4
NOTE 2:
It is recommedated to install the equipment with at least two persons.
STEP
1
13
Note 1:
Front of
Rack
Back of
Rack
14
STEP
2
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Finger tighten all hardware in this step. DO NOT wrench tighten until instructed.
Some components may be pre-assembled. Nylon lock nuts will not fully screw onto
bolts, they must be wrench tightened to fully go on.
2A. (C) (A & B)
(#3) M16x110mm Hex Head Bolt, QTY 4
(#4) M16 Regular Flat Washer, QTY 8
(#6) M16 Nylon Lock Nut, QTY 4
NOTE:
Please refer to the drawing for the correct bolt hole locations. The bolt
holes are the 7th and 10th holes from the front end of the Base Frame.
2B. (D)(C)
(#2) M16x90mm Hex Head Bolt, QTY 4
(#4) M16 Regular Flat Washer, QTY 8
(#6) M16 Nylon Lock Nut, QTY 4
2C. (E)(D)
(#1) M16x80mm Hex Head Bolt, QTY 4
(#4) M16 Regular Flat Washer, QTY 4
(#5) M16 Large Flat Washer, QTY 4
(#6) M16 Nylon Lock Nut, QTY 4
NOTE 2:
It is recommedated to install the equipment with at least two persons.
STEP
2
15
Note 1:
Front of
Rack
Back of
Rack
16
STEP
3
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Finger tighten all hardware rst in this step. Wrench tighten ALL hardware at the end of
STEP 3A. Some components may be pre-assembled. Nylon lock nuts will not fully screw
onto bolts, they must be wrench tightened to fully go on.
3A. (G)(D)
8 - (#3) M16x110mm Hex Head Bolt, QTY 8
8 - (#4) M16 Regular Flat Washer, QTY 8
8 - (#5) M16 Large Flat Washer, QTY 8
8 - (#6) M16 Nylon Lock Nut, QTY 8
3B. (J)
(A & B).
NOTE 1:
SECURELYanchorthemachinetotheoorusingtheanchorholes
provided. Please consult a professional contractor for the actual
anchoring of the machine.
NOTE 2:
It is recommedated to install the equipment with at least two persons.
STEP
3
17
Anchor Hole
Anchor Hole
Front of
Rack
Back of
Rack
18
STEP
4
Be careful to assemble all components
in the sequence they are presented.
NOTE:
Some components may be pre-assembled. Nylon lock nuts will not fully screw onto bolts,
they must be wrench tightened to fully go on.
Adjustable J Cups and Pipe & Pin Safeties
4A. (K & L)(D)
4B. (N)(D)
(M)(N)(D)
4C. (P) (M)
STEP
4
19
45
20
Notes
This manual suits for next models
1
Table of contents
Other Rugged Computing Sport & Outdoor manuals
