RuggON CHASER User manual

CHASER
RuggedTouchMonitor
User's Manual
Model: RTD S11
Ver.: 1.2

© 2020 RuggON Corporation. All rights reserved.
TRADEMARKS
RuggON logo is a trademark of RuggON Corporation, registered in the United States Patent
and Trademark Office and in other countries. All brand and product names are trademarks or
registered trademarks of their respective owners.
Images shown in this document may vary slightly from actual products at time of shipping.
Information in this manual is subject to change without notice.

Table of Contents
About This Manual
Related Information......................................................................................1
Conventions..................................................................................................1
Safety Information
Intended Use................................................................................................2
Maintenance and Operation Overview.........................................................2
Safe Environments of Use............................................................................3
Distractions...................................................................................................3
Safety ...........................................................................................................3
Electrical Hazards.........................................................................................3
Security Guidelines for Mounting..................................................................3
Environmental...............................................................................................3
Cleaning and Servicing.................................................................................4
Touchscreen Care ........................................................................................4
Regional Compliance ...................................................................................5
Chapter 1. Introduction
About This Guide..........................................................................................7
Unpacking the Device...................................................................................7
Parts List.......................................................................................................8
Technical Specifications ...............................................................................9
Identifying the Device..................................................................................10
Dimensions..................................................................................................14
Touch Screen...............................................................................................15
Chapter 2. Getting Started
Unpacking the Device.................................................................................16
Connecting to External Cabling..................................................................16
Connecting the Power Supply....................................................................21
Mounting Hardware....................................................................................23
i

ii
Chapter 3. Operations
LED Indicators ............................................................................................24
Enabling and Disabling Black Out Function ...............................................24
Adjusting Volume........................................................................................25
Adjusting Brightness...................................................................................26
Switching Video Sources............................................................................27
Muting Audio...............................................................................................28
Enabling and Disabling Night Mode Function.............................................28

5
About This Manual
The Rugged Touch Monitor User’s Manual provides instruction for qualified personnel to follow
when setting up a new Rugged Touch Monitor device.
This document is intended for use by qualified personnel to compliment the training and expertise,
not to replace it.
Related Information
Current information and manuals are available for download at the following website:
https://www.ruggon.com
Conventions
Bolded or Underlined text is used to emphasize the designated information.
Note: A Note is used to provide additional information for the device or settings.
Caution: A Caution is used to warn against potential hazards or to caution
Warning: A Warning is used to identify immediate hazards for property damage,
injury or death.
1

2
Safety Information
For important safety and health information as well as Limited Warranty terms applicable to the
RuggON® Rugged Touch Monitor, read the document prior to using the device. Failure to follow the
instructions, the proper setup, use, and care of this device may increase the risk of serious injury
or death, or damage the device.
„ Do not place anything on the power cables and make sure they are not located where it can
be tripped over or stepped on.
„ Use only the provided power cable for use with the device. Use of unapproved accessories
or cables may result in fire or explosion.
„ If the device is moved between environments with very different temperature and/ or humidity
ranges, condensation may form on or within the device. Avoid damaging the device by
allowing sufficient time for the moisture to evaporate before using the device. If moisture has
accumulated on the device, a clean cloth can be used to wipe the surface.
„ When disconnecting cables, pull on the connector or on its strain relief loop, not on the
cable itself. When pulling out or plugging in the connector, keep it evenly aligned to prevent
bending the connector pins.
„ Directly stowing or mounting the rugged touch monitor in a vehicle airbag deployment zone
might entail higher risks of life.
„ Never use the touch screen monitor while driving.
Intended Use
The Rugged Touch Monitor is designed for mobile applications for in-vehicle scenarios of all kinds.
Read the safety guidelines thoroughly before starting any servicing on the device. Read the
guidelines before powering up the device, and keep this document for later use.
The operator is solely responsible for any damage resulting from unauthorized modifications to the
device.
Maintenance and Operation Overview
Warning: Do not attempt to disassemble, open, service, or modify the product,
accessories, or power supply to prevent the risk of electric shock or other
hazard. Any evidence that indicates any opening or modifying of the monitor, or
peeling, puncturing, or removing of the labels will void the Limited Warranty.
The Rugged Touch Monitor is designed and manufactured according to strict controls and
following the stated safety regulations. The following list identifies incorrect operating uses of the
Rugged Touch Monitor. Incorrect use of the Rugged Touch Monitor can lead to hardware damage,
safety issues and possible risk to personnel health:
„ The Rugged Touch Monitor is under operation by untrained personnel;
„ The Rugged Touch Monitor is not maintained as recommended;
„ The Rugged Touch Monitor is not used as intended.
█
█
█
█
█
█
█
█
█

3
Safe Environments of Use
Warning: It is recommended you DO NOT remove or install accessories in
fueling areas, facilities for chemical transfer or storage, or areas that contain
grain dust or metal powders, etc. In such environments, sparks can occur and
result in an explosion or fire.
Warning: The use of isolators to avoid system damage while in harsh
environments is recommended. Cables connected to equipment inputs and
outputs are capable of picking up voltage and current noise from disturbances.
As an example, cables near motors can pick up electrical fast transients (EFTs),
while lightning strikes (causing surges) can couple inductively to running
cables, or indirectly through power supplies.
Distractions
Safety
Warning: It is not recommended to use the device while operating machinary or
the use of a vehicle to prevent the occurance of a dangerous situation. Observe
the policies or regulations prohibiting the use of mobile devices.
To prevent injury and damage, read the following safety guidelines prior to operating the
device. The manufacturer assumes no liability for any and all damages arising from misuse or
noncompliance with these guidelines.
Electrical Hazards
Use only Supplied Power Cables
Use only supplied power cables from RuggON.
Environmental Hazards
Do not use the Rugged Touch Monitor in locations near/with flammable gases or vapor.
The use of electrical equipment in explosive environments can be dangerous.
„ Turn off the device when near a gas station, fuel depot, chemical plant or a place where
blasting operations take place.
Security Guidelines for Mounting
„ If installing in a fixed location, it is advised to properly secure the device to prevent theft of
the device.
Environmental
The Rugged Touch Monitor is not intended for use or exposure to extreme temperature
█
█

4
environments for an extended period of time.
Connecting and Disconnecting External Devices
To prevent damage, it is recommended to disconnect the power before removing the cables.
Only Use AuthorizedAccessories
Only use the supplied cables, power packs and other accessories that have been tested and
approved by RuggON. Contact your local distributor for further information.
Cleaning and Servicing
Turn off the device, and disconnect it from external power. Use a soft, dampened cloth (non-
abrasive) with either water or a diluted mild detergent. If a mild detergent is used, ensure all soap
residue is removed. Do not use chemical cleaners.
„ Disconnect the Rugged Touch Monitor from power before cleaning or servicing.
„ Use only a non-abrasive cloth when cleaning.
„ If an alcohol solution is used, see the following:
„ a 75% alcohol solution can be used for cleaning
„ Do not spray the alcohol directly on the monitor or the panel, instead spray the solution
on a cloth and use the cloth to wipe down the chassis
„ The prolonged use of alcohol on the chassis and front panel keys can lead to
discoloration
„ It is recommended to not use an alcohol cleaning solution on the RuggON logo to avoid
discoloration
„ Never clean the Rugged Touch Monitor with compressed air, a pressure washer or a vacuum
cleaner.
„ Clean the surface of the Rugged Touch Monitor with a non-abrasive/non-harsh cloth or
cleaning solution to prevent damage.
„ Do not use cleaning solutions on the panel to prevent damaging it.
„ Only use a nonabrasive cloth to clean the touch-screen.
Touchscreen Care
Rugged Touch Monitor is extremely rugged, designed to withstand extreme conditions, however
the proper care of the touchscreen will aid in prolonging the life of the device. To ensure utmost
performance of the touchscreen, AVOID excessive or prolonged exposure to oil, dust, chemicals,
abrasives, and ultraviolet light.
To help protect the screen:
„ Frequent cleaning is recommended. Use water or an eyeglass cleaner to dampen the cloth.
Wipe the screen with a soft, lint-free, non-abrasive cloth.
Warning: To prevent damage, ensure all cables are secured and the device is
only connected to the recommended power supply.
„ Keep the device in a carry case while in storage or in transit to prevent damage.
„ Ultraviolent light and excessive heat can damage the device. To maintain the condition of the
█
█
█
█
█
█
█
█
█
█
█
█
█
█

5
device, keep it out of the sunlight if not in use. Do not store the RTD S11 in direct sunlight for
unnecessary periods of time.
„ Use a proper touchscreen tools. Use either fingers or a stylus device specifically designed
for use with capacitive touchscreens to operate the touchscreen of this device. The use
of ballpoint pens, metal tools or other sharp objects to operate the touchscreen have the
potential to scratch and/or damage the surface of the touchscreen.
„ Avoid drops, tumbles, and abrasives. Protect the monitor from impact, pressure, and
abrasive substances that can scratch or crack it. The device should not be dropped to
maintain the condition of the device. The use of screen protectors is recommended to keep
the touchscreen clean and protected.
Regional Compliance
U.S.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help
Europe
European Declaration of Conformity
According to ISO / IEC Guide 22 and EN 450 14 Manufacturer’s Name: Ruggon Corporation
Manufacturer’s Address: 4F, No. 298, Yang Guang St., NeiHu. Taipei, Taiwan
Declares, under our sole responsibility, that the product: Product Name: Rugged Touch Monitor,
Model Number: RTDS11, conforms to the following Product Specifications:
„ LVD 2014/35/EU
EN 62368-1: 2014 +A11: 2017
„ EMCD 2014/53/EU
EN 55032/35
EN 50498
█
█
█
█

6
E-Mark
Supplementary Information
In addition, the power supply provided with this product has been certified to IEC 62368-1: 2014
2nd edition and/ or EN 62368-1: 2014 +A11: 2017. As manufacturer, we declare under our sole
responsibility that the equipment follows the provisions of the Standards stated above.
█